Very High Speed Counter Module - Esco Drives & Automation

More documents

Recommendations

Info

2-4 Installing the Very High Speed Counter Module Installing the Removable Terminal Block A removable terminal block is supplied with your mounting base assembly. To remove, pull up on the RTB handle. This allows the base to be removed and replaced as necessary without removing any of the wiring. To reinsert the removable terminal block, proceed as follows. 1. Insert the RTB end opposite the handle into the base unit. This end has a curved section that engages with the mounting base. Hook the RTB end into the mounting base end, and rotate until it locks into place. 2. Rotate the terminal block into the mounting base until it locks itself in place. 3. If an I/O module is installed, snap the RTB handle into place on the module. Removing a Mounting Base To remove a mounting base, you must remove any installed module, and remove the removable terminal block (if wired). 1. Unlatch the RTB handle on the I/O module. 2. Pull on the RTB handle to remove the removable terminal block. 3. Press in on the module lock on the top of the module and pull up on the I/O module to remove from the base. 4. Remove the module to the right of the base you are removing. (The interlocking portion of the base sits under the adjacent module.) 5. Use a small bladed screwdriver to rotate the orange DIN rail locking screw on the mounting base to a vertical position. This releases the locking mechanism. 6. Then lift the mounting base straight up to remove. Publication 1734-UM003A-EN-P - August 2000
Installing the Very High Speed Counter Module 2-5 Wiring the 24V dc Very High Speed Counter Module Module Status Network Status Status of Input A Status of Input B Status of Input Z Status of Output 0 Status of Output 1 0 1 0 1 Input A Input B Input Aret Input Bret Chassis Ground Chassis Ground RET 0 RET 1 Input Z Input Zret -Vaux -Vaux Out 0 Out 1 +Vaux +Vaux 42016 Module 1 Module 2 0 1 A 2 3 Bret B 4 5 Zret Z 6 7 Out 0 Aret Out 1 0 1 Chas Gnd 2 3 RET 0 Chas Gnd RET 1 4 5 -Vaux -Vaux 6 7 +Vaux +Vaux Module 1 Terminations Module 2 Terminations 0 A 0 Chassis ground 1 Aret 1 Chassis ground 2 B 2 Out 1 RET 3 Bret 3 Out 0 RET 4 Z 4 Vaux - 5 Zret 5 Vaux - 6 Out 0 6 Vaux + 7 Out 1 7 Vaux + Publication 1734-UM003A-EN-P - August 2000
Page 1 and 2: Very High Speed Counter Module Cat.
Page 3 and 4: Preface Purpose of This Manual This
Page 5 and 6: Preface 3 Definitions The following
Page 7 and 8: Table of Contents Important User In
Page 9 and 10: Chapter 1 About the Very High Speed
Page 11 and 12: About the Very High Speed Counter M
Page 23 and 24: Chapter 2 Installing the Very High
Page 25: 0 1 2 3 Installing the Very High Sp
Page 29 and 30: Chapter 3 Very High Speed Counter M
Page 31 and 32: Very High Speed Counter Module Inpu
Page 41 and 42: Chapter 4 Configuring Your Very Hig
Page 43 and 44: Configuring Your Very High Speed Co
Page 49 and 50: Chapter 5 Accessing Instantiated In
Page 51 and 52: Accessing Instantiated Instances 5-
Page 53 and 54: Chapter 6 Troubleshooting with the
Page 55 and 56: Appendix A Specifications Specifica
Page 57 and 58: Specifications A-3 Input Derating C
Page 59 and 60: Index A active features per mode 1-
Page 61 and 62: Allen-Bradley Publication Problem R
Page 64: Back Cover Publication 1734-UM003A-

Very High Speed Counter Module - Esco Drives & Automation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?