Download My SINUMERIK Operate - CNC4you - Siemens

More documents

Recommendations

Info

3.1 Setting up The following sections contain information for setting the zero offset and measuring workpieces and tools in JOG. 3.1.1 Setting the zero point In the “Set ZO” dialog box, you can write direct position values for individual axes in the actual value display. The difference between the position value in the machine coordinate system (MCS) and the workpiece coordinate system (WCS) is saved in the active zero offset. Requirement: A zero offset must be active. 36
3.1.2 Workpiece zero You are guided graphically for setting the workpiece zero. To determine the zero point, determine the length of the workpiece and save the position of the cylinder face surface in the direction Z in a zero offset. When the workpiece zero/zero offset is calculated, the tool length is automatically taken into account. If you wish to measure the workpiece zero in “Measuring Only” mode, the measured values are merely displayed without any changes being made to the coordinate system. 3.1.3 Tool measurement You are guided graphically for calibrating the tools (all tool types). Turning technology 37
Page 1: User Guide My SINUMERIK Operate
Page 4 and 5: 3.5 Contour turning................
Page 7: 1 Introduction The SINUMERIK Operat
Page 10 and 11: 2.1 Uniform user interface for turn
Page 12 and 13: Tool management Efficient managemen
Page 14 and 15: 2.2 Help screens, animated elements
Page 16 and 17: 2.3 TSM mode/zero offsets or In TSM
Page 18 and 19: You can configure the editor for Sh
Page 20 and 21: You can use parameters and variable
Page 22 and 23: or The tool wear list contains all
Page 24 and 25: 2.6 Zero offset This view shows in
Page 26 and 27: You can also store and display subd
Page 28 and 29: 28 In this view, you assign the ass
Page 30 and 31: or • 3D cross-section view detail
Page 32 and 33: or If required, you can activate th
Page 35: 3 Turning technology In addition to
Page 39 and 40: Define the main and counterclamp ho
Page 41 and 42: The technology data is directly int
Page 43 and 44: As example, you see from the above
Page 45 and 46: Cycle for centering at any position
Page 47 and 48: Cycle for the input of free positio
Page 49 and 50: 3.3.3 Drilling with programGUIDE To
Page 51 and 52: 3.4 Turning This section provides a
Page 53 and 54: Thread cycle for longitudinal threa
Page 55 and 56: or Plunge-turning cycle for machini
Page 57 and 58: 3.5.3 Contour turning with programG
Page 59 and 60: Enter the name of a program (PRG) t
Page 61 and 62: Cycle to produce a rectangular spig
Page 63 and 64: 3.7 Contour milling This section pr
Page 65 and 66: 3.7.2 Contour milling with ShopTurn
Page 67 and 68: 3.7.3 Contour milling with programG
Page 69 and 70: Create the unmachined and finished
Page 71 and 72: 3.9 Measuring in the Automatic mode
Page 73: Turn a 70-mm diameter with the stoc
Page 76 and 77: 4.1 Setting up In addition to the g
Page 78 and 79: You can select favorites for the me
Page 80 and 81: 4.1.5 Swiveling in JOG The swivel f
Page 82 and 83: The technology data such as the too
Page 84 and 85: 84 The example shown here uses the
Page 86 and 87:
Cycle for drill holes with drilling
Page 88 and 89:
4.4 Milling cycles An overview of t
Page 90 and 91:
Cycle for producing a rectangular s
Page 92 and 93:
4.5 Contour milling This section pr
Page 94 and 95:
4.5.2 Contour milling with ShopMill
Page 96 and 97:
4.5.3 Contour milling with programG
Page 98 and 99:
Enter the name for a program to be
Page 100 and 101:
The CYCLE800 swivel cycle is used t
Page 102 and 103:
You can specify a scale factor for
Page 104 and 105:
Measuring cycles for workpiece prob
Page 106 and 107:
106
Page 108 and 109:
5.1 Tool management or For multitas
Page 110 and 111:
5.2.3 Turning with programGUIDE and
Page 112 and 113:
5.2.5 Milling with programGUIDE and
Page 114 and 115:
5.3 Milling-turning technology with
Page 116 and 117:
Grooving cycle without rounding Ext
Page 118 and 119:
5.3.3 Contour turning in the millin
Page 120 and 121:
5.3.3.2 Contour turning with progra
Page 122 and 123:
First insert the contour call at th
Page 124 and 125:
5.4 Multi-channel machining You can
Page 126 and 127:
5.4.3 Multi-channel program data Op
Page 128 and 129:
5.4.6 Synchronous view You can use
Page 130 and 131:
5.4.9 Program control In Automatic
Page 132 and 133:
132
Page 134 and 135:
6.2 Shortcuts Functions - Softkeys
Page 136 and 137:
Simulation and simultaneous recordi
Page 138 and 139:
138
Page 140 and 141:
Contour............................
Page 142:
CNC equipment of SINUMERIK www.siem
show all

Download My SINUMERIK Operate - CNC4you - Siemens

Create successful ePaper yourself

Delete template?

Save as template?