ANSI/SCTE 30 2009

More documents

Recommendations

Info

Card – An integer indicating the Splicer card to which the Server’s insertion multiplex is connected. In cases where the card is labeled alphabetically the translation is made to an integer value (i.e. A – 1; B – 2; etc). Port – The hardware port number where the Server’s insertion multiplex is connected. Logical_Multiplex_Type – A value from the following table. Table 8-3 Logical Multiplex Type 27
Type Bytes Name Description 0x000 0 0x000 1 0x000 2 0x000 3 0x000 4 0x000 5 0x000 6 0x000 7 0 Not Used The Logical_Multiplex field is not needed to identify the multiplex. variabl e User Defined 6 MAC Address 6 IPV4 Address 18 IPV6 Address 5 ATM Address variabl e variabl e IPv4 Address with SPTS Support IPV6 Address with SPTS Support The usage of the Logical_Multiplex field is not defined by this specification and must be agreed upon between the splicer and the server. The Logical_Multiplex field contains the IEEE Media Access Control address of the multiplex as a 6 byte address. The most significant 4 bytes of the Logical_Multiplex field contain the Internet Protocol (IP) address of the multiplex, and the remaining 2 bytes contain the IP port number where the multiplex can be found. The most significant 16 bytes of the Logical_Multiplex field contain the Internet Protocol (IPv6) address of the multiplex, and the remaining 2 bytes contain the IP port number where the multiplex can be found. The Logical_Multiplex field contains the coordinates of the Asynchronous Transfer Mode (ATM) circuit over which the multiplex is carried. The most significant 2 bytes of the logical multiplex field contain the Virtual Path Identifier (VPI) and the next two bytes contain the Virtual Channel Identifier (VCI) of the circuit. The least significant byte contains the ATM Adaptation Layer (AAL) number. See description following this table. See description following this table. 28
Page 1 and 2: ENGINEERING COMMITTEE Digital Video
Page 3 and 4: Table of Contents 1. SCOPE ........
Page 5 and 6: LIST OF FIGURES FIGURE 6-1 SINGLE S
Page 7 and 8: 2.1.2. Normative reference acquisit
Page 9 and 10: Splice-in - The splice at the start
Page 11 and 12: Primary Multiplex (with or without
Page 13 and 14: priority 7 request, the original pr
Page 15 and 16: ChannelName is used for Output Chan
Page 17 and 18: 0x000B GetConfig_Response Splicer C
Page 19 and 20: 7.3.1. Init_Request Message The dat
Page 21 and 22: 7.5. Splice Messages After initiali
Page 23 and 24: ServiceID - The program number of t
Page 25 and 26: Syntax Bytes Type SpliceComplete_Re
Page 27 and 28: SessionID - The SessionID of the cu
Page 29 and 30: SessionID - The SessionID and all s
Page 31: 8. Additional Structures 8.1. Versi
Page 35 and 36: Type 0x0006 - IPv4 Address with Sin
Page 37 and 38: number_of_source_ips - Specifies ho
Page 39 and 40: Table 8-7 time( ) Syntax Bytes Type
Page 41 and 42: 8.5.2. muxpriority_descriptor( ) Fi
Page 43 and 44: Table 8-13 IPV4 port_selection_desc
Page 45 and 46: will probably be required. How the
Page 47 and 48: IPV6_Dest_Address - The destination
Page 49 and 50: PCR to indicate the correct time of
Page 51 and 52: Splicer Server 1) CRM 2) CRespM 3)
Page 53 and 54: NTP Time 3.50 Sec NTP Time 3.50 Sec
Page 55 and 56: 123 Invalid Request Message data( )
Page 57 and 58: Appendix B. Example use of Logical

ANSI/SCTE 30 2009

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?