Springs and Spring Washers - Electronic Fasteners Inc

More documents

Recommendations

Info

METRIC DISC SPRING WASHERS Stock sizes in high carbon or chrome vanadium Manufactured for general purpose use. These items are manufactured under strict quality control to meet the physical dimensions listed in the following tables (pages 105-108). Our SPEC disc spring washers are ideal for general purpose applications where a tight load tolerance is not required. These parts have been set out to minimize height loss after compression. Stacked disc springs Additional load or deflection can be obtained by stacking disc springs in series or in parallel. See charts below. Tolerances Diameter: I.D. and O.D. shown on pages 105-108 are minimum and maximum dimensions, respectively. For manufacturing tolerances, please contact our Engineering Department at 1-800-872-7732. Load: Values shown on pages 105-108 are for reference only. Loads shown are theoretical and approximate. For applications that require tight load tolerances, please contact our Engineering Department at the above number for feasibility. Material Thickness less than 1.25mm: Carbon Steel per C1074-1075. Thickness 1.25 mm and up: Carbon Steel per C1074-1075 or Chrome Vanadium per SAE 6150. H H 1 P 1 F I.D. O.D. t O.D.= Outside Diameter I.D.= Inside Diameter t= Thickness H= Approx. Free height H 1 = Loaded Height P 1 = Load at deflection F (Reference only) F= Deflection H-H 1 Shown below are the comparative force/deflection graphs for the alternative methods of stacking. METRIC DISC SPRINGS 106 TO ORDER: WWW.ASRAYMOND.COM OR SEE PHONE & FAX NUMBERS ON BACK COVER
METRIC DISC SPRING WASHERS Catalog Number Min I.D. Max O.D. Thickness (t) Free Height (H) Loaded Height (H 1 ) Load at H 1 (P 1 ) (Reference Only) in mm in mm in mm in mm in mm lb N BD006-030 0.126 3.2 0.236 6 0.0118 0.30 0.0177 0.45 0.0134 0.34 26.8 119 BD008-020-0032 0.126 3.2 0.315 8 0.0079 0.20 0.0157 0.40 0.0098 0.25 5.8 26 BD008-030-0032 0.126 3.2 0.315 8 0.0118 0.30 0.0216 0.55 0.0142 0.36 23.4 104 BD008-040-0032 0.126 3.2 0.315 8 0.0157 0.40 0.0236 0.60 0.0177 0.45 41.6 185 BD008-050-0032 0.126 3.2 0.315 8 0.0197 0.50 0.0276 0.70 0.0217 0.55 80.3 357 BD008-020 0.165 4.2 0.315 8 0.0080 0.20 0.0180 0.45 0.0102 0.26 8.8 39 BD008-030 0.165 4.2 0.315 8 0.0120 0.30 0.0220 0.55 0.0142 0.36 26.8 119 BD008-040 0.165 4.2 0.315 8 0.0160 0.40 0.0240 0.60 0.0177 0.45 47.2 210 BD010-030 0.126 3.2 0.394 10 0.0118 0.30 0.0256 0.65 0.0154 0.39 22.0 98 BD010-040-0032 0.126 3.2 0.394 10 0.0157 0.40 0.0276 0.70 0.0189 0.48 40.2 179 BD010-050-0032 0.126 3.2 0.394 10 0.0197 0.50 0.0295 0.75 0.0220 0.56 62.5 278 BD010-040-0042 0.165 4.2 0.394 10 0.0157 0.40 0.0276 0.70 0.0189 0.48 42.5 189 BD010-050-0042 0.165 4.2 0.394 10 0.0197 0.50 0.0295 0.75 0.0220 0.56 66.1 294 BD010-060-0042 0.165 4.2 0.394 10 0.0236 0.60 0.0335 0.85 0.0260 0.66 112.8 502 BD010-025 0.205 5.2 0.394 10 0.0100 0.25 0.0220 0.55 0.0130 0.33 13 58 BD010-040 0.205 5.2 0.394 10 0.0160 0.40 0.0280 0.70 0.0189 0.48 47.9 213 BD010-050 0.205 5.2 0.394 10 0.0200 0.50 0.0300 0.75 0.0220 0.56 74 329 BD012-040-0042 0.165 4.2 0.472 12 0.0157 0.40 0.0315 0.80 0.0197 0.50 40.0 178 BD012-050-0042 0.165 4.2 0.472 12 0.0197 0.50 0.0335 0.85 0.0232 0.59 63.8 284 BD012-060-0042 0.165 4.2 0.472 12 0.0236 0.60 0.0394 1.00 0.0276 0.70 125.0 556 BD012-050-0052 0.205 5.2 0.472 12 0.0197 0.50 0.0354 0.90 0.0236 0.60 78.5 349 BD012-060-0052 0.205 5.2 0.472 12 0.0236 0.60 0.0374 0.95 0.0272 0.69 113.7 506 BD012-050 0.244 6.2 0.472 12 0.0197 0.50 0.0335 0.85 0.0232 0.59 73.3 326 BD012-060 0.244 6.2 0.472 12 0.0236 0.60 0.0374 0.95 0.0272 0.69 123.9 551 BD013-050-0052 0.205 5.2 0.492 12.5 0.0197 0.50 0.0335 0.85 0.0232 0.59 61.1 272 BD013-035 0.244 6.2 0.492 12.5 0.0140 0.35 0.0310 0.80 0.0181 0.46 34.2 152 BD013-050 0.244 6.2 0.492 12.5 0.0200 0.50 0.0330 0.85 0.0232 0.59 65.4 291 BD013-070 0.244 6.2 0.492 12.5 0.0280 0.70 0.0390 1.00 0.0307 0.78 151.3 673 BD014-035 0.283 7.2 0.551 14 0.0140 0.35 0.0310 0.80 0.0181 0.46 27.7 123 BD014-050 0.283 7.2 0.551 14 0.0200 0.50 0.0350 0.90 0.0236 0.6 62.7 279 BD014-080 0.283 7.2 0.551 14 0.0310 0.80 0.0430 1.10 0.0343 0.87 182.8 813 BD015-040-0052 0.205 5.2 0.591 15 0.0157 0.40 0.0374 0.95 0.0213 0.54 39.3 175 BD015-050-0052 0.205 5.2 0.591 15 0.0197 0.50 0.0394 1.00 0.0248 0.63 62.5 278 BD015-060-0052 0.205 5.2 0.591 15 0.0236 0.60 0.0413 1.05 0.0280 0.71 91.5 407 BD015-070-0052 0.205 5.2 0.591 15 0.0276 0.70 0.0433 1.10 0.0315 0.80 124.8 555 BD015-050-0062 0.244 6.2 0.591 15 0.0197 0.50 0.0394 1.00 0.0248 0.63 65.0 289 BD015-060-0062 0.244 6.2 0.591 15 0.0236 0.60 0.0413 1.05 0.0280 0.71 95.1 423 BD015-070-0062 0.244 6.2 0.591 15 0.0276 0.70 0.0433 1.10 0.0315 0.80 129.7 577 BD015-050 0.323 8.2 0.591 15 0.0197 0.50 0.0394 1.00 0.0248 0.63 74.9 333 BD015-070 0.323 8.2 0.591 15 0.0276 0.70 0.0433 1.10 0.0315 0.80 149.5 665 BD015-080 0.323 8.2 0.591 15 0.0315 0.80 0.0472 1.20 0.0354 0.90 220.8 982 BD016-040 0.323 8.2 0.63 16 0.0160 0.40 0.0350 0.90 0.0209 0.53 34.8 155 BD016-060 0.323 8.2 0.63 16 0.0240 0.60 0.0410 1.05 0.0280 0.71 92.6 412 BD016-070 0.323 8.2 0.63 16 0.0276 0.70 0.0453 1.15 0.0319 0.81 143.2 637 BD016-080 0.323 8.2 0.63 16 0.0315 0.80 0.0472 1.20 0.0354 0.90 185.5 825 BD016-090 0.323 8.2 0.63 16 0.0350 0.90 0.0490 1.25 0.0390 0.99 225 1000 BD018-040-0062 0.244 6.2 0.709 18 0.0157 0.40 0.0394 1.00 0.0217 0.55 31.2 139 BD018-050-0062 0.244 6.2 0.709 18 0.0197 0.50 0.0433 1.10 0.0256 0.65 55.1 245 BD018-060-0062 0.244 6.2 0.709 18 0.0236 0.60 0.0472 1.20 0.0295 0.75 89.9 400 BD018-070-0062 0.244 6.2 0.709 18 0.0276 0.70 0.0492 1.25 0.0331 0.84 124.1 552 BD018-080-0062 0.244 6.2 0.709 18 0.0315 0.80 0.0512 1.30 0.0362 0.92 163.0 725 BD018-050-0082 0.323 8.2 0.709 18 0.0197 0.50 0.0433 1.10 0.0256 0.65 59.6 265 BD018-070-0082 0.323 8.2 0.709 18 0.0276 0.70 0.0492 1.25 0.0331 0.84 134.0 596 BD018-080-0082 0.323 8.2 0.709 18 0.0315 0.80 0.0512 1.30 0.0362 0.92 130.8 582 BD018-100-0082 0.323 8.2 0.709 18 0.0394 1.00 0.0551 1.40 0.0433 1.10 265.5 1181 BD018-045 0.362 9.2 0.709 18 0.0180 0.45 0.0410 1.05 0.0236 0.6 48.1 214 BD018-070 0.362 9.2 0.709 18 0.0280 0.70 0.0470 1.20 0.0327 0.83 128.6 572 BD018-100 0.362 9.2 0.709 18 0.0390 1.00 0.0550 1.40 0.0433 1.1 281 1250 BD020-060-0082 0.323 8.2 0.787 20 0.0236 0.60 0.0512 1.30 0.0303 0.77 92.6 412 BD020-070-0082 0.323 8.2 0.787 20 0.0276 0.70 0.0531 1.35 0.0339 0.86 127.7 568 BD020-080-0082 0.323 8.2 0.787 20 0.0315 0.80 0.0551 1.40 0.0374 0.95 168.8 751 BD020-090-0082 0.323 8.2 0.787 20 0.0354 0.90 0.0571 1.45 0.0409 1.04 214.2 953 BD020-100-0082 0.323 8.2 0.787 20 0.0394 1.00 0.0610 1.55 0.0449 1.14 290.9 1294 BD020-050 0.402 10.2 0.787 20 0.0200 0.50 0.0450 1.15 0.0260 0.66 57.1 254 TO ORDER: WWW.ASRAYMOND.COM OR SEE PHONE & FAX NUMBERS ON BACK COVER 107 METRIC DISC SPRINGS
Page 2 and 3:
In addition to the SPEC products de
Page 4 and 5:
120-121 56-63 64-87 112-117 4-45 46
Page 6 and 7:
COMPRESSION SPRINGS COMPRESSION SPR
Page 8 and 9:
COMPRESSION SPRINGS 6 MUSIC WIRE ST
Page 10 and 11:
COMPRESSION SPRINGS 8 MUSIC WIRE ST
Page 12 and 13:
COMPRESSION SPRINGS 10 MUSIC WIRE S
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
MUSIC WIRE Outside Diameter (OD) Ca
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
COMPRESSION SPRINGS MUSIC WIRE STAI
Page 48 and 49:
HIGH PERFORMANCE COMPRESSION SPRING
Page 50 and 51:
TO ORDER: WWW.ASRAYMOND.COM OR SEE
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59: HEAVY DUTY COMPRESSION SPRINGS HEAV
Page 60 and 61: HEAVY DUTY COMPRESSION SPRINGS 58 S
Page 62 and 63: HEAVY DUTY COMPRESSION SPRINGS 60 S
Page 64 and 65: HEAVY DUTY COMPRESSION SPRINGS STOC
Page 66 and 67: EXTENSION SPRINGS EXTENSION SPRINGS
Page 68 and 69: Outside Diameter (OD) Catalog Numbe
Page 90 and 91: TORSION SPRINGS TORSION SPRINGS Sto
Page 92 and 93: TORSION SPRINGS - STAINLESS STEEL M
Page 94 and 95: TORSION SPRINGS - MUSIC WIRE M Sugg
Page 96 and 97: CONICAL COMPRESSION SPRINGS Stock s
Page 98 and 99: CONTINUOUS LENGTH SPRINGS Round Wir
Page 100 and 101: BELLEVILLE SPRING WASHERS Stock siz
Page 102 and 103: BELLEVILLE SPRING WASHERS 100 BELLE
Page 104 and 105: CLOVER ® DOME SPRING WASHERS Stock
Page 106 and 107: CLOVER ® DOME SPRING WASHERS Catal
Page 110 and 111: METRIC DISC SPRINGS 108 METRIC DISC
Page 112 and 113: METRIC DISC SPRINGS METRIC DISC SPR
Page 114 and 115: CURVED SPRING WASHERS Precision eng
Page 116 and 117: WAVE SPRING WASHERS Stock sizes in
Page 118 and 119: WAVE SPRING WASHERS COMPRESSION TYP
Page 120 and 121: MULTIWAVE COMPRESSION SPRINGS Stock
Page 122 and 123: FINGER SPRING WASHERS Stock sizes i
Page 124 and 125: URETHANE SPRINGS URETHANE COMPRESSI
Page 126 and 127: STOCK URETHANE COMPRESSION SPRINGS
Page 128 and 129: 600 STOCK URETHANE COMPRESSION SPRI
Page 130 and 131: STOCK URETHANE COMPRESSION SPRINGS
Page 132 and 133: URETHANE SPRINGS STOCK URETHANE FUL
Page 134 and 135: GAS SPRINGS NITROGEN GAS SPRINGS St
Page 136 and 137: GAS SPRINGS 134 N SERIES Catalog Nu
Page 142 and 143: GAS SPRINGS 140 S SERIES Catalog Nu
Page 148 and 149: S SERIES Catalog Number S14UBM0500
Page 150 and 151: GAS SPRING END FITTINGS PART NUMBER
Page 152 and 153: GAS SPRING MOUNTING HARDWARE PART N
Page 158 and 159:
GAS SPRING MOUNTING HARDWARE PART N
Page 160 and 161:
INTERLOCK GARTER SPRINGS Stock size
Page 162 and 163:
GARTER SPRINGS INTERLOCK GARTER SPR
Page 164 and 165:
RETAINING RINGS W O.D. HOUSING SIZE
Page 166 and 167:
W I.D. A SHAFT SIZE t Light duty si
Page 168 and 169:
Internal Retaining Rings (Circlip s
Page 170 and 171:
FASTENERS - HEX HEAD CAP SCREWS AND
Page 172 and 173:
FASTENERS UNC (USS) Part No. TPI-8
Page 174 and 175:
SPRING PINS, PINS AND RINGS Coiled
Page 176 and 177:
Metric Rolled Spring Pins • Meets
Page 178 and 179:
TOOL CLIPS A A. Tool Clip - Type No
Page 180 and 181:
SPRING - LOADED DEVICES PLUNGERS De
Page 182 and 183:
STOCK PACKAGED ASSORTMENTS AND KITS
Page 184 and 185:
PACKAGED ASSORTMENTS STOCK WAVE SPR
Page 186 and 187:
PACKAGED ASSORTMENTS STOCK EXTENSIO
Page 188 and 189:
PACKAGED ASSORTMENTS COMPRESSIONS S
Page 190 and 191:
PACKAGED ASSORTMENTS EXTENSION SPRI
Page 192 and 193:
MECHANICAL COMPRESSION SPRING STRUT
Page 194 and 195:
HANDLES STEEL CORE MOLDED GRAB HAND
Page 196 and 197:
HANDLES ASSIST HANDLE • 5/8” di
Page 198 and 199:
HANDLES ACTIVATING HANDLE • Zinc
Page 200 and 201:
HANDLES TWO POINT KEY-LOCKING STEEL
Page 202 and 203:
LATCHES & CATCHES ROTARY PADDLE LAT
Page 204 and 205:
LATCHES & CATCHES - RODS & ROD GUID
Page 206 and 207:
LATCHES & CATCHES STANDARD CAMS •
Page 208 and 209:
LATCHES & CATCHES TOUCH LATCH • N
Page 210 and 211:
LATCHES & CATCHES SPRING BOLT LATCH
Page 212 and 213:
LATCHES & CATCHES STRIKE • Chrome
Page 214 and 215:
CHECKS, HOLDERS & PROPS STANDARD DO
Page 216 and 217:
CHECKS, HOLDERS & PROPS TELESCOPIC
Page 218 and 219:
DRAWER SLIDES DS-300 SERIES • Zin
Page 220 and 221:
DRAWER SLIDES DS-SSR1 SERIES • 30
Page 222 and 223:
ALMEN STRIPS FROM ASSOCIATED SPRING
Page 224 and 225:
Associated Spring Raymond - SPEC ha
Page 226 and 227:
TERMS OF SALE 1. With respect to go
Page 228:
Associated Spring-Raymond United St
show all

Springs and Spring Washers - Electronic Fasteners Inc

Create successful ePaper yourself

Delete template?

Save as template?