PowerFlex 700 AC Drives
PowerFlex 700 AC Drives
PowerFlex 700 AC Drives
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
2-4 Start Up<br />
Figure 2.2 Start Up Menu<br />
Basic<br />
Done /<br />
Exit<br />
Start-Up Continue<br />
Start Over<br />
Intro<br />
Selection:<br />
1. SMART<br />
2. Basic<br />
3. Detailed<br />
4. Application<br />
Motor Control<br />
Select<br />
Configures<br />
Motor Control<br />
Method<br />
Selection:<br />
1. Torq Prove<br />
2. Pos/Spd Profile<br />
3. Oil Well Pumps<br />
Motor Data and<br />
Ramp Times<br />
Enter Motor NP<br />
Data, Stop Mode,<br />
Accel/Decel<br />
Ramp Times<br />
Motor Tests (1) Set Min/Max<br />
Optimize Torque<br />
and<br />
Verify Direction<br />
Speed Limits<br />
Speed and<br />
Direction Control<br />
Speed/Torque<br />
Control<br />
Configure<br />
Source, Value<br />
and Scale for<br />
Speed References<br />
Start/Stop/I/O<br />
Configure<br />
Control Method<br />
(2 Wire/3 Wire),<br />
I/O, Digital I/O<br />
& Analog Outputs<br />
Pos/Spd Profile<br />
Pos/Spd Profile<br />
Detailed<br />
Application<br />
Configure for a<br />
Specific Application<br />
such as; Auto Restart,<br />
Flying Start, etc.<br />
Done /<br />
Exit<br />
Done /<br />
Exit<br />
Motor Control<br />
Select<br />
Configures<br />
Motor Control<br />
Method<br />
Motor Data and<br />
Ramp Times<br />
Enter Motor NP<br />
Data, Stop Mode,<br />
Accel/Decel<br />
Ramp Times<br />
Motor Tests (1) Set Min/Max<br />
Optimize Torque<br />
and<br />
Verify Direction<br />
Speed Limits<br />
Speed and<br />
Direction Control<br />
Torq Proving<br />
Speed/Torque<br />
Control<br />
Configure<br />
Source, Value<br />
and Scale for<br />
Speed References<br />
Torq Proving<br />
Done /<br />
Exit<br />
Well Pump<br />
Type<br />
Motor Data and<br />
Ramp Times<br />
Pump Data Start/Stop/I/O<br />
Motor Tests (1)<br />
Speed/Torque<br />
Control<br />
Torque Alarm Process Display Done /<br />
Exit<br />
Enter Motor NP<br />
Data, Stop Mode,<br />
Accel/Decel<br />
Ramp Times<br />
Enter Pump<br />
Data<br />
Configure<br />
Control Method<br />
(2 Wire/3 Wire),<br />
I/O, Digital I/O<br />
& Analog Outputs<br />
Optimize Torque<br />
and<br />
Verify Direction<br />
Configure<br />
Source, Value<br />
and Scale for<br />
Speed References<br />
(1) During Motor Tests and tuning procedures, the drive may modify certain parameter values for proper Start Up operation. These values are then reset to their original<br />
values when Start Up is complete. The affected parameters are: 053, 080, 276, 278 and 361-366. If power is removed from the drive during the tests without aborting<br />
the auto-tune procedure, these parameters may not be reset to their original value. If this situation occurs, reset the drive to factory defaults and repeat the Start Up<br />
procedure.<br />
Publication 20B-UM002C-EN-P
Change language