PCL 5 Color Technical Reference Manual - Business Support ...

More documents

Recommendations

Info

Setting Description MapID Device-Independent No Cluster-No Adjust-DI 51 Adjustment Disperse-No Adjust-DI 52 Scatter-No Adjust-DI 53 ErrorDiffusion-No Adjust-DI 54 Process Blue Cluster-Process Blue-DI 55 Disperse-Process Blue-DI 56 Scatter-Process Blue-DI 57 ErrorDiffusion-Process Blue-DI 58 Transparency Cluster-Transparency-DI 59 Disperse-Transparency-DI 60 Scatter-Transparency-DI 61 ErrorDiffusion-Transparency-DI 62 Vivid Cluster-VividGraphics-DI 63 Graphics Disperse-VividGraphics-DI 64 Scatter-VividGraphics-DI 65 ErrorDiffusion-VividGraphics-DI 66 Out of Gamut Cluster-OutOfGamut-DI 67 Disperse-OutOfGamut-DI 68 Scatter-OutOfGamut-DI 69 ErrorDiffusion-OutOfGamut-DI 70 CIELab Match Cluster-TrueMatch-DI 71 Disperse-TrueMatch-DI 72 Scatter-TrueMatch-DI 73 ErrorDiffusion-TrueMatch-DI 74 D-26 Modifying Output Color (Color LaserJet, 5, 5M, DeskJet) EN
Index A adaptive compression block size 6-28, 6-31 compression methods 6-29 control bytes 6-29 cursor position 6-31 data block 6-28 delta row 6-29, 6-31 duplicate row 6-29, 6-30, 6-31 empty row 6-29, 6-30, 6-31 format 6-29 operation hints 6-31 row length 6-31 run-length encoded 6-29, 6-31 seed row 6-31 TIFF 6-29, 6-31 y-offset 6-31 area fill ID command See also pattern ID command 5-29 area fill, user-defined patterns 5-33 assign color index command 3-20, C-21 B base pattern 5-33 black and white references A-4 black rule 5-32 black-and-white mode 2-1, B-2 block size, adaptive compression 6-28 byte counts 6-34 C chapter summary iv CIE L*a*b* color space B-18 clipping raster area 6-13 coding efficiency, raster compression 6-23 color concepts A-3 device-dependent A-2, A-4, A-10 device-independent A-2, A-4, A-10 foreground 3-17, C-18 lookup tables A-12, D-13 map 4-4, D-22 matching A-11 modes A-7 modifying output 4-1, D-1 processing documents A-14 raster vs. non-raster A-3, A-14 selection A-5 color appearance matching A-12 color component one command 3-19, C-20 color component three command 3-20, C-21 color component two command 3-19, C-20 color lookup tables A-2 color lookup tables command D-13 color management 1-4 color modes black-and-white mode 2-1, B-2 HP-GL/2 imaging mode 2-2, 2-13, B-3, B-28 PCL imaging mode 2-2, 2-5, B-2, B-6 simple color mode 2-1, 2-3, B-2, B-4 color print model command sequence 5-6 logical operations and transparency 5-12 rectangular area fills 5-45 color printing overview 1-1, A-1 color range (CR) command 7-19 color selection and palettes 1-6 color spaces 1-3 color specifications 1-3 color vector graphics (HP-GL/2) 7-1 Colorimetric RGB color space B-20 command finish mode 4-6 logical operation 5-13 pixel placement 5-27 commands, PCL ?*c#G - Pattern (Area Fill) ID 5-29 End Raster Graphics 6-35 pattern control 5-44 pattern ID 5-29 pattern transparency mode 5-8 raster graphics presentation 6-10 raster graphics resolution 6-8 raster graphics, start 6-17 Raster Height command 6-13 Raster Width command 6-15 raster y offset 6-19 Select Current Pattern command 5-32 Set Pattern Reference Point 5-43 Set Raster Compression Method 6-20 Source Transparency Mode 5-7 EN Index-1
Page 3 and 4:
PCL 5 Color Technical Reference Man
Page 5 and 6:
Inside This Manual What You Can Lea
Page 7 and 8:
Chapter 7. Color Vector Graphics (H
Page 9 and 10:
Contents PCL 5 Color Technical Refe
Page 11 and 12:
Rectangular Fill Examples. . . . .
Page 13 and 14:
Programming Color Palettes . . . .
Page 15 and 16:
1 Color Printing Overview Introduct
Page 17 and 18:
The PCL language also allows users
Page 19 and 20:
Note HP’s ICC profiles are availa
Page 21 and 22:
� An RGB, eight-entry palette wit
Page 23 and 24:
Well-Behaved Raster PCL raster imag
Page 25 and 26:
2 Using Color Modes Introduction Th
Page 27 and 28:
Simple Color Mode The Simple Color
Page 29 and 30:
PCL Imaging Mode The PCL Imaging mo
Page 31 and 32:
Byte 1 (Pixel Encoding Mode) This b
Page 33 and 34:
PEM 1: INDEXED BY PIXEL In this mod
Page 35 and 36:
MODE 3: DIRECT BY PIXEL This mode s
Page 37 and 38:
HP-GL/2 Imaging Mode The HP-GL/2 Im
Page 39 and 40:
3 Using Palettes Introduction A pal
Page 41 and 42:
Saving the Palette The current pale
Page 43 and 44:
Palette Management by ID All palett
Page 45 and 46:
When a palette creation command is
Page 47 and 48:
Palette Control The Palette Control
Page 49 and 50:
Simple Color Palettes The Simple Co
Page 51 and 52:
CID Color Palettes The Configure Im
Page 53 and 54:
HP-GL/2 Palettes Regardless of the
Page 55 and 56:
Foreground Color All PCL marking en
Page 57 and 58:
Programming Color Palettes Except f
Page 59 and 60:
4 Modifying Output Color Introducti
Page 61 and 62:
Monochrome Printing The Monochrome
Page 63 and 64:
Screen Match Due to the emergence o
Page 65 and 66:
5 The PCL Print Model Introduction
Page 67 and 68:
Pattern Transparency Mode—The tra
Page 69 and 70:
Figure 5-3 Effect of Transparency M
Page 71 and 72:
Source Transparency Mode Command Th
Page 73 and 74:
Logical Operations The basic print
Page 75 and 76:
Assuming three bits per pixel, the
Page 77 and 78:
Logical Operation Command Specifies
Page 79 and 80:
Table 5-1. RGB ROP Truth Tables ROP
Page 81 and 82:
Note Since PCL logical operations a
Page 83 and 84:
Table 5-4. Logical Operations (ROP3
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Figure 5-5 Pixel Placement Note The
Page 91 and 92:
Pixel Placement Command Determines
Page 93 and 94:
Pattern ID (Area Fill ID) Command T
Page 95 and 96:
Figure 5-8 Cross-Hatch Patterns EN
Page 97 and 98:
User-Defined Pattern Graphics In ad
Page 99 and 100:
Figure 5-10 Pattern Layout Across t
Page 101 and 102:
Figure 5-11 Moving Pattern Referenc
Page 103 and 104:
Continuation (Byte 1) This field, b
Page 105 and 106:
When using the 300 dpi User-Defined
Page 107 and 108:
Set Pattern Reference Point Command
Page 109 and 110:
Rectangular Area Fills (Rules) Rect
Page 111 and 112:
Vertical Rectangle Size (PCL Units)
Page 113 and 114:
Note The current pattern is not app
Page 115 and 116:
This example is a monochrome exampl
Page 117 and 118:
7 Select the white fill and print.
Page 119 and 120:
5 Print the rectangular shaded area
Page 121 and 122:
6 Raster Graphics Introduction A ra
Page 123 and 124:
This pixel format is sufficient to
Page 125 and 126:
An image’s width and height defin
Page 127 and 128:
The emphasis in the previous comman
Page 129 and 130:
Figure 6-2 Raster Graphics Expansio
Page 131 and 132:
Raster Presentation Mode Orientatio
Page 133 and 134:
Source Raster Height Command The Ra
Page 135 and 136:
Source Raster Width Command The Ras
Page 137 and 138:
Start Raster Graphics Command The S
Page 139 and 140:
Raster Y Offset Command The Raster
Page 141 and 142:
The Set Compression Mode command ha
Page 143 and 144:
Note Another method to calculate th
Page 145 and 146:
The command byte identifies two thi
Page 147 and 148:
The seed row is updated by every ra
Page 149 and 150:
The size of a block is limited to 3
Page 151 and 152:
Adaptive Compression Operation Hint
Page 153 and 154:
Transfer Raster Data by Plane This
Page 155 and 156:
End Raster Graphics Command The End
Page 157 and 158:
Destination Raster Width The Destin
Page 159 and 160:
8 Specify the raster compression mo
Page 161 and 162:
Figure 6-7 Example of Raster Graphi
Page 163 and 164:
Looking at the PCL commands, you'll
Page 165 and 166:
7 Color Vector Graphics (HP-GL/2) I
Page 167 and 168:
� The ?%#A command closes HP-GL/2
Page 169 and 170:
Redefining the PCL Picture Frame si
Page 171 and 172:
Opcode — Specifies the logical op
Page 173 and 174:
Page 175 and 176:
Page 177 and 178:
Page 179 and 180:
The “PC;” command defaults the
Page 181 and 182:
NP (Number of Pens) The NP command
Page 183 and 184:
CR (Color Range) The CR command set
Page 185 and 186:
Figure 7-1 Pixel Placement EN Color
Page 187 and 188:
A Color Printing Overview (Color La
Page 189 and 190:
Color Concepts This section describ
Page 191 and 192:
Example: Assuming the white and bla
Page 193 and 194:
Encoding by Pixel When encoding by
Page 195 and 196:
Cluster Ordered Dither ( ?*t7J, ?*t
Page 197 and 198:
With proper calibration, any device
Page 199 and 200:
Illumination Models Illumination so
Page 201 and 202:
Color Processing Functions Given th
Page 203 and 204:
B Using Color Modes (Color LaserJet
Page 205 and 206:
HP-GL/2 Imaging Mode In HP-GL/2, th
Page 207 and 208:
The Simple Color palettes are shown
Page 209 and 210:
Common 6-Byte Header The short and
Page 211 and 212:
You need one plane or one bit/pixel
Page 213 and 214:
Example: ?*v6W 00 01 04 04 04 04 #
Page 215 and 216:
Example: ?*v6W 00 03 00 08 08 08 #
Page 217 and 218:
Short Form of CID Command (Configur
Page 219 and 220:
Long Form of CID Command (Configure
Page 221 and 222:
Note Although the data ranges may e
Page 223 and 224:
Byte 15 (msb) 8 7 (lsb) 0 Byte 22 x
Page 225 and 226:
Byte 15 (msb) 8 7 (lsb) 0 Byte 22 E
Page 227 and 228: Examples Using the CID Command The
Page 229 and 230: LONG FORM CID(2,3,0,8,8,8 0.62, 0.3
Page 231 and 232: C Using Palettes (Color LaserJet, 5
Page 233 and 234: Saving the Palette The current pale
Page 235 and 236: Palette Management by ID All palett
Page 237 and 238: This command can be used to de-sele
Page 239 and 240: Palette Control The Palette Control
Page 241 and 242: Simple Color Palettes The Simple Co
Page 243 and 244: CID Color Palettes The Configure Im
Page 245 and 246: Device CMY and Device-Independent P
Page 247 and 248: Eight Pens Pen Number Color 0 White
Page 249 and 250: Note Foreground color interacts wit
Page 251 and 252: Color Component Three This command
Page 253 and 254: D Modifying Output Color (Color Las
Page 255 and 256: Halftone Render Algorithms The HP c
Page 257 and 258: Ordered Dither and Clustered Ordere
Page 259 and 260: A user-defined matrix is defined in
Page 261 and 262: Format This byte should be set to 0
Page 263 and 264: Byte 15 (msb) 8 7 (lsb) 0 Byte 0 Fo
Page 265 and 266: Color Lookup Tables Color lookup ta
Page 267 and 268: As shown below, the 256 point-by-po
Page 269 and 270: Gamma Correction Color monitors, wh
Page 271 and 272: The PCL default viewing illuminant
Page 273 and 274: Driver Configuration Command This c
Page 275 and 276: No Adjustment This setting provides
Page 277: Setting Description MapID Out of Ga
Page 281 and 282: transparency mode 5-2 user-defined
Page 283 and 284: Set Pattern Reference Point command
show all

PCL 5 Color Technical Reference Manual - Business Support ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?