Download PDF - Black Box (UK)

More documents

Recommendations

Info

Media Converters Standalone 10Mbps 10 Mbps Standalone Media Converters | Distance Chart Speed Model Cable Type Distance Interface Partcode Fibre 2km Multimode ST LE2122A-R4 Fibre 20km Single-Mode SC LE2122A-SM-R4 Autocross Media Converters Copper 185m Coax LMC210AE 10Mbps Fibre 2km 850-nm Multimode ST LMC212AE-MM-R3 Fibre 2km 850-nm Multimode SC LMC212AE-MM-SC-R2 Fibre 2km 850-nm Multimode ST LMC211AE-MM Fibre 2km 1300-nm Multimode ST LMC211AE-13MM Fibre 5km 1300-nm Multimode ST LMC212AE-13MM-R3 Fibre 15km 1300-nm Single-Mode ST LMC212AE-SM-R3 FlexPoint Modular Media Converters Fibre Fibre 85km 110km 1300-nm Single-Mode SC 1300-nm Single-Mode SC LMC212AE-SM-XLH LMC212AE-SM-SLH 10Mbps 10/100Mbps Fibre Fibre 300m 2km BNC 1300-nm Multimode ST LE6609C-R3 LH6618C PoE PSE Media Converters Fibre Fibre Fibre 2km 2km 15km 1310-nm Multimode SC 1310-nm Multimode ST 1310-nm Single-Mode SC LB1350A-SC/LB1301A-SC LB1302A-SC LB1351A-ST/LB1301A-SC LB1302A-ST LB1350A-SM15 LB1351A-SM15 LB1352A-SM15 MultiLink/ MultiLink II Media Converters Fibre 40km 1310-nm Single-Mode SC LB1350A-SM40 LB1351A-SM40 LB1352A-SM40 Fibre 2km 1300-nm Multimode ST LMC100AE-R2 10/100Mbps Fibre 2km 1300-nm Multimode SC LMC100AE-SC-R2 Fibre 2km 1300-nm Multimode MT-RJ LMC100AE-RJ-R2 Fibre 28km 1300-nm Single-Mode ST LMC100AE-SM-R2 Fibre 28km 1300-nm Single-Mode SC LMC100AE-SMSC-R2 FlexPoint Modular Media Converters Fibre Fibre 28km 58km 1300-nm Single-Mode MT-RJ 1300-nm Single-Mode SC LMC100AE-SMRJ-R2 LMC100AE-SMSC-LH-R2 Fibre 85km 1550-nm Single-Mode SC LMC100AE-SMSC-XLH-R2 Distances not to scale 24 Tech Support: 0118 965 6000 | Sales: 0118 965 6150
AutoCross Media Converters Why worry about the UTP port Let ‘‘the Box’’ figure it out! • Seamless copper-to-fibre conversion for Ethernet or Fast Ethernet. • Easy plug-and-play operation. • Reconfigure themselves for proper UTP cabling — no more crossover cables! • Support for half- and full-duplex operation. • Uplink/downlink fault detection is provided by LinkAlert ! LE2122A-R4 • WARRANTY — Lifetime Connect Ethernet or Fast Ethernet segments to fibre segments without using crossover cables. With BLACK BOX ® AutoCross Media Converters, you no longer have to deal with mismatched transmit and receive cable pairs. These converters contain a switch that senses the type of circuit connected to the UTP port and auto matically configures the port to match. Because the UTP side is autosensing to MDI/MDI-X, you can use either a straight or crossed cable to connect a switch or NIC. The converters feature LinkAlert to monitor for uplink and downlink failures, and alert the network if transmission fails. Use AutoCross Media Converters up to 100 metres on the UTP link, up to 2 kilometres on a multimode fibre link, and up to 20 kilometres on a single-mode fibre link. 10BASE-T versions of the AutoCross Media converter are not compatible with autosensing devices (for example, a 10-/100- Mbps switch); they only work with standard 10-Mbps devices. t E ch spE cs Connectors — LE2122A-R4, LH2001A-ST-R3: (1) RJ-45, (1) pair of ST; LE2122A-SM-R4, LH2001A-SC-R3, LH2001A-SCSM-R3: (1) RJ-45, (1) pair of SC Indicators — LEDs: (1) Power; (1) Link Status and (1) Activity (per each twisted-pair and fibre port) Power — 110–240 VAC, 50–60 Hz, external autosensing power supply Dimensions — 2.5(H) x 7.6(W) x 10.2(D) cm Weight — 0.2 kg Black Box Explains Black Box Explains Guidelines for choosing and testing fibre optic cable. Single-mode or multimode There are two basic types of fibre: multimode and singlemode. both types consist of two basic components: the core and the cladding, which trap the light in the core. typical multimode fibre core diameters are 50, 62.5 and 100 microns. single-mode fibre has a much smaller core, typically 5 to 10 microns. In multimode fibre, multiple photons (or modes of light) travel down the fibre core. However, in long cable runs (greater than 914.4 metres), multiple paths of light can cause signal distortion at the receiving end, resulting in an unclear and incomplete data transmission. In single-mode fibre, the reduced core size allows only a single photon (or one light mode) to travel down the core. Single-mode fibre gives you a higher transmission rate and up to 50 times more distance than multimode, but also costs more. The small core and its single lightwave virtually eliminate any distortion that could result from overlapping light pulses, providing the least signal attenuation and highest transmission speeds of any fibre cable type. Autosensing port configuration! Media Converters Standalone 10Mbps LH2001A-ST-R3 Item Code Price AutoCross Media Converters 10BASE-T to Duplex 10BASE-FL Multimode ST LE2122A-R4 £266.05 Single-Mode SC LE2122A-SM-R4 £498.90 100BASE-TX to Duplex 100BASE-FX Multimode ST LH2001A-ST-R3 £601.31 Multimode SC LH2001A-SC-R3 £601.31 Single-Mode SC LH2001A-SCSM-R3 £1,336.73 Autocross conversion. When using media converters with 10BASE-T or 100BASE-TX cable, you may need to connect your converter to a non-hub device such as a PC or printer, which requires a specially pinned crossover cable for a connection. A media converter with autocross enables you to use an ordinary straight-pinned 10BASE-T patch cable in place of the crossover cable — a manual or automatic switch on the converter makes the crossover connection for you. Autocross conversion eliminates the need to crosspin cables and set an uplink switch. It adapts to the pin assignment of the twisted-pair cable whether it’s crossed or uncrossed. Which fibre to use. • OM1 (62.5/125 μm) — This fibre is now used only used for small networks with no plans for expansion or no data rates higher than Gigabit Ethernet. • OM2 (50/125 μm) — This is now the most popular fibre for networking as it carries much higher bandwidth and can use inexpensive LED transmission systems for running applications up to 622 Mbps (the output is unreadable at faster data rates) as well as VCSEL for short wavelength (850 nm). • OM3 (50/125 μm) — This is the pinnacle of multimode fibre as it carries the highest bandwidth at longer lengths than any other multimode fibre. It's ideal for applications where future network expansion is anticipated. The minor price difference compared with other fibre could be offset by a greater financial savings and fewer network disruptions in the future. • OS1 (9/125 μm) — This fibre is only used in networking in campus/interbuilding backbone applications for distances greater than 550 metres. info@blackbox.co.uk | www.blackbox.co.uk 25
Page 1 and 2: White with 5th black diamond BLACK
Page 3 and 4: Media Converters Introduction Conte
Page 5 and 6: Media Converters Standalone/Chassis
Page 7 and 8: Media Converters Standalone 10 Gbps
Page 9 and 10: Black Box XFP Modules 10 Gigabit mo
Page 11 and 12: Media Converters Standalone 1000Mbp
Page 13 and 14: Multipower Miniature Media Converte
Page 17 and 18: Media Converters Standalone 100Mbps
Page 19 and 20: Crossover Media Converters, 100-Mbp
Page 21 and 22: XS 100-Mbps Media Converter System
Page 23: Media Converters Standalone/Chassis
Page 29 and 30: Modular Media Converters Absolute f
Page 31 and 32: Media Converters Chassis Based Mana
Page 33 and 34: Media Converters Chassis Based Mana

Download PDF - Black Box (UK)

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?