Mid-Mount Platform Manual

More documents

Recommendations

Info

OPERA TION 3-5.3 EMERGENCY PUMP UNIT (EPU) If the main hydraulic system is not functioning, the EPU provides back-up power to the main hydraulic system pump. A momentary switch is provided to activate the EPU. NOTE The EPU should only be used when the main system hydraulic pump is not operating. The EPU has a limited run time before overheating. DO NOT run the EPU for more than 30 minutes without allowing an additional 30 minutes for cooling down. Limiting loads and pressures will allow for more efficient use of the EPU, and will also generate less heat. Turntable Console Stabilizer Remote <strong>Manual</strong> Stabilizer Controls (4) (5) NOTE The EPU will be activated only after the desired function is selected. At the turntable control console or the stabilizer remote control, hold the EPU switch in the ON position, then activate the desired function. NOTE If the electronic system has failed, and the manual aerial or stabilizer controls are being used, the EPU switch at the manual stabilizer controls will be the only one active. At the manual stabilizer control station, the EPU will be activated as soon as the switch is held in the ON position. The proper sequence of operation is to activate the desired function, then place the EPU switch in the ON position until the operation is complete, then release the switch before returning the manual control handle to the neutral position.
OPERA TION 3-5.4 EMERGENCY STOP BUTTON. An emergency stop button is provided at three locations: lower control station, turntable control console, and aerial basket controls. Pushing down any of these buttons will stop all aerial functions. Hydraulic oil flow will be blocked from all aerial functions and all electrical controls will be inoperative. To reset, turn and pull up on the emergency stop button. To restore hydraulic functions only, leave the Emergency Stop switch depressed and hold the turntable Emergency Stop Bypass switch. Operate the aerial device using the manual controls. e ~ PieR:e ~ I~. AI RighIs R..- 3-16' ~ ~
Page 1 and 2: ~ 2005 Pierce Manufacturing Inc. Pa
Page 3 and 4: 21.3-21.3-2 EMERGENCY CONTROlS 01.3
Page 5 and 6: THIS PAGE INTENTIONALLY LEFT BLANK
Page 7 and 8: FOREWORD THIS PAGE INTENnONALL Y LE
Page 9 and 10: SAFETY 1-3. LIST OF ABBREVIATIONS 1
Page 11 and 12: SAFETY 91-0790 91-0788 STAND CLEAR
Page 13 and 14: SAFETY Tms PAGE INTENTIONALLY LEFT
Page 15 and 16: GENERAL . Command Zone Information
Page 17 and 18: 200-gailSta~~~ GENERAL Table 2-1. M
Page 19 and 20: GENERAL 2-3.1 COMMAND ZONE INFORMAT
Page 21 and 22: GENERAL 2-3.1.3 Aerial Level Screen
Page 23 and 24: GENERAL 2-3.3 TURNTABLE CONTROL CON
Page 25 and 26: GENERAL 2-3.5 LOWER CONTROL STATION
Page 27 and 28: GENERAL 2-3.6 STABILIZER CONTROLS (
Page 29 and 30: GENERAL 2-3.8 BASKET CONTROLS (LEFT
Page 31 and 32: GENERAL 2-3.10 BASKET CONTROLS (RIG
Page 33 and 34: GENERAL 2-3.12 OIL SAMPLE PORT. 50
Page 35 and 36: GENERAL NOTE The following capabili
Page 37 and 38: OPERATION 3-1.3.2 Positioning Downh
Page 39 and 40: OPERA TION 3-2.2 Water Tower with W
Page 41 and 42: OPERATION TABLE 3-1. SAFE OPERATING
Page 43 and 44: OPERA TION 3-3. AERIAL OPERATION .
Page 45 and 46: OPERA TION (9) (10) (11) A WARNING
Page 47 and 48: OPERA TION (5) (6) Tum off lighting
Page 49: OPERATION 3-5.2 PLATFORM MANUAL CON
Page 53 and 54: OPERATION 3-7. OPTIONAL EQUIPMENT 3
Page 55 and 56: OPERA TION 3-7.1.3 LyfeHoisP Winch
Page 57 and 58: OPERATION THIS PAGE INTENTIONALLY L
Page 59 and 60: MAINTENANCE 4-1.3 Hydraulic Oil Fil
Page 61 and 62: MAINTENANCE ITEMTO CHECKiSERVJCE PR
Page 63 and 64: ~ MAINTENANCE :. ~ TOCHECK/SERVICE
Page 65 and 66: MAINTENANCE The type of service and
Page 67 and 68: MAINTENANCE NOTE SAE standards requ
Page 69 and 70: ~ MAINTENANCE 4-9. LUBRICATION INST
Page 71 and 72: MAINTENANCE Figure 2. 1 ) If necess

Mid-Mount Platform Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?