Series TY-FRB - Tyco Fire Products

Technical Services: Tel: (800) 

http://www.tyco-fireproducts.com 

381-9312 / Fax: (800) 791-5500 

Series TY-FRB — 80 5.6 and and 115 8.0 K-factor K-factor 

Extended Coverage Horizontal Sidewall Sprinklers Sprinklers 

Quick & Standard Response (Light (Light Hazard) Hazard) 

General 

recessed tion, or a adjustment two-piece Style or up 20 to (1/2” 3/4NPT) inchor 

(19,1 Style mm) 30 (3/4” of total NPT) adjustment Recessed Escutcheon from the 

flush with sidewall 6,4 mm (1/4”) position, of recessed or a two-piece adjustment 

Description 

Style or up 20 to (1/2 12,5 mm inch(1/2”) NPT) of ortotal Style adjustment 30 (3/4 

The Series TY-FRB, 5.6,and 8.0 K-factor, 

The Extended Series TY-FRB, Coverage 80 and Horizontal 

115 K-factor, 1/4 ment inch provided (6,4 mm) by the ofRecessed recessed Escutcheon adjust- 

inch from NPT) the flush Recessed sidewall position. Escutcheon The adjust- 

with 

Sidewall Extended Sprinklers Coverage areHorizontal extendedSidewall 

coverage, 

Sprinklers decorative are extended 3 mmcoverage, glass bulb decora- 

total adjustment from the flush sidewall 

ment 

reduces 

or up 

the 

to 

accuracy 

1/2 inch 

to 

(12,7 

which 

mm) 

the fixed 

of 

pipe lengths to the sprinklers must be cut. 

type tive spray 3 mm sprinklers glass bulb designed type spray for sprinklers use position. The adjustment provided by 

in designed hydraulically for use calculated in hydraulically sprinkler calculated the Corrosion Recessed resistant Escutcheon coatings, where reduces applicable, 

are utilized to which to extend the the fixed life of copper pipe 

the 

systems sprinkler insystems light hazard, in light hazard, commercial commercial 

occupancies such such as as churches, res- 

lengths 

accuracy 

occupancies restau- 

alloy sprinklers to the sprinklers beyond that must which be cut. would 

taurant seating seating areas, areas, hotels, hotels, educational educationaties, 

facilities, offices, etc. offices, With their etc. coverage With their up to applicable, corrosive atmospheres. are utilizedAlthough to extend corrosion the 

facili- 

Corrosion otherwise be resistant obtained coatings, when exposed whereto 

coverage 4,9 m (16 up feet) to 16 wide feet by (4,9 7,3 m) m (24 wide ft) by long, life resistant of copper coated alloy sprinklers sprinklers have passed beyond the 

24 

they 

feet 

are 

(7,3 

designed 

m) long, 

for 

they 

installation 

are designed 

along a that standard which corrosion would tests otherwise of applicable be obtained 

approval when agencies, exposed the testing to corrosive is not at- 

rep- 

for installation along a wall or the side 

wall or the side of a beam and just beneath 

of a beam and just beneath a smooth 

smooth and level ceiling. Horizontal 

mospheres. resentative of Although all possible corrosion corrosive resistant 

atmospheres. 

coated Consequently, sprinklers have it is recommended 

passed the 

and level ceiling. Horizontal sidewall 

sidewall sprinklers are commonly used instead 

of pendent or upright sprinklers due that the end 

sprinklers are commonly used instead standard corrosion 

user be consulted 

tests of 

with 

the applicable 

approval agencies, the testing is 

of pendent or upright sprinklers due to 

respect 

aesthetics to aesthetics or or building construction con- 

to the suitability of these coatings for any 

not representative of all possible corrosive 

considerations, where where piping piping across the across ceiling given corrosive 

atmospheres. 

environment. 

Consequently, 

The effects 

it 

theis ceiling not desirable. is not desirable. 

isof recommended ambient temperature, that the end concentration user be 

of chemicals, and gas/chemical velocity, 

The The fast response thermal sensitivity consulted with respect to the suitability 

rating should be considered, as a minimum, along 

rating of the ofSeries the Series TY-FRB, TY-FRB, 3mm Bulb 3 mm Type Bulb of these coatings for any given corrosive 

environment. The effects of ambi- 

Sprinklers 

Sprinklers provides for provides a quick response for a quick 

with the corrosive nature of the chemical to 

Type extended 

coverage 

response 

which the sprinklers will be exposed. 

extended 

(QREC) 

coverage 

rating for many 

(QREC) ent temperature, concentration of 

of the 

Model/Sprinkler 

rating 

coverage 

for many 

areas 

of 

detailed 

the coverage 

in Tables B 

areas chemicals, and gas/chemical velocity, 

and C. 

WARNINGS 

detailed in Tables B and C. 

should be considered, as a minimum, 

along The Series withTY-FRB the corrosive Sprinklers nature described ofherein 

the Identification 

Model/Sprinkler 

The 

The 

recessed version 

version 

of 

of 

the 

the 

Series 

Series 

TY-FRB 

chemical must be installed to which and themaintained sprinklersin will compliance 

with this document, as well as with the 

be 

TY-FRB Extended Extended Coverage Coverage Horizontal HorizontalSprinkler 

Sidewall utilizes Sprinkler either utilizes a two-piece either Style a 10 

Sidewall 

exposed. 

Numbers Identification 

applicable standards of the National Fire 

two-piece (1/2” NPT) Style or Style 10 40 (1/2 (3/4” inch NPT) NPT) Recessed or Protection Association, WARNINGS in addition to the 

TY3332 Numbers 

- EC HSW, 80K, 1/2”NPT 

Style Escutcheon 40 (3/4 with inch12,5 NPT) mm Recessed (1/2”) of recessed Escutcheon 

adjustment withor 1/2 up to inch 19 mm (12,7(3/4”) mm) of of total scribed risdiction. herein Failure must to do be so may installed impair and the TY4332 - EC HSW, 8.0K, 3/4"NPT 

The standards Series of any TY-FRB other authorities Sprinklers having de- 

ju- 

TY4332 

TY3332 

- 

- 

EC HSW, 

EC 

115K, 

HSW, 

3/4”NPT 

5.6K, 1/2"NPT 

adjustment from the flush sidewall posi- 

maintained 

performance 

in 

of these 

compliance 

devices. 

with this 

document, as well as with the applicable 

The standards owner is responsible of the National for maintaining Fire Pro- 

their Approvals Technical 

Technical Data 

IMPORTANT 

Always refer IMPORTANT 

to Technical Data Sheet tection fire protection Association, system and in addition devices in toproper 

the UL and C-UL Listed. 

Always TFP700 refer for the to “INSTALLER TechnicalWARNING” 

Data standards operating condition. of any other The authorities installing contractor 

or jurisdiction. sprinkler manufacturer Failure to should do sobe may con- 

(Refer Approvals to Table A for complete approval 

having 

FM, Data VdS, and NYC Approved. 

Sheet that provides TFP700 cautions for the “INSTALLER 

with respect to 

WARNING” handling and thatinstallation provides cautions 

of sprinkler impair tacted with the any performance questions. of these devices. 

information UL and C-UL including Listed. corrosion resistant 

with systems respect and to handling components. and installation 

handling of sprinkler and installation systems and can com- 

perma- 

The owner is responsible for maintaintion 

(Refer pertaining to Table to A for special complete design approval 

Improper 

status, FM, VdS, as well andas NYC the Approved. 

Design Criteria Secponents. 

considerations.nently 

damage Improper a handling sprinkler system and installation 

or ing their fire protection system and devices 

in proper operating condition. tant status, as well as the Design Cri- 

information including corrosion resis- 

its components 

can permanently 

and cause 

damage 

the sprinkler 

a sprinkler 

to fail 

system 

to operate 

or 

in 

its 

a 

components 

and cause the sprinkler to fail 

fire situation 

or cause it to operate prematurely. manufacturer should be contacted Refer sign considerations.) 

to Table B. 

The installing contractor or sprinkler Maximum teria Section Working pertaining Pressure to special de- 

to operate in a fire situation or cause with any questions. 

it to operate prematurely. 

Maximum Working Pressure 

175 psi (12,1 bar) 

Page 1 of 8 January, 2007 TFP296_EN 

Page 1 of 8 

JANUARY, 2005 

TFP296 

† DuPont Registered Trademark

Page 22of of 8 8 

TFP296_EN 

1 - Frame 

2 - Button 

3 - Sealing 

Assembly 

4 -Assembly 

Bulb 

45 - Bulb Compression 

5 - Compression 

Screw 

6 -Screw 

Deflector 

7 - Ejection 

6 - Deflector 

Spring 

7 - Ejection Spring 

40 1-9/16" mm 

(39,7 (1-9/16”) mm) 

DEFLECTOR 

HAT 

11 7/16" mm 

(11,1 (7/16”) mm) 

117/16" 

mm 

(11,1 (7/16”) mm) 

6 

* 

CENTERLINE 

OF SPRINKLER 

WATERWAY 

* Temperature Temperature rating rating is indicated is indicated on deflector on deflector adjacent or adjacent to orifice toseat orifice on frame. seat on frame. 

**Pipe Pipe 

thread 

thread 

connections 

connections 

per ISO 

per 

7/1 

ISO 

can 

7/1 

be 

can 

provided 

be provided 

on special 

on 

request. 

special request. 

FIGURE 1 

SERIES TY-FRB (TY3332) FIGURE EXTENDED 1 COVERAGE 

SERIES TY-FRB HORIZONTAL (TY3332) EXTENDED SIDEWALL COVERAGE SPRINKLERS HORIZONTAL 

SIDEWALL 5.6 K-FACTOR, SPRINKLERS 1/2 INCH K80, 1/2” NPT NPT 

1 1- Frame - 2 2- Button - 3 3- Sealing - Assembly 

Assembly 

4 - Bulb 

4 5- Bulb - Compression 

5 - Compression Screw 

6 Screw - Deflector 

7 - Ejection 

6 - Deflector 

Spring 

7 - Ejection Spring 

38 1-1/2" mm 

(38,1 (1-1/2”) mm) 

DEFLECTOR 

HAT 

11 7/16" mm 

(11,1 (7/16”) mm) 

CENTERLINE 

OF SPRINKLER 

WATERWAY 

149/16" 

mm 

(14,3 (9/16”) mm) 

6* 

4 

5 

7 

NOMINAL 7/16" 

MAKE-IN (11,1 mm) 

NOMINAL 11 mm 

MAKE-IN (7/16”) 

38 1-1/2" mm 

(38,1 (1-1/2”) mm) 

38 1-1/2" mm 

(38,1 (1-1/2”) mm) 

2 

56 2-3/16" mm 

(55,6 (2-3/16”) mm) 

3 

WRENCH 

FLATS 

1 

5 2 3 1 

57 2-1/4" mm 

(57,2 (2-1/4”) mm) 

WRENCH 

FLATS 

1/2" 

NPT 

3/4" 

NPT 

* Temperature Temperature rating rating is indicated is indicated on deflector on deflector adjacent or adjacent to orifice toseat orifice on frame. seat on frame. 

**Pipe Pipe 

thread 

thread 

connections 

connections 

per ISO 

per 

7/1 

ISO 

can 

7/1 

be 

can 

provided 

be provided 

on special 

on 

request. 

special request. 

FIGURE 2 

SERIES TY-FRB (TY4332) FIGURE EXTENDED 2 COVERAGE 

SERIES TY-FRB HORIZONTAL (TY4332) EXTENDED SIDEWALL COVERAGE SPRINKLERS HORIZONTAL 

SIDEWALL 8.0 K-FACTOR, SPRINKLERS 3/4 K115, INCH3/4” NPT NPT 

4 

7 

NOMINAL 1/2" 

MAKE-IN (12,7 mm) 

12,5 NOMINAL mm 

MAKE-IN (1/2”) 

** 

** 

Discharge Coefficient 

80,6 K = l/min.bar 5.6 GPM/psi 0,5 (5.6 1/2 usgpm/psi (80,6 LPM/bar 0,5 ) 1/2 ) 

115,2 K = 8.0 l/min.bar GPM/psi 0,5 (8.0 1/2 usgpm/psi (115,2 LPM/bar 0,5 ) 1/2 ) 

Temperature Ratings 

Referto to Table A A 

Finishes 

Sprinkler: Refer to Table to Table A. A 

Recessed Escutcheon: White White Coated, Coated, 

ChromePlated, Plated, Brass or Brass Plated Plated 

Physical Characteristics 

Characteristics 

Frame............................................................Bronze 

. . . . . . . . . . . . Button.............................................Brass/Copper 

. . . . . . . . Brass/Copper 

SealingAssembly.................................................. 

. . . . . . . . . . 

................................. . . . . . Beryllium Nickel w/Teflon† w/Teflon* 

Bulb..................................................................Glass 

. . . . . . . . . . . . . . Compression Screw.................................Bronze 

. . . . . 

Deflector....................................................Copper 

Deflector . . . . . . . . . . . Copper 

*Registered trademark of DuPont. 

Operation 

Operation 

The glass Bulb contains a fluid which 

expands when exposed to heat. When 

The the glass ratedbulb temperature contains a fluid is reached, that expands the 

when 

fluid expands 

exposed to 

sufficiently 

heat. When 

to 

the 

shatter 

rated temperature 

is reached, the fluid expands suffi- 

the 

glass Bulb, allowing the sprinkler to 

activate and water to flow. 

ciently to shatter the glass bulb, activating 

the sprinkler and allowing water to flow. 

Design 

Design Criteria Criteria 

The Series TY-FRB Extended CoverageSeries 

Horizontal TY-FRB Extended Sidewall Coverage Sprinklers Hori- 

The 

zontal must Sidewall be installed Sprinklers and utilized must be installed Light 

and Hazard utilized Occupancies, in Light Hazard under Occupancies, smooth 

under level ceilings smooth level as outlined ceilings in as the outlined applicable 

applicable installation installation standard standard recognized rec- 

in 

the 

ognized 

by the Approval 

by the Approval 

Agency 

Agency 

(e.g., UL 

(e.g., 

recognizes 

NFPA 13, and FM recognizes 

UL 

recognizes 

the FM Loss 

NFPA 

Prevention 

13, and FM 

Data 

recognizes 

Sheets). 

the 

FM Only Loss thePrevention Style 10, Data 20, Sheets). 30, or Only 40 Recessed 

10, 20, Escutcheon, 30, or 40 Recessed as applicable, Escutcheon, is 

the 

Style 

as to applicable, be used for is recessed to be used installations. 

for recessed installations. 

Installation 

The Series TY-FRB Sprinklers must be 

installed in accordance with the following 

instructions: 

NOTES 

Do not install any bulb type sprinkler if 

the bulb is cracked or there is a loss of 

liquid from the bulb. With the sprinkler 

held horizontally, a small air bubble 

should be present. The diameter of the 

air bubble is approximately 1/16 inch 

(1,6 mm). 

A leak tight 1/2 inch NPT sprinkler joint 

should be obtained with a torque of 7 

to 14 ft.lbs. (9,5 to 19,0 Nm). A maximum 

of 21 ft. lbs. (28,5 Nm) of torque 

may be used to install sprinklers with 

1/2 NPT connections. A leak tight 3/4 

inch NPT sprinkler joint should be obtained 

with a torque of 10 to 20 ft.lbs. 

DuPont Registered Trademark

TFP296_EN Page 33 of 8 

SPRINKLER FINISH FINISH (See (See Note Note 5) 5) 

K TYPE TEMP. BULB BULB 

NATURAL 

CHROME- WHITE*** 

*** 

K TYPE TEMP. 

LIQUID LIQUID BRASS BRASS 

PLATED 

POLYESTER 

57°C (135°F) Orange 

5.6 EC HSW 135°F/57°C Orange 

EC HSW 

1/2" (TY3332) 68°C (155°F) Red 

1, 2, 1,2,3,4,6 

6 

(TY3332) 155°F/68°C Red 

NPT 

79°C (175°F) Yellow 

175°F/79°C Yellow 

5.680 

RECESSED 


135°F/57°C Orange 

1/2" 1/2” EC EC HSW* HSW* 68°C (155°F) Red 

1, 2, 1,2,4 4 

NPT NPT (TY3332) (TY3332) 155°F/68°C Red 

79°C (175°F) Yellow 


5.6 RECESSED 

RECESSED 


135°F/57°C Orange 

EC HSW** 68°C (155°F) Red 

1,2,3,4 

1/2" EC HSW** 

1, 2, 3, 4 

(TY3332) 155°F/68°C Red 

NPT (TY3332) 79°C (175°F) Yellow 



8.0 EC EC HSW 135°F/57°C Orange 

68°C (155°F) Red 

1,23,4 

3/4" 

(TY4332) 

1, 2, 3, 4 

155°F/68°C 

NPT 

79°C (175°F) 

Red 

Yellow 


115 RECESSED 


1,2,4 

8.0 3/4” RECESSED 

HSW* 135°F/57°C 68°C (155°F) Orange Red 

1, 2, 4 

3/4" NPT EC(TY4332) 

HSW* 

155°F/68°C 

NPT (TY4332) 

79°C (175°F) Red Yellow 1,2,3,4 


1, 2, 3, 4 

RECESSED 


8.0 RECESSED 

HSW** 135°F/57°C 68°C (155°F) Orange Red 

1,2,3,4 

3/4" EC (TY4332) HSW** 

1, 2, 3, 4 

155°F/68°C 79°C (175°F) Red Yellow 

NPT (TY4332) 

NOTES: 


1. Listed by Underwriters Laboratories, Inc. (UL) per Table C. 

NOTES: 2. Listed by Underwriters Laboratories, Inc. for use in Canada per Table C. 

1. 3. Listed Approved by Underwriters by Factory Mutual Laboratories, Research Inc. Corporation (UL) per Table (FM) B. per Table D. 

2. Listed by Underwriters Laboratories, Inc. for use in Canada per Table B. 

4. Approved by the City of New York under MEA 354-01-E. 

3. Approved by Factory Mutual Research Corporation (FM) per Table C. 

4. 5. Approved Where Polyester by the City Coated of New Sprinklers York under are noted MEA to 354-01-E. be UL and C-UL Listed, the sprinklers 

5. are Where UL and Polyester C-UL Listed Coated Corrosion Sprinklers Resistant are noted Sprinklers. to be UL and C-UL Listed, the sprinklers 

6. are VdS UL Approved and C-UL (For Listed details Corrosion contact Resistant Tyco Fire & Sprinklers. Building Products, Enchede, Netherlands, 

6. Tel. VdS +31 Approved 53-428-4444/Fax (For details +31 contact 53-428-3377). Tyco Fire & Building Products, Enchede, Netherlands, 

* Installed Tel. 31-53-428-4444/Fax with Style 10 (1/2” 31-53-428-3377). 

NPT) or Style 40 (3/4” NPT) 3/4” Total Adjustment Recessed 

* 

Escutcheon, 

Installed with 

as applicable. 

Style 10 (1/2" NPT) or Style 40 (3/4" NPT) 3/4" Total Adjustment Recessed 

Escutcheon, as applicable. 

** 

** 

Installed 

Installed 

with 

with 

Style 

Style 

20 

20 

(1/2" 

(1/2” 

NPT) 

NPT) 

or 

or 

Style 

Style 

30 

30 (3/4” 

(3/4" 

NPT) 

NPT) 

1/2” 

1/2" 

Total 

Total 

Adjustment 

Adjustment 

Recessed 

Recessed 

Escutcheon, as applicable. 

TABLE A 

TABLE LABORATORY A, LABORATORY LISTINGS LISTINGS AND AND APPROVALS 

(Refer to to the the Design Criteria Section) 

SPRINKLER FINISH 

(13,4 to 26,8 Nm). A maximum of 30 the deflector is to face towards the 

ft.lbs. (40,7 Nm) of torque is to be used NATURAL ceiling. CHROME WHITE 

K 

TYPE 

to install sprinklers with 3/4 NPT connections. 

Higher EC levels HSWof torque may 

BRASS PLATED POLYESTER 

Step 2. With pipe thread sealant applied17,2 

to the bar pipe (250 threads, psi) hand tighten 

distort 80 the sprinkler (TY3332) inlet and cause 

the sprinkler 

leakage or impairment of the sprinkler. 

orinto the sprinkler fitting. 

1/2” 

Do 

NPT RECESSED EC HSW 

Step 

12,1 

3. Tighten 

bar (175 psi) 

the sprinkler into the 

not attempt to(TY3332) 

make-up for insufficient 

adjustment in the escutcheon 

sprinkler 

(SEE 

fitting 

NOTE 

using 

1) 

only the W-Type 

plate by under- or EC over-tightening HSW 

6 Sprinkler Wrench (Ref. Figure 7). 

the 

115 

sprinkler. Readjust (TY4332) 

With reference to Figures 1 and 2, the 

the position of the 

sprinkler 

3/4” 

W-Type 

fitting to suit. 

12,16bar Sprinkler (175 psi) Wrench is to be 

NPT RECESSED EC HSW 

applied to the sprinkler wrench flats. 

The Series TY-FRB (TY4332) EC Sidewall 

Sprinklers must be installed in accordance 

NOTES: with the following instruc- 

The Series TY-FRB Recessed EC 

Sidewall Sprinklers must be installed 

tions. 1. The maximum working pressure of 17,2 bar (250 psi) only applies to the Listing by 

Underwriters Laboratories, Inc. (UL); the Listing 

in 

by 

accordance 

Underwriters 

with 

Laboratories, 

the following 

Inc. for use 

instructions. 

Step 1. Horizontal sidewall sprinklers 

are 

in 

to 

Canada 

be installed 

(C-UL); and, 

with 

the 

their 

Approval 

centerline 

by the City of New York. 

Step A. Horizontal sidewall sprinklers 

perpendicular to the back wall and parallel 

to the ceiling. The TABLE word B, MAXIMUM “TOP” on WORKING 

are to be installed with their centerline 

PRESSURE 

WRENCH RECESS 

(END"B" “B” USED FOR 

3/4" 3/4” NPT MODELS) 

WRENCH RECESS 

(END"A" “A” USED FOR 

1/2" 1/2” NPT MODELS) 

FIGURE 7 

W-TYPEFIGURE 6 SPRINKLER 3 

W-TYPE 6 SPRINKLER WRENCH WRENCH 

WRENCH 

RECESS 

PUSH 

PUSH 

WRENCH 

WRENCH 

IN TO ENSURE 

IN TO ENSURE 

ENGAGEMENT 

ENGAGEMENT 

WITH SPRINKLER 

WRENCHING WITH SPRINKLER AREA 

WRENCHING AREA 

FIGURE 48 

W-TYPE 7 RECESSED 

SPRINKLER 

SPRINKLER WRENCH 

WRENCH 

perpendicular to the back wall and parallel 

to the ceiling. The word “TOP” on 

the deflector is to face towards the 

ceiling. 

Step B. After installing the Style 10. 

20, 30, or 40 Mounting Plate, as applicable, 

over the sprinkler threads and 

with pipe thread sealant applied to the 

pipe threads, hand tighten the sprinkler 

into the sprinkler fitting. 

Step C. Tighten the sprinkler into the 

sprinkler fitting using only the W-Type 

7 Recessed Sprinkler Wrench (Ref. 

Figure 8). With reference to Figure 1 or 

2, the W-Type 7 Recessed Sprinkler 

Wrench is to be applied to the sprinkler 

wrench flats. 

Step D. After the wall has been installed 

or the finish coat has been applied, 

slide on the Style 10, 20, 30, or 

40 Closure over the Series TY-FRB 

Sprinkler and push the Closure over 

the Mounting Plate until its flange 

comes in contact with the wall.

Page 4 of 8 

TFP296_EN 

Response Rating 

80 K EXTENDED COVERAGE HORIZONTAL SIDEWALL SPRINKLER (TY3332) 

Coverage Area (1) 

m x m (ft x ft) 

Minimum 

Flow (2) 

l/min (gpm) 

Minimum Pressure 

(2) , 

bar (psi) 

Deflector-To- 

Ceiling Distance 

(3) 

mm (in) 

Sprinkler Temperature 

Rating 

°C 

Minimum Spacing 

(4) 

m (ft) 

Quick 4,9 x 4,9 (16 x 16) 98 (26) 1,48 (21.6) 100 - 300 (4 - 12) 57, 68, 79 3,1 (10) 

Quick 4,9 x 5,5 (16 x 18) 110 (29) 1,85 (26.8) 100 - 300 (4 - 12) 57, 68, 79 3,1 (10) 

Quick 4,9 x 6,1 (16 x 20) 121 (32) 2,25 (32.7) 100 - 150 (4 - 6) 57 3,1 (10) 

Quick 4,9 x 6,7 (16 x 22) 133 (35) 2,70 (39.1) 100 - 150 (4 - 6) 57 3,1 (10) 

Standard 4,9 x 6,1 (16 x 20) 121 (32) 2,25 (32.7) 100 - 150 (4 - 6) 68 3,1 (10) 

Standard 4,9 x 6,7 (16 x 22) 133 (35) 2,70 (39.1) 100 - 150 (4 - 6) 68, 79 3,1 (10) 





Minimum 

Flow (2) 

l/min (gpm) 


(2) , 

bar (psi) 

Deflector-To- 


(3) 

mm (in) 


Rating 

°C 


(4) 

m (ft) 

Quick 4,9 x 4,9 (16 x 16) 98 (26) 0,73 (10.6) 100 - 300 (4 - 12) 57, 68, 79 10 (3,1)/13 (4,0) (5) 

Quick 4,9 x 5,5 (16 x 18) 110 (29) 0,90 (13.1) 100 - 300 (4 - 12) 57, 68, 79 10 (3,1)/13 (4,0) (5) 

Quick 4,9 x 6,1 (16 x 20) 121 (32) 1,10 (16.0) 100 - 150 (4 - 6) 57 10 (3,1)/13 (4,0) (5) 

Quick 4,9 x 6,1 (16 x 20) 125 (33) 1,17 (17.0) 100 - 300 (4 - 12) 57 10 (3,1)/13 (4,0) (5) 

Quick 4,9 x 6,7 (16 x 22) 133 (35) 1,32 (19.1) 100 - 150 (4 - 6) 57 10 (3,1)/13 (4,0) (5) 

Quick 4,9 x 6,7 (16 x 22) 136 (36) 1,59 (20.3) 100 - 300 (4 - 12) 57 10 (3,1)/13 (4,0) (5) 

Quick 4,9 x 7,3 (16 x 24) 148 (39) 1,64 (23.8) 100 - 150 (4 - 6) 57 10 (3,1)/13 (4,0) (5) 

Quick 4,9 x 7,3 (16 x 24) 151 (40) 1,72 (25.0) 100 - 300 (4 - 12) 57 10 (3,1)/13 (4,0) (5) 

Standard 4,9 x 6,1 (16 x 20) 121 (32) 1,10 (16.0) 100 - 150 (4 - 6) 68 10 (3,1)/13 (4,0) (5) 

Standard 4,9 x 6,1 (16 x 20) 125 (33) 1,17 (17.0) 100 - 300 (4 - 12) 68 10 (3,1)/13 (4,0) (5) 

Standard 4,9 x 6,7 (16 x 22) 133 (35) 1,32 (19.1) 100 - 150 (4 - 6) 68, 79 10 (3,1)/13 (4,0) (5) 

Standard 4,9 x 6,7 (16 x 22) 136 (36) 1,59 (20.3) 100 - 300 (4 - 12) 68, 79 10 (3,1)/13 (4,0) (5) 

Standard 4,9 x 7,3 (16 x 24) 148 (39) 1,64 (23.8) 100 - 150 (4 - 6) 68, 79 10 (3,1)/13 (4,0) (5) 

Standard 4,9 x 7,3 (16 x 24) 151 (40) 1,72 (25.0) 100 - 300 (4 - 12) 68, 79 10 (3,1)/13 (4,0) (5) 

NOTES 

1. Backwall (where sprinkler is located) by sidewall (length of throw). 

2. Requirement is based on minimum flow in GPM from each sprinkler. The indicted residual pressures are based on the nominal K-factor. 

3. The centerline of the sprinkler waterway is located 11,1 mm (7/16”) below the deflector (Ref. Figures 1 and 2). 

4. Miinimum spacing is for lateral distance between sprinklers located along a single wall. Otherwise adjacent sprinklers (i.e., sidewall 

sprinklers on an adjacent wall, on an opposite wall, or pendent sprinklers) must be located outside of the maximum listed protection 

area of the extended coverage sidewall sprinkler being utilized. 

5. Minimum spacing is 4,0 m (13 feet) when design pressure exceeds 12,1 bar (175 psi), otherwise the minimum spacing is 3,1 m 

(10 feet). 

TABLE C 

UL AND C-UL LISTING COVERAGE AND FLOW RATE CRITERIA






Minimum 

Flow (2) 

l/min (gpm) 


(2) , 

bar (psi) 

Deflector-To- 


(3) 

mm (in) 


Rating 

°C 


(4) 

m (ft) 

Quick 4,9 x 4,9 (16 x 16) 98 (26) 1,51 (22) 100 - 300 (4 - 12) 57, 68 3,1 (10) 

Quick 4,9 x 5,5 (16 x 18) 114 (30) 2,00 (29) 100 - 300 (4 - 12) 57, 68 3,1 (10) 

Quick 4,9 x 6,1 (16 x 20) 125 (33) 2,41 (35) 100 - 300 (4 - 12) 57, 68 3,1 (10) 

Standard 4,9 x 4,9 (16 x 16) 98 (26) 1,51 (22) 100 - 300 (4 - 12) 79 3,1 (10) 

Standard 4,9 x 5,5 (16 x 18) 114 (30) 2,00 (29) 100 - 300 (4 - 12) 79 3,1 (10) 

Standard 4,9 x 6,1 (16 x 20) 125 (33) 2,41 (35) 100 - 300 (4 - 12) 79 3,1 (10) 





Minimum 

Flow (2) 

l/min (gpm) 


(2) , 

bar (psi) 

Deflector-To- 


(3) 

mm (in) 


Rating 

°C 


(4) 

m (ft) 

Quick 4,9 x 4,9 (16 x 16) 121 (32) 1,10 (16.0) 100 - 300 (4 - 12) 57, 68 3,1 (10) 

Quick 4,9 x 5,5 (16 x 18) 136 (36) 1,38 (20) 100 - 300 (4 - 12) 57, 68 3,1 (10) 

Quick 4,9 x 6,1 (16 x 20) 151 (40) 1,72 (25.0) 100 - 300 (4 - 12) 57, 68 3,1 (10) 

Quick 4,9 x 6,7 (16 x 22) 167 (44) 2,06 (30) 100 - 300 (4 - 12) 57, 68 3,1 (10) 

Quick 4,9 x 7,3 (16 x 24) 182 (48) 2,48 (36) 100 - 300 (4 - 12) 57, 68 3,1 (10) 

Standard 4,9 x 4,9 (16 x 16) 121 (32) 1,10 (16.0) 100 - 300 (4 - 12) 79 3,1 (10) 

Standard 4,9 x 5,5 (16 x 18) 136 (36) 1,38 (20) 100 - 300 (4 - 12) 79 3,1 (10) 

Standard 4,9 x 6,1 (16 x 20) 151 (40) 1,72 (25.0) 100 - 300 (4 - 12) 79 3,1 (10) 

Standard 4,9 x 6,7 (16 x 22) 167 (44) 2,06 (30) 100 - 300 (4 - 12) 79 3,1 (10) 

Standard 4,9 x 7,3 (16 x 24) 182 (48) 2,48 (36) 100 - 300 (4 - 12) 79 3,1 (10) 

NOTES 

1. Backwall (where sprinkler is located) by sidewall (length of throw). 

2. Requirement is based on maintaining both minimum flow and minimum residual pressure. 

3. The centerline of the sprinkler waterway is located 11,1 mm (7/16”) below the deflector (Ref. Figures 1 and 2). 

4. Minimum spacing is for lateral distance between sprinklers located along a single wall. Otherwise adjacent sprinklers (i.e., sidewall 

sprinklers on an adjacent wall, on an opposite wall, or pendent sprinklers) must be located outside of the maximum listed protection 

area of the extended coverage sidewall sprinkler being utilized. 

TABLE D 

FM COVERAGE AND FLOW RATE CRITERIA

Page6 6of of 8 8 

TFP296_EN 

5/8±1/4" 16 ± 6 mm 

(15,9±6,4 (5/8 ± 1/4”) mm) 

12,5 1/2±1/8" ± 3 mm 

(12,7±3,2 (1/2 ± 1/8”) mm) 

MOUNTING 

SURFACE 

FACE OF 

SPRINKLER 

FITTING 

MOUNTING 

SURFACE 

FACE OF 

SPRINKLER 

FITTING 

CLOSURE 

CLOSURE 

SERIES 


2-7/8" 73 mm DIA. 

(73,0 (2-7/8”) mm) 

2-1/4" 57 mm DIA. 

(57,2 (2-1/4”) mm) 

SERIES 


2-7/8" 73 mm DIA. 

(73,0 (2-7/8”) mm) 

57 2-1/4" mm DIA. 

(57,2 (2-1/4”) mm) 

MOUNTING 

PLATE 

MOUNTING 

PLATE 

1-1/4" 32 mm (31,8 (1-1/4”) mm) 

3/4" 25 (19,1 mm (1”) mm) 

3,2 1/8" mm 

(3,2 (1/8”) mm) 

19 3/4" mm (19,1 (3/4”) mm) 

61/4" mm (6,4 (1/4”) mm) 

1-1/4" 32 mm (31,8 (1-1/4”) mm) 

1" 25 (25,4 mm mm) (1”) 

3,21/8" 

mm 

(3,2 (1/8”) mm) 

12,5 1/2" mm (12,7 (1/2”) mm) 

1/4" 6 mm (6,4 (1/4”) mm) 

FIGURE 3 

SERIES TY-FRB FIGURE RECESSED 5 EC SIDEWALL 

SERIES SPRINKLER TY-FRB RECESSED ASSEMBLY EC SIDEWALL WITH TWO-PIECE SPRINKLER 

ASSEMBLY 3/4 INCH WITH TOTAL TWO-PIECE ADJUSTMENT 3/4” TOTAL 

ADJUSTMENT STYLE 10STYLE RECESSED 10 RECESSED ESCUTCHEON ESCUTCHEON 

5.6 K-FACTOR, K80, 1/2” 1/2 NPT INCH NPT 

FIGURE 4 

SERIES TY-FRB FIGURE RECESSED 6 EC SIDEWALL 


ASSEMBLY 1/2 INCH WITH TOTAL TWO-PIECE ADJUSTMENT 1/2” TOTAL 

ADJUSTMENT STYLE 20 STYLE RECESSED 20 RECESSED ESCUTCHEON 

5.6 K-FACTOR, K80, 1/2” 1/2 NPT INCH NPT 

5/8±1/4" 16 ± 6 mm 

(15,9±6,4 (5/8 ± mm) 1/4”) 

1/2±1/8" 12,5 ± 3 mm 

(12,7±3,2 (1/2 ± mm) 1/8”) 

MOUNTING 

SURFACE 

FACE OF OF 

SPRINKLER 

FITTING 

MOUNTING 

SURFACE 

FACE FACE OF OF 

SPRINKLER 

FITTING 

CLOSURE 

CLOSURE 

SERIES 


73 2-7/8" mm DIA. 

(73,0 (2-7/8”) mm) 

57 2-1/4" mm DIA. 

(57,2 (2-1/4”) mm) 

SERIES 


73 2-7/8" mm DIA. 

(73,0 (2-7/8”) mm) 

57 2-1/4" mm DIA. 

(57,2 (2-1/4”) mm) 

MOUNTING 

PLATE PLATE 

MOUNTING 

PLATE 

1-1/4" 32 mm (31,8 (1-1/4”) mm) 

3/4" 25 (19,1 mm (1”) mm) 

3,21/8" 

mm 

(3,2 (1/8”) mm) 

3/4" 19 mm (19,1(3/4”) 

mm) 

1/4" 6 mm (6,4(1/4”) 

mm) 

1-1/4" 32 mm (31,8 (1-1/4”) mm) 

1" 25 (25,4 mm (1”) mm) 

3,21/8" 

mm 

(3,2 (1/8”) mm) 

12,5 1/2" mm (12,7(1/2”) 

mm) 

1/4" 6 mm (6,4 (1/4”) mm) 

FIGURE 5 

SERIES TY-FRB RECESSED FIGURE 7 EC SIDEWALL 


ASSEMBLY 3/4 INCHWITH TOTAL TWO-PIECE ADJUSTMENT 3/4” TOTAL 

ADJUSTMENT STYLE 40STYLE RECESSED 40 RECESSED ESCUTCHEON ESCUTCHEON 

8.0 K-FACTOR, K115, 3/4” 3/4NPT 

INCH NPT 

FIGURE 6 

SERIES TY-FRB RECESSED FIGURE 8 EC SIDEWALL 

SERIES SPRINKLER TY-FRB RECESSED ASSEMBLYEC WITH SIDEWALL TWO-PIECE SPRINKLER 

ASSEMBLY 1/2 INCHWITH TOTAL TWO-PIECE ADJUSTMENT 1/2” TOTAL 

ADJUSTMENT STYLE 30 STYLE RECESSED 30 RECESSED ESCUTCHEON ESCUTCHEON 

8.0 K-FACTOR, K115, 3/4” NPT INCH NPT


Installation 

The Series TY-FRB Sprinklers must be installed 

in accordance with the following 

instructions: 

NOTES 

Do not install any bulb type sprinkler if the 

bulb is cracked or there is a loss of liquid from 

the bulb. With the sprinkler held horizontally, 

a small air bubble should be present. The diameter 

of the air bubble is approximately 1,5 

mm (1/16”). 

A leak tight 1/2” NPT sprinkler joint should be 

obtained with a torque of 9,5 to 19 Nm (7 to 

14 ft.lbs.). A maximum of 29 Nm (21 ft.lbs.) 

of torque may be used to install sprinklers 

with 1/2” NPT connections. A leak tight 3/4” 

NPT sprinkler joint should be obtained with 

a torque of 13 to 27 Nm (10 to 20 ft.lbs.). A 

maximum of 40,7 Nm (30 ft.lbs.) of torque is 

to be used to install sprinklers with 3/4” NPT 

connections. Higher levels of torque may distort 

the sprinkler inlet and cause leakage or 

impairment of the sprinkler. 

Do not attempt to make-up for insufficient 

adjustment in the escutcheon plate by underor 

over-tightening the sprinkler. Readjust the 

position of the sprinkler fitting to suit. 

The Series TY-FRB EC Sidewall Sprinklers 

must be installed in accordance with the 

following instructions. 

Step 1. Horizontal sidewall sprinklers are to 

be installed with their centerline perpendicular 

to the back wall and parallel to the 

ceiling. The word “TOP” on the deflector is 

to face towards the ceiling. 

Step 2. With pipe thread sealant applied to 

the pipe threads, hand tighten the sprinkler 

into the sprinkler fitting. 

Step 3. Tighten the sprinkler into the sprinkler 

fitting using only the W-Type 6 Sprinkler 

Wrench (Ref. Figure 7). With reference 

to Figures 1 and 2, the W-Type 6 Sprinkler 

Wrench is to be applied to the sprinkler 

wrench flats. 

The Series TY-FRB Recessed EC Sidewall 

Sprinklers must be installed in accordance 

with the following instructions. 

Step A. Horizontal sidewall sprinklers are 

to be installed with their centerline perpendicular 

to the back wall and parallel to the 

ceiling. The word “TOP” on the deflector is 

to face towards the ceiling. 

Step B. After installing the Style 10. 20, 30, 

or 40 Mounting Plate, as applicable, over 

the sprinkler threads and with pipe thread 

sealant applied to the pipe threads, hand 

tighten the sprinkler into the sprinkler fitting. 

Step C. Tighten the sprinkler into the 

sprinkler fitting using only the W-Type 7 

Recessed Sprinkler Wrench (Ref. Figure 8). 

With reference to Figure 1 or 2, the W-Type 

7 Recessed Sprinkler Wrench is to be applied 

to the sprinkler wrench flats. 

Step D. After the wall has been installed or 

the finish coat has been applied, slide on 

the Style 10, 20, 30, or 40 Closure over the 

Series TY-FRB Sprinkler and push the Closure 

over the Mounting Plate until its flange 

comes in contact with the wall. 

Care and 

Maintenance 

The Series TY-B Sprinklers must be maintained 

and serviced in accordance with the 

following instructions: 

NOTE 

Before closing a fire protection system main 

control valve for maintenance work on the 

fire protection system that it controls, permission 

to shut down the affected fire protection 

systems must be obtained from the proper 

authorities and all personnel who may be affected 

by this action must be notified. 

The owner must assure that the sprinklers are 

not used for hanging of any objects; otherwise, 

non-operation in the event of a fire or 

inadvertent operation may result. 

Absence of an escutcheon, which is used to 

cover a clearance hole, may delay the time to 

sprinkler operation in a fire situation. 

Sprinklers that are found to be leaking or 

exhibiting visible signs of corrosion must 

be replaced. 

Automatic sprinklers must never be painted, 

plated, coated, or otherwise altered after 

leaving the factory. Modified sprinklers 

must be replaced. Sprinklers that have 

been exposed to corrosive products of 

combustion, but have not operated, should 

be replaced if they cannot be completely 

cleaned by wiping the sprinkler with a cloth 

or by brushing it with a soft bristle brush. 

Care must be exercised to avoid damage 

to the sprinklers - before, during, and after 

installation. Sprinklers damaged by dropping, 

striking, wrench twist/slippage, or 

the like, must be replaced. Also, replace any 

sprinkler that has a cracked bulb or that has 

lost liquid from its bulb. (Ref. Installation 

Section). 

Frequent visual inspections are recommended 

to be initially performed for corrosion 

resistant coated sprinklers, after the installation 

has been completed, to verify the 

integrity of the corrosion resistant coating. 

Thereafter, annual inspections per NFPA 25 

should suffice; however, instead of inspecting 

from the floor level, a random sampling 

of close-up visual inspections should be 

made, so as to better determine the exact 

sprinkler condition and the long term integrity 

of the corrosion resistant coating, as 

it may be affected by the corrosive conditions 

present. 

The owner is responsible for the inspection, 

testing, and maintenance of their fire protection 

system and devices in compliance 

with this document, as well as with the 

applicable standards of the National Fire 

Protection Association (e.g. NFPA 25), in addition 

to the standards of any other authorities 

having jurisdiction. The installing contractor 

or sprinkler manufacturer should be 

contacted relative to any questions. 

It is recommended that automatic sprinkler 

systems be inspected, tested, and maintained 

by a qualified Inspection Service in 

accordance with local requirements and/or 

national codes.

Page 8 of 8 

TFP296_EN 

P/N 57 — XXX — X — XXX 

MODEL/SIN 

376 EC HSW K80 TY3332 

396 EC HSW K115 TY4332 

FINISH 

TEMPERATURE 

RATING 

1 NATURAL BRASS 135 57°C (135°F) 

4 WHITE POLYESTER 155 68°C (155°F) 

3 WHITE (RAL9010)* 175 79°C (175°F) 

9 CHROME PLATED 

* For sales outside the Americas only 

TABLE E 

PART NUMBER SELECTION 

SERIES TY-FRB EXTENDED COVERAGE HORIZONTAL SIDEWALL SPRINKLERS 

Limited 

Warranty 

Products manufactured by Tyco Fire & Building 

Products (TFBP) are warranted solely to 

the original Buyer for ten (10) years against 

defects in material and workmanship when 

paid for and properly installed and maintained 

under normal use and service. This 

warranty will expire ten (10) years from 

date of shipment by TFBP. No warranty is 

given for products or components manufactured 

by companies not affiliated by 

ownership with TFBP or for products and 

components which have been subject to 

misuse, improper installation, corrosion, or 

which have not been installed, maintained, 

modified or repaired in accordance with applicable 

Standards of the National Fire Protection 

Association, and/or the standards 

of any other Authorities Having Jurisdiction. 

Materials found by TFBP to be defective 

shall be either repaired or replaced, at 

TFBP’ sole option. TFBP neither assumes, 

nor authorizes any person to assume for it, 

any other obligation in connection with the 

sale of products or parts of products. TFBP 

shall not be responsible for sprinkler system 

design errors or inaccurate or incomplete 

information supplied by Buyer or Buyer’s 

representatives. 

In no event shall TFBP be liable, in contract, 

tort, strict liability or under any other legal 

theory, for incidental, indirect, special 

or consequential damages, including but 

not limited to labor charges, regardless of 

whether TFBP was informed about the possibility 

of such damages, and in no event 

shall TFBP’ liability exceed an amount equal 

to the sales price. 

The foregoing warranty is made in lieu 

of any and all other warranties express 

or implied, including warranties of merchantability 

and fitness for a particular 

purpose. 

This limited warranty sets forth the 

exclusive remedy for claims based on 

failure of or defect in products, materials 

or components, whether the claim is made 

in contract, tort, strict liability or any other 

legal theory. 

This warranty will apply to the full extent 

permitted by law. The invalidity, in whole 

or part, of any portion of this warranty will 

not affect the remainder. 

Ordering 

Procedure 

When placing an order, indicate the full 

product name. Refer to the Price List for 

complete listing of Part Numbers. 

Contact your local distributor for availability. 

Sprinkler Assemblies with NPT Thread 

Connections: 

Specify: (Specify Model/SIN), (specify K-factor), 

(specify temperature rating), Series TY- 

FRB Extended Coverage Horizontal Sidewall 

Sprinkler with (specify type of finish or coating), 

P/N (specify from Table E). 

Recessed Escutcheon: 

Specify: Style (10, 20, 30, or 40) Recessed Escutcheon 

with (specify*) finish, P/N (specify*). 

* Eastern Hemisphere sales only. 

Sprinkler Wrench: 

Specify: W-Type 6 Sprinkler Wrench 

................................................. P/N 56-000-6-387. 

Specify: W-Type 7 Sprinkler Wrench 

................................................. P/N 56-850-4-001. 

Note: This document is a translated document. Translations of any materials into languages other than English are intended 

solely as a convenience to the non-English-reading public. Translation accuracy is neither guaranteed nor implied. If any 

questions arise related to the accuracy of the information contained in the translation, please refer to the English version of 

document TFP296 which is the official version of the document. Any discrepancies or differences created in the translation are 

not binding and have no legal effect for compliance, enforcement or any other purposes. www.quicksilvertranslate.com. 

TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446

Series TY-FRB - Tyco Fire Products

Create successful ePaper yourself

Delete template?

Save as template?