Instruction Manual - GME
Instruction Manual - GME
Instruction Manual - GME
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
SETTING THE PAGing IDENT<br />
For the Paging feature to work, you must program your<br />
TX4400 with the Selcall Ident of the radio you wish to<br />
transfer the incoming calls to. This PAGE Ident is stored<br />
in memory location 11 of the 'Call To' memory. It is<br />
programmed in the same way as other Selcall Idents.<br />
1. Press the CALL button to select the ‘CALL TO’ mode.<br />
‘CALL TO’ will be displayed with a memory location<br />
number on the left and an associated 5 digit Selcall<br />
Ident or ALPHA Name on the right.<br />
2. Rotate the Channel switch to select the memory<br />
location 11. If your radio is in ALPHA mode, PAGER will<br />
be displayed. This is a fixed ALPHA name for the Paging<br />
memory and cannot be changed. If necessary, briefly<br />
press the F key followed by the ALPHA key to select the<br />
IDENT display mode.<br />
Select<br />
Memory Location 11<br />
3. Enter the required Selcall ident as<br />
follows:<br />
(a) Briefly press the Channel knob. The right-hand<br />
digit of the Selcall Ident will flash.<br />
(b) Rotate the Channel knob to select the required<br />
number in the flashing digit position.(c) Briefly<br />
press the Channel knob again to select the next<br />
digit position.<br />
(d) Repeat steps (b) and (c) to program all 5 digits as<br />
required.<br />
4. Now press and hold the Channel knob. The Selcall Ident<br />
will flash for a few seconds, then the radio will beep as<br />
the Ident is stored in the Paging memory.<br />
MONITORING A SINGLE CHANNEL WHILE IN<br />
PAGE MODE<br />
To monitor a single channel in the Page mode:<br />
1. Select the required channel using the channel switch.<br />
2. Briefly press the F key followed by the PAGE key. 'PAGE'<br />
will be displayed along with the selected channel. The<br />
page mode is now active.<br />
Selected<br />
Channel<br />
Call To<br />
Mode<br />
Enter<br />
Pager Ident<br />
Page<br />
Mode<br />
Selected<br />
Note: The display lighting will extinguish after 10 seconds<br />
to conserve power in case the radio is to be left in Page<br />
mode for an extended period. This also makes the radio less<br />
visible if it is left in an unattended vehicle at night.<br />
Once the Page mode is selected, you can transmit and receive<br />
on the selected channel in the usual way. However, the<br />
Channel switch and the SCAN, OS/GS, DUP and CALL<br />
keys are disabled.<br />
Note: If the selected channel has been tagged for Quiet<br />
operation, the QUIET mode will be automatically selected and<br />
QUIET will be displayed. In this case, you will not be able to<br />
transmit.<br />
If you Selcall Ident is received on the selected<br />
channel:<br />
Your TX4400 will send an acknowledge beep back to the<br />
Caller then change to the Paging channel and transmit the<br />
Page Ident. It will finally return to the selected channel,<br />
sound the alarm and display the Ident or Alpha Name of<br />
the Caller.<br />
Meanwhile the other receiver will be beeping to tell you<br />
that someone has called you. You can then return to your<br />
TX4400, identify the Caller’s Ident and return the call.<br />
Note: Before transmitting on the Paging channel, the<br />
TX4400 will check the channel for activity and will not<br />
transmit if the channel is in use. Only when the channel is<br />
clear will the paging Ident be sent.<br />
SCANning IN PAGE MODE<br />
1. Select the required SCAN group, program the required<br />
channels and then briefly press the SCAN key. The radio<br />
will begin scanning.<br />
2. Now briefly press the F key followed by the PAGE key.<br />
'PAGE' will be displayed.<br />
Using Open Scan<br />
If the radio is scanning in the Open Scan mode, you will not<br />
be able to transmit unless the scan has stopped on a<br />
busy channel.<br />
Using Group Scan<br />
If the radio is scanning in the Group scan mode, you can transmit<br />
on the Priority channel at any time.<br />
Using the QUIET mode<br />
If any channels have been tagged for Quiet operation, the<br />
QUIET mode will be automatically selected and 'QUIET' will<br />
be displayed. You will not be able to transmit.<br />
If while scanning on any channel, your Selcall Ident is<br />
received:<br />
PAGE 16 INSTRUCTION MANUAL TX4400