HYPROP manual - UMS

More documents

Recommendations

Info

Get ready to start a measuring campaign Manually Refilling (incl. delivery): Alternatively, take the reservoir syringe, fill it with completely degassed water 1 and take care to avoid bubbles in front of the ceramic. Fill the shaft with water and plug the vacuum syringe filled with ¼ deionized degased water completely over the thread. Pull it, until both snappers are locked. Now, the water from the reservoir syringe is drawn through the ceramic tip into the vacuum syringe. When approximately 10 ml are flushed through the ceramic the <strong>HYPROP</strong> shaft is filled. Figure 4-7 1 Push out all air from the syringe. Now plug the end of the tube with your finger and pull up the syringe. This creates vacuum inside the syringe and dissolved gas is released. Rotate the still evacuated syringe to collect all bubbles from the wall of the syringe. Hold the syringe upright and slide in the piston. Unblock the tube and push out all air. Repeat this procedure until no bubbles are produced anymore. 26/104
Get ready to start a measuring campaign 4.2.3 Degas the sensor head Avoid that the plug connector gets in contact with water. Take care that the piston never recoils abruptly as this might damage the pressure transducer (max. 3 bar)! Please note: new vent cock assembled to the acrylic attachement of the sensor head . Figure 4-4 vent cock vertically: closed to ambient air Figure 4-5 vent cock horizontally: open to ambient air, ventilation of the sensorhead, but closed to vacuum pump. Figure 4-8 Figure 4-9 27/104
Page 1 and 2: User Manual HYPROP
Page 3 and 4: HYPROP system 5.2.5 Stored readings
Page 5 and 6: HYPROP system 1 HYPROP system Labor
Page 7 and 8: HYPROP system Bag 2 (white lock): s
Page 9 and 10: HYPROP system 2. Peters, A., and W.
Page 11 and 12: HYPROP system 1.6 Important note Th
Page 13 and 14: Product description 3 Product descr
Page 15 and 16: Product description 3.2.3 Tensiomet
Page 17 and 18: With tensioLINK ® you are able to
Page 19 and 20: Get ready to start a measuring camp
Page 25: Get ready to start a measuring camp
Page 35 and 36: Set-up the HYPROP 5 Set-up the HYPR
Page 37 and 38: Set-up the HYPROP In the single dev
Page 39 and 40: Set-up the HYPROP Please note the f
Page 41 and 42: Set-up the HYPROP 5.2 Software tens
Page 43 and 44: Set-up the HYPROP Depending on the
Page 45 and 46: Set-up the HYPROP Soil volume Volum
Page 47 and 48: Set-up the HYPROP 5.2.4 Current rea
Page 49 and 50: Set-up the HYPROP Select the scale
Page 51 and 52: Perform a measuring campaign 3. The
Page 53 and 54: Perform a measuring campaign 6.3 Co
Page 55 and 56: Perform a measuring campaign 6.4.4
Page 57 and 58: Perform a measuring campaign Figure
Page 59 and 60: Perform a measuring campaign 6.5 De
Page 61 and 62: Perform a measuring campaign If the
Page 63 and 64: Perform a measuring campaign 3. Ple
Page 65 and 66: Perform a measuring campaign 6.8 Dr
Page 67 and 68: Trouble shooting 8 Trouble shooting
Page 69 and 70: Service and maintenance 9 Service a
Page 71 and 72: Service and maintenance 9.4 Change
Page 73 and 74: Theoretical basics 10 Theoretical b
Page 75 and 76: Theoretical basics 10.3.1 The van G
Page 77 and 78:
Additional notes 11 Additional note
Page 79 and 80:
Additional notes 11.2 Vapour pressu
Page 81 and 82:
Appendix Description of the measuri
Page 83 and 84:
Appendix 12.1.2 Clayey silt (Ut3) S
Page 85 and 86:
Appendix 12.1.3 Slightly loamy Sand
Page 87 and 88:
Appendix Evaluation The additional
Page 89 and 90:
Appendix • After draining the mai
Page 91 and 92:
Appendix 12.3 Parameter list 12.3.1
Page 93 and 94:
Appendix 12.3.3 Parameter listing a
Page 95 and 96:
Appendix 12.5 Technical specificati
Page 97 and 98:
Appendix 12.6 Accessories 12.6.1 HY
Page 99 and 100:
13 List of literature • Brooks, R
Page 101 and 102:
List of literature • Schindler, U
Page 103 and 104:
Index M matric potential ..........
Page 106:
© 2012 UMS GmbH, Munich, Germany P
show all

HYPROP manual - UMS

Create successful ePaper yourself

Delete template?

Save as template?