PowerFlex 700 AC Drives

More documents

Recommendations

Info

1-26 Installation/Wiring Lifting/Torque Proving For Lifting/Torque Proving details, refer to page C-4. Using PowerFlex Drives with Regenerative Units If a Regenerative unit (i.e. 1336 REGEN) is used as a bus supply or brake, the common mode capacitors should be disconnected as described in Table 1.E. Connections to the 1336 REGEN Regen Brake Mode Frame(s) Terminals 1336 REGEN PowerFlex 700 0-4 DC+ BR1 DC– DC– 5-6 DC+ DC+ DC– DC– Regenerative Bus Supply Mode Frame(s) Terminals 1336 REGEN PowerFlex 700 0-4 DC+ DC+ DC– DC– 5-6 DC+ DC+ of Common Bus Drives DC– DC– of Common Bus Drives Publication 20B-UM002C-EN-P
Installation/Wiring 1-27 Common Bus/Precharge Notes The following notes must be read and understood. Also refer to pages 1-8 through 1-12 for additional common bus information. Important Application Notes 1. If drives without internal precharge are used (Frames 5 & 6 only), then: a) precharge capability must be provided in the system to guard against possible damage, and b) disconnect switches Must Not be used between the input of the drive and a common DC bus without the use of an external precharge device. 2. If drives with internal precharge (Frames 0-6) are used with a disconnect switch to the common bus, then: a) an auxiliary contact on the disconnect must be connected to a digital input of the drive. The corresponding input (parameter 361-366) must be set to “30, Precharge Enable.” This provides the proper precharge interlock, guarding against possible damage to the drive when connected to a common DC bus. b) the drive must have firmware version 2.002 or above. EMC Instructions CE Conformity Conformity with the Low Voltage (LV) Directive and Electromagnetic Compatibility (EMC) Directive has been demonstrated using harmonized European Norm (EN) standards published in the Official Journal of the European Communities. PowerFlex Drives (1) comply with the EN standards listed below when installed according to this User Manual and the Wiring & Grounding Guidelines Manual. CE Declarations of Conformity are available online at: http://www.ab.com/certification/ce/docs. Low Voltage Directive (73/23/EEC) • EN50178 Electronic equipment for use in power installations. EMC Directive (89/336/EEC) • EN61800-3 Adjustable speed electrical power drive systems Part 3: EMC product standard including specific test methods. (1) 600V class drives below 77A (Frames 0-4) are declared to meet the essential requirements of the Low Voltage Directive. It is the responsibility of the user to determine compliance to the EMC directive. Publication 20B-UM002C-EN-P
Page 1 and 2: PowerFlex 700 AC Drives USER MANUAL
Page 3 and 4: Summary of Changes The information
Page 5 and 6: Table of Contents Preface Overview
Page 7 and 8: Preface Overview The purpose of thi
Page 9 and 10: Overview P-3 Drive Frame Sizes Simi
Page 11 and 12: Overview P-5 Catalog Number Explana
Page 13 and 14: S.M.A.R.T. Exit Lang Auto / Man Rem
Page 15 and 16: Installation/Wiring 1-3 ! ATTENTION
Page 17 and 18: Installation/Wiring 1-5 Fuses and C
Page 19 and 20: Installation/Wiring 1-7 EMC Complia
Page 21 and 22: Installation/Wiring 1-9 Frame 6 Tra
Page 23 and 24: POWER TERMINAL RATINGS WIRE RANGE:
Page 25 and 26: Installation/Wiring 1-13 Terminal D
Page 27 and 28: Installation/Wiring 1-15 Table 1.E
Page 29 and 30: Installation/Wiring 1-17 I/O Wiring
Page 31 and 32: Installation/Wiring 1-19 1 16 32 Fi
Page 33 and 34: J10 Installation/Wiring 1-21 Hardwa
Page 35 and 36: Installation/Wiring 1-23 I/O Wiring
Page 37: Installation/Wiring 1-25 Auto/Manua
Page 41 and 42: Installation/Wiring 1-29 Table 1.J
Page 43 and 44: Chapter 2 Start Up This chapter des
Page 45 and 46: Start Up 2-3 Start-Up Routines The
Page 47 and 48: Start Up 2-5 Running S.M.A.R.T. Sta
Page 49 and 50: Chapter 3 Programming and Parameter
Page 51 and 52: Programming and Parameters 3-3 How
Page 53 and 54: Programming and Parameters 3-5 Adva
Page 55 and 56: Programming and Parameters 3-7 Moni
Page 57 and 58: Programming and Parameters 3-9 File
Page 59 and 60: Programming and Parameters 3-11 Fil
Page 89 and 90:
Programming and Parameters 3-41 Fil
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Programming and Parameters 3-73 Par
Page 123 and 124:
Programming and Parameters 3-75 Par
Page 125 and 126:
Programming and Parameters 3-77 Num
Page 127 and 128:
Chapter 4 Troubleshooting Chapter 4
Page 129 and 130:
Troubleshooting 4-3 Precharge Board
Page 131 and 132:
Troubleshooting 4-5 Fault Decel Inh
Page 133 and 134:
Troubleshooting 4-7 Fault Descripti
Page 135 and 136:
Troubleshooting 4-9 No. Type (1) Fa
Page 137 and 138:
Troubleshooting 4-11 Alarm Dig In C
Page 139 and 140:
Troubleshooting 4-13 Table 4.D Alar
Page 141 and 142:
Troubleshooting 4-15 Drive will not
Page 143 and 144:
Appendix A Supplemental Drive Infor
Page 145 and 146:
Supplemental Drive Information A-3
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
Page 159 and 160:
Page 161 and 162:
Page 163 and 164:
Page 165 and 166:
Page 167 and 168:
Page 169 and 170:
Page 171 and 172:
SHLD SHLD BRAKE TERMINAL RATINGS WI
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
1or3 2 Appendix B HIM Overview For
Page 179 and 180:
HIM Overview B-3 Menu Structure Fig
Page 181 and 182:
HIM Overview B-5 Preferences Menu T
Page 183 and 184:
HIM Overview B-7 Table B.B Linkable
Page 185 and 186:
Appendix C Application Notes For in
Page 187 and 188:
Application Notes C-3 External Brak
Page 189 and 190:
Application Notes C-5 ! ATTENTION:
Page 191 and 192:
Application Notes C-7 8. Start the
Page 193 and 194:
Application Notes C-9 Torque Provin
Page 195 and 196:
Application Notes C-11 Limit Switch
Page 197 and 198:
Application Notes C-13 Torque Produ
Page 199 and 200:
Application Notes C-15 Operation be
Page 201 and 202:
Application Notes C-17 Position Ind
Page 203 and 204:
Application Notes C-19 Profile Comm
Page 205 and 206:
Application Notes C-21 Position Reg
Page 207 and 208:
Application Notes C-23 Figure C.6 H
Page 209 and 210:
Application Notes C-25 Step # [Step
Page 211 and 212:
Application Notes C-27 Power Loss R
Page 213 and 214:
Application Notes C-29 PI Enable Th
Page 215 and 216:
Application Notes C-31 Reverse Spee
Page 217 and 218:
Application Notes C-33 Skip Frequen
Page 219 and 220:
Application Notes C-35 Figure C.17
Page 221 and 222:
Application Notes C-37 only. If “
Page 223 and 224:
Application Notes C-39 Mode Ramp to
Page 225 and 226:
Appendix D Instructions for ATEX Ap
Page 227 and 228:
Instructions for ATEX Approved Driv
Page 229 and 230:
Page 231 and 232:
Page 233 and 234:
Index A AC Input Circuit Breakers,
Page 235 and 236:
Index-3 by Name, 3-72 by Number, 3-
Page 237 and 238:
Index-5 Fdbk Filter Sel, 3-15 Feedb
Page 239 and 240:
Index-7 Min Adj Voltage, 3-63 Min R
Page 241 and 242:
Index-9 Dyn UserSet Actv, 3-37 Dyn
Page 243 and 244:
Index-11 TorqProve Cnfg, 3-59 TorqP
Page 245 and 246:
Index-13 Speed Ref B Sel, 3-19 Spee
Page 247 and 248:
1 PowerFlex 700 Parameter Record Nu
Page 250:
U.S. Allen-Bradley Drives Technical
show all

PowerFlex 700 AC Drives

Create successful ePaper yourself

Delete template?

Save as template?