TIOMOS HINGES - Grass America, Inc.

Full overlay
64 [2 17 /32”]
BPH
Overlay
67 [2 5 /8”]
Half overlay
73.5[2 29 /32”]
Inset
83[3 9 /32”]
19 [ 3 /4”]
DT
84.5 [3 5 /16”]
3.4
Overlay
CC
37
[1 15 /16”]
DD
Reveal
13 [ 1 /2”]
84.5 [3 5 /16”]
DT
37
[1 15 /16”]
0.4 [ 1 /64”] DD
Overlay
CC
10
[ 13 /32”]
Reveal
84.5 [3 5 /16”]
DT
Overlay
CC
6.1
[ 1 /4”]
37
[1 15 /16”]
2x R
3.5[ 1 /8”]
DD
[3 3 /8”]
86
DT
15.6 [ 5 /8”]
CC
6[ 1 /4”]
DD
R
X
Door overlay
Drilling Distance (DD)
3 4 5 6 7 8 9 10
25.0 0
24.0 0
23.0 0 2
22.0 0 2 3
21.0 0 2 3
20.0 0 2 3
19.0 0 2 3
18.5 3.5
18.0 0 2 3
17.5 3.5
17.0 2 3
16.5 3.5
16.0 2 3
15.5 3.5
15.0 3
14.5 3.5
Base Plate Height (BPH)
Door overlay
Drilling Distance (DD)
3 4 5 6 7 8 9 10
22.0 0
21.0 0
20.0 0 2
19.0 0 2 3
18.0 0 2 3
17.0 0 2 3
16.5 3.5
16.0 0 2 3
15.5 3.5
15.0 0 2 3
14.5 3.5
14.0 2 3
13.5 3.5
13.0 2 3
12.5 3.5
12.0 3
11.5 3.5 Base Plate Height (BPH)
Door overlay
Drilling Distance (DD)
3 4 5 6 7 8 9 10
15.5 0
14.5 0
13.5 0 2
12.5 0 2 3
11.5 0 2 3
10.5 0 2 3
10.0 3.5
9.5 0 2 3
9.0 3.5
8.5 0 2 3
8.0 3.5
7.5 2 3
7.0 3.5
6.5 2 3
6.0 3.5
5.5 3
5.0 3.5 Base Plate Height (BPH)
Drawing shows Tiomos with a cranking 03
hinge, Base Plate Height (BPH) 19
X = 38.5 + DT
Drilling Distance (DD)
3 4 5 6 7
0.0 19
0.5
1.0 19
1.5
2.0 19
3.0 19
4.0
Reveal (R)
Base Plate Height (BPH)
Minimum gaps
The minimum gap is the gap between
the closed door and the
front of the cabinet.
*only achievable with 120° angle
reduction clip
Door Thickness
Drilling Distance (DD)
3 4 5 6 7 8 9 10
32.0 1.0 1.0
31.0 1.0 1.0 1.0
30.0 1.0 1.0 1.0
29.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
28.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
26.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
25.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
24.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
22.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
21.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
20.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
18.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
16.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0
Minimum gap
Reveal
Reveal dimensions
were determined with
an edge radius (of
the door) of 1mm!
Hinge dimensions
and reveal calculation
based on factory setting.
IMPORTANT To
determine the correct
application
Grass strongly
recommends a trial
mounting for all hinges
and base plates.
Door Thickness
Drilling Distance (DD)
3 4 5 6 7 8 9 10
32.00.2*0.2*
31.0 0.2*0.2*0.2*0.2*
30.0 0.2 0.2 0.2*0.2*0.2*
29.0 0.2 0.2 0.2 0.2 0.2 0.2*0.2*
28.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
26.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
25.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
24.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
22.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
21.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
20.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
18.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
16.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0 0.0
Reveal (R)
Screw-on
Impresso and Dowelled
Cup dimensions
45
35 +0.1
9.5
39 (40.5)
min. 12.6
39 (40.5)
3 (8)
62 (64.5) ( ) Impresso
Subject to technical modifications without notice. 19