PRIMERGY RX200 S3

PRIMERGY RX200 S3 

System configurator and order-information guide 

May 2008 

Contents 

Instructions 

Configuration 

diagram 

Configurator 

0 System software 

I Basic unit 

I I I Processor 

I I I Memory 

I V Riser Card 

V 

Graphics 

VI Accessible drives 

VII Hard disk drives 

V I I I SCSI controller 

I X Fibre-Channel controller 

X Disk array 

X I Communication/Network 

X I I System Management Products (RemoteView) 

X I I I Miscellaneous 

X I V Country specific power cord 

Change 

report 

PRIMERGY Server


PRIMERGY RX200 S3 Status 2008-04-28 

Instructions 

This document contains basic product and configuration information that will enable you to configure your system via 

PC-/System-Architect 

Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete 

P R I M E R G Y R a c k s y s t e m . 

You can configure your individual PRIMERGY server in order to adjust your specific requirements. 

The System configurator is divided into several chapters that are identical to the current price list and PC-/System-Architect. 

Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through 

the configurator by following the lines from the top to the bottom. 

Section III Memory, example 

There are X memory slots which can be equipped with XXX MB 

It is permissible to make up to X passes through the memory upgrade options 

X 

times 

S26361-XXX-XXX 

S26361-XXX-XXX 

Memory XXX MB Memory XXX MB 

max. X times per system max. X times per system 

In one chapter you can only select as many components (here 4x) as the arrow indicates. 4x 

Please note that there are information symbols which indicate necessary information. 

Further information in the internet see: 

http://www.primergy.com 

http://extranet.fujitsu-siemens.com/primergy 

(internet) 

(extranet) 

Prices and availability see price list and PC-/System-Architect. 

Subject to change and errors excepted. 

Fujitsu Siemens Computers 

Enterprise Products PRIMERGY Server 2 of 22



Configuration diagram PRIMERGY RX200 S3 

System unit ( I ) 

board front side 

Channel 0 (2 Modules) 

Xeon 

DP 

Channel I (2 Modules) Air channel 

right 

Channel II (2 Modules) 

Xeon DP Bay for 5,25"x 0,5" IDE-CD 

Channel III (2 Modules) or DVD-ROM 

Memory ( III ) Processor ( II ) 

Accessible drives ( V ) 

Hard disk drives ( VI ) 

rear side left side 

1 . P S U 2 . P S U Double Fan 

1 - 5 3.5"x1" SAS or SATA 

Redundant PSU fans Redundant system- 

Fan 1 Fan 2 Fan 3 fans 3.5"x1" SAS or SATA 

Redundant power 

supply option 

3.5" HDD bays option 

RAID 1(E) support 

on-board 

Extension slots for 

left 

side 

SCSI Controller ( VIII ) 2.5"x1" SAS or SATA 

Disk Array ( X ) 

Communication/Network ( XI ) 

System Management ( XII ) 

Miscellaneous ( X ) 2.5"x1" SAS or SATA 

Slot 1: PCI-X 64 Bit / 100 MHz, Low Profile 2.5"x1" SAS or SATA 

2.5" HDD bays option 

Slot 2: PCI-X 64-Bit / 133MHz, 2.5"x1" SAS or SATA 

Standard Profile or Low Profile 

Slot 2: PCIe x8 

Standard Profile or Low Profile 

riser options 

Key: 

Included in basic unit 

Option 




Start PRIMERGY RX200 S3 PRIMERGY RX200 S3 Status 2008-04-28 

SW Configurator 32 bit 

with OEM-Software 

without OEM-Software 

for PRIMERGY Server for PRIMERGY Server 

OEM-SW is bound to HW and 

VMware-Software is not allowed to be ordered 

- VCMS VirtualCenter Management Server separately. 

- Virtual Infrastructure 3 Exception: VMware SW 

For all SW products please refer to the corresponding software configurator accessible via 

the Extranet under Configuration & Tools, -All configurations, -Software, URL see below. 

Microsoft - Software: W **) PRIMECLUSTER *) 

- Windows Server 2003 R2, - Clustering 

Standard Edition - Load Balancing 

Enterprise 

Edition 

! Web Edition, SP2/English 

- Additional loose Linux - Software **) 

Client-Access-Licenses (CALs) - Open Enterprise Server ***) 

(not for Web Edition) - SuSE Linux ES (OEM): LO 

- SuSE Linux ES (Support): LS 

- Red Hat EL (OEM): LO 

- Red Hat EL (Support): LS 

DuplexDataManager & MultiPath 

W2K3; Linux 

Manageability Software: V**) 

- IRMC advanced Pack 

- RemoteDeploy 

- RemoteView SW Details eg. version numbers are published 

- Altiris Server Deployment in the separate SW-Configurator 

Backup-Software / 

*) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under 

http://extranet.fujitsu-siemens.com/primecluster 

Application-Software: U 

- ARCserve **) Pay attention to release and order information in PRINCE -> Operating System 

- openSM2 http://vil.mch.fsc.net/vil/pc/vil/primergy/overview/prince/index_en.htm 

***) Supply over distribution or procurement from FSC VP BC Software 

They find single software configurators and release lists (OS-matrix / system management / security) under following addresses: 

for internal users: 

for partners: 

http://vil.mch.fsc.net/vil/oec/special/primergy/index_en.htm 

http://vilpart.fujitsu-siemens.de/vil/oec/special/primergy/index_en.htm 

Continue with PRIMERGY 

HW configurator 





SW Configurator EM64T 

with OEM-Software 

without OEM-Software 

for PRIMERGY Server for PRIMERGY Server 

OEM-SW is bound to HW and 

VMware-Software is not allowed to be ordered 

- VCMS VirtualCenter Management Server separately. 

- Virtual Infrastructure 3 Exception: VMware SW 

For all SW products please refer to the corresponding 

software configurator accessible via the Extranet under 

"Configuration & Tools, -All configurations, -Software, 

URL see below. 

Microsoft - Software: W Linux - Software *) **) 

only - Windows Server 2003 R2, only - SuSE Linux ES (OEM): LO 

EM64T Standard x64 Edition x86_64 - SuSE Linux ES (Support): LS 

Enterprise x64 Edition - Red Hat EL (OEM): LO 

- Additional loose - Red Hat EL (Support): LS 

Client-Access-Lizenzen 

(CALs) 

only MultiPath, Duplex Data 

EM64T Manager (DDM) 

Windows, Linux (W-DDM) 

Manageability Software: V**) 

only - RemoteDeploy 

EM64T - RemoteView SW 

Details eg. version numbers are published 

in the separate SW-Configurator 

*) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under 

http://extranet.fujitsu-siemens.com/primecluster 

**) Pay attention to release and order information in PRINCE -> Operating System 

http://vil.mch.fsc.net/vil/pc/vil/primergy/overview/prince/index_en.htm 

You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses: 

for internal users: 

for partners: 

http://vil.mch.fsc.net/vil/oec/special/primergy/index_en.htm 

http://vilpart.fujitsu-siemens.de/vil/oec/special/primergy/index_en.htm 

Continue with PRIMERGY 

HW configurator 





Section I Basic unit 

System unit consisting of: 

* 1U Housing including 

- hot plug Power supply unit with 1 PSU module and power cord rack 4m lenght 

(can be upgraded with one additional PSU module) 

* Fans 

- Redundant power supply fans 3x) 

- Redundant and hot plug system fans (5x) 

* Drives / Bays 

- 1 bay for 4x 2.5" SAS HDD or 2x 3.5" SAS HDD option 

- 1 bay IDE-CD- or DVD-ROM 0,5" height (option) 

* Integrated ServerView Diagnostics Technology for indication of internal failed components 

Systemboard with: 

* One Xeon Dual- or Quad-Core CPU supporting 64Bit EM64T and Intel® VT / HT / DBS Technology. 

- ( VT =Virtualisation Technology, HT = Hyper Threading, DBS = Demand Based Switching ) 

* Chipset Intel® 5000P (codenamed Blackford) 

* 2 PCI slots (configuration dependend on choosen riser option): 

-1x PCIe x8 (standard and Low Profile cards) and 1x PCI-X 64Bit/100MHz (Low Profile cards only) 

-1x PCI-X 64Bit/133MHz (standard and Low Profile cards) and 1x PCI-X 64Bit/100MHz (Low Profile cards only) 

* 8 memory slots for max. 32GB RAM ( Fully Buffered DIMM = FBD533 / PC2-4200F ) available 

- Memory is divided into two branches, driven by a memory controller each. 

- Each branch has 2 channels with 2 DIMM slots each (bank 1 and bank 2) 

- Max. 4GB modules per slot are possible 

- Memory upgrade is possible per branch with modul pairs ( one pair / branch ) 

- Memory mirrroring is supported branch to branch for 2 identical module pairs each in the same 

same memory bank of branch 0 and branch 1 

- Max. memory bandwidth and 4-way interleaving is supported with 2 identical memory pairs 

in one memory bank (one pair per branch) if mirroring is disabled 

- SDDC (Chipkill) is supported for memory modules, 

* One Fast-IDE (ATA) channel on-board for 1x DVD integrated in the 

Intel Southbridge ESB2-V 

* 8-channel SAS controller (LSI 1068) on-board including 

IME (Integrated Mirroring Enhanced) offering the RAID level 0, 1 & 1E without any additional costs. 

* 2* Gbit Ethernet LAN BroadCom 5715 on-board 

* iRMC (integrated Remote Management Controller) on-board server management and graphics controller 

Resolution: 1280 x 1024 at 8bpp or 1024 x 768 at 16 bpp 

Interfaces: 

* 1x RS-232-C (serial, 9 pins) (usable for BMC or OS or shared) 

* 1x keyboard (PS/2) 

* 1x mouse (PS/2) 

* 1x VGA (15 pins) 

* 4x USB 2.0 ( UHCI ) with 480MBit/s (2x external at the rear, 2x external at the frontside, no USB wakeup) 

* 2x LAN RJ45 

Cables: 

1. IDE cable for CD/DVD. 

2. SAS cables for up to 4 internal hot plug HDDs 

3. Power cable 

Software: 

- ServerView Suite Software package incl. ServerStart, ServerBooks, Management Software and Updates 

- Documentation engl. (multilingual on CD) 

Mounting kit for PRIMERGY RX200 S3 is part of the basic unit 

- 1 pair of telescopic rails 

- 1 Vario carrier DC-PC-3rd party Rack 

allows toolless adjustable in depth and easy mounting 

Mounting kit for mounting of servers in in FSC 19" PRIMECENTER- racks 

and all server racks conforming to EIA standard EIA-310-D for 19" racks. 

Therefore the mounting kit is variable in depth from 704-790mm 

Cables included in basic unit 

Connections Cable PRIMERGY RX200 S3 Key: 

¥ S A S 

1. IDE CD/DVD ◦ ◦ ◦ IDE 

2. SAS cables HDDs ¥ ¥ 

3. Power cable 

A 




A PRIMERGY RX200 S3 Status 2008-04-28 

* while stocks last 

Rack version for 19'' racks with 

1 hot plug power supply module 

Basic unit with 

- 1x Xeon DP (4MB shared SLC ) Dual-Core Processor 

with 1066/1333MHz Frontside Bus (max. 2) 

Xeon DP 5110 (1.66GHz/4M/1066) S26361-K995-V211 * 

Xeon LV DP 5148 (2.33GHz/4M/1333) S26361-K995-V244 * 



Basic unit with 

- 1x Xeon DP (2x4MB shared SLC ) Quad-Core Processor 

with 1066/1333MHz Frontside Bus (max. 2) 

Xeon DP E5310 (1.60GHz/2x4M/1066) S26361-K995-V501 * 

Xeon LV DP L5310 (1.60GHz/2x4M/1066) S26361-K995-V511 * 






Xeon DP X5355 (2.66GHz/2x4M/1333) S26361-K995-V506 * 

Xeon DP X5365 (3.00GHz/2x4M/1333) S26361-K995-V507 * 

S26113-F509-E1 

For later conversion the following kit is available: 

2nd redundant PSU module 1.) 1 power supply module hot plug S26113-F509-L1 

for redundancy incl. power cord 

uses hot plug PSU slot 

max. 1x per system 

PRIMERGY Rack 

S26361-F1647-E302 

Installation ex works for one 

PRIMERGY 42/23U rack 

server or subsystem. 

PRIMERGY Classic 19" rack is not supported 

Hereby the rack will be delivered 

completely pre-mounted and 

all wired connections are tested. 

With racks 12U, 24U, 38U: 

Systems and components 

will be delivered installed in the rack 

With racks 46U: "Rack-mounting ex factory" 

Systems and components This service is to be ordered once 

will be delivered separately per installable server/storage 

To be ordered only together with subsystem, in order to get the 

a PRIMERGY PRIMECENTER rack server/storage subsystem 

mounted into the PRIMERGY racks. 

e . g . : In case of the 46 U PRIMERGY Rack, 

S26361-K826-V10x 

this service has to be ordered, 

refer configurator PC-Rack 

to get the mounting kits and the 

max. 1x per System cables installed. 

B 




B PRIMERGY RX200 S3 Status 2008-04-28 

Section II Processor 

There are 2 processor LGA771 sockets available. 

It is also possible to upgrade a dual-processor system later on. 

Two processors with different clock frequencies are not possible 

A multi-processor operating system is required for a dual-processor system. 

2. CPU 

S26361-F3323-E160 

64-bit Intel Xeon DP 5110 

1.6GHz/1066MHzFSB 

with 4 MB SLC on Chip 

(SLC=Second Level Cache) 

and passive heat sink 

occupies socket for one CPU 


S26361-F3323-E433 S26361-F3323-E266 S26361-F3323-E300 S26361-F3349-E160 

64-bit Intel Xeon LV DP 5148 64-bit Intel Xeon DP 5150 64-bit Intel Xeon DP 5160 64-bit Intel Xeon DP E5310 

2.33GHz/1333MHz FSB 2.66GHz/1333MHzFSB 3.00GHz/1333MHzFSB 1.60GHz/1066MHz FSB 

with 4MB SLC on Chip with 4 MB SLC on Chip with 4 MB SLC on Chip 2x4MB shared SLC on Chip 

(SLC=Second Level Cache) (SLC=Second Level Cache) (SLC=Second Level Cache) (SLC=Second Level Cache) 

and passive heat sink and passive heat sink and passive heat sink and passive heat sink 

occupies socket for one CPU occupies socket for one CPU occupies socket for one CPU occupies socket for one CPU 

max. 1x per system max. 1x per system max. 1x per system max. 1x per System 

S26361-F3349-E460 S26361-F3349-E186 S26361-F3349-E486 S26361-F3349-E200 

64-bit Intel Xeon LV DP L5310 64-bit Intel Xeon DP E5320 64-bit Intel Xeon LV DP L5320 64-bit Intel Xeon DP E5335 

1.60GHz/1066MHz FSB 1.86GHz/1066MHz FSB 1.86GHz/1066MHz FSB 2.00GHz/1333MHz FSB 

2x4MB shared SLC on Chip 2x4MB shared SLC on Chip 2x4MB shared SLC on Chip 2x4MB shared SLC on Chip 




max. 1x per system max. 1x per System max. 1x per system max. 1x per system 

S26361-F3349-E400 S26361-F3349-E233 S26361-F3349-E266 S26361-F3349-E300 

64-bit Intel Xeon LV DP L5335 64-bit Intel Xeon DP E5345 64-bit Intel Xeon DP X5355 64-bit Intel Xeon DP X5365 

2.00GHz/1333MHz FSB 2.33GHz/1333MHz FSB 2.66GHz/1333MHz FSB 3.00GHz/1333MHz FSB 

2x4MB shared SLC on Chip 2x4MB shared SLC on Chip 2x4MB shared SLC on Chip 2x4MB shared SLC on Chip 




max. 1x per system max. 1x per system max. 1x per system max. 1x per system 

C 




C PRIMERGY RX200 S3 Status 2008-04-28 

Section III Memory 

- There are 8 memory slots for max. 32GB RAM ( Fully Buffered DIMM = FBD533 / PC2-4200F ) available 

( For explanation of following terms refer to section "Memory Configurations" 

- The memory area is divided into 2 branches with 2 channels each and 2 slots per channel 

- The first slot of each channel belongs to memory bank 1, the second slot belongs to memory bank 2 

- Each slot can optionally be equipped with 512MB, 1GB, 2GB or 4GB FBDIMM modules 

No mix of modules within one memory branch of bank1 or bank2 allowed. 

- Memory upgrade is only possible per branch with modul pairs 

( one pair per branch, max. two pairs / branch). 

- For each basic unit bank 1 of the first branch has to be equipped with one memory pair, 

which has to be ordered with the ordercode of a "Base Memory" 

(either 2x512MB = 1GB, 2x1GB = 2GB, 2x2GB = 4GB or 2x4GB = 8GB) 

Note**: The price of the smallest 1GB FBD533 Base Memory is already included in the basic unit, 

The price of the other Base Memories is the Delta to the smallest 1GB FBD533 Base Memory 

So additional memory extensions (Upgrade Memory ) can still be configured up to three times 

for the standard market price. 

- For the function Memory Mirroring two identical memory module pairs regarding capacity 

are necessary in each branch of one memory bank. So following memory has to be ordered: 

1.) Minimum one time the same capacity like already is preinstalled in the basic unit has to be ordered 

2.) For additional memory 2x the same capacity has to be ordered 

- 4-way memory interleave technology for maximum performance is possible with 

2 memory module pairs in one memory bank (one pair per branch ) 

- ECC with SDDC (Chipkill) is standard for RX200 S3. 

For a description of memory configurations refer to section "Memory Configurations" 

See Note** above 

S26361-F3313-B521 S26361-F3313-B522 S26361-F3313-B523 S26361-F3313-B524 

Base Memory 1GB Base Memory 2GB Base Memory 4GB Base Memory 8GB 

FBD533 / PC2-4200F FBD533 / PC2-4200F FBD533 / PC2-4200F FBD533 / PC2-4200F 

consisting of consisting of consisting of consisting of 

2 single rank modules 2 dual rank modules 2 dual rank modules 2 dual rank modules 

occupies one branch occupies one branch occupies one branch occupies one branch 

1x per system 1x per system 1x per system 1x per system 

1x 

S26361-F3230-B521 S26361-F3230-B522 S26361-F3230-B523 S26361-F3230-B524 

Base Memory 1GB Base Memory 2GB Base Memory 4GB Base Memory 8GB 





1x per system 1x per system 1x per system 1x per system 

D 




D PRIMERGY RX200 S3 Status 2008-04-28 

For the Memory Mirroring mode two identical memory modules pairs (branch 0 & 1) are necessary. 

( bank1 of branch 0 and 1 contain identical memory pairs ) 

Therefore the following upgrade memory has to be ordered additionally: 

1.) Minimum one time the same capacity like the selected Base Memory of the basic unit = 

2.) For addtitional memory 2x the same capacity = 

The function Memory Mirroring can be configured per BIOS setup. 

For mirrored memory configurations the following items have to be considered: 

Capacity: 50% of the configured memory 

Availability: Maximum memory availability 

After non-correctable errors or too many correctable errors 

the Mirror takes over immediately and the system remains online. 

Performance: 2-way interleave only in mirror configurations, 

therefore potentially not max. performance 

In general it is recommended to use identical capacities over the branches / channels, 

regarding bank1 and bank 2 to ensure max. performance bandwidth. = = = 

bank 2 

FB-DIMM FB-DIMM FB-DIMM FB-DIMM 

bank 1 

FB-DIMM FB-DIMM FB-DIMM FB-DIMM 

channel 0 channel 1 channel 0 channel 1 

branch 0 branch 1 

Memory Controllers 

S26361-F3313-E521 S26361-F3313-E522 S26361-F3313-E523 S26361-F3313-E524 

Upgrade memory 1GB Upgrade memory 2GB Upgrade memory 4GB Upgrade memory 8GB 


with SDDC=chipkill support with SDDC=chipkill support with SDDC=chipkill support with SDDC=chipkill support 





3x 

S26361-F3230-E521 S26361-F3230-E522 S26361-F3230-E523 S26361-F3230-E524 

Upgrade memory 1GB Upgrade memory 2GB Upgrade memory 4GB Upgrade memory 8GB 


with SDDC=chipkill support with SDDC=chipkill support with SDDC=chipkill support with SDDC=chipkill support 





E 



E 

Section IV Riser Card 

S26361-F3173-E102 S26361-F3173-E103 PCI-X Riser only 

PCIe Riser Card PCI-X Riser Card 2nd PCI-X slot is short 

1x PCI x8 standard long 1x PCI-X 64Bit/133MHz standard short 

standard or Low Profile cards useable standard or Low Profile cards useable 

Section V Graphics 

Graphics Controller is included in integrated remote 

Management Controlle iRMC. 

( 1280 x 1024 at 8bpp, 1024 x 768 at 16bpp, Resolution 85Hz ) 

S26361-F2748-E531 

PY VGA card 128MB PCI-e x1 

NVIDIA 

NVS285 

128 MB PCIe-x1 The hight end optional NVIDIA NVS285 graphic card offers dual head operation 

2x DVI or 2x VGA or and fully 3D video support. 

1x DVI plus 1x VGA The cables for either two times DVI or VGA connections are part of the delievery. 

cables adapters included Remote Video direction via iRMC must be disabled. 

Dual head + fully 3-D This PCIe-x1 card can also be installed in any PCIe-x4, x8 or x16 slot. 

supported for Windows OS Only one card per server is allowed. 

not supported for Linux OS (native) 

full height bracket 


F 





Following memory configurations are possible 

1.) Normal Mode 

B a n k 2 

FB - DIMM 

F B -DIMM 

F B -DIMM 

FB - D I M M 

Bank 2 

B a n k 1 

FB - DIMM 

F B -DIMM 

F B -DIMM 

FB - D I M M 

Bank 1 

Channel 

A 

Channel B Channel 

C 

Channel 

D 

Branch 0 

Memory Controller 

(Blackford 

MCH) 

Branch 1 

‣ Basically up to four different types of DIMMs pairs can be installed in Normal Mode. 

‣ The DIMMs of one pair must cover the same bank position on both channels of a branch. 

‣ DIMM pairs must be identical with respect to size, speed, and or ganization. 

‣ Within a branch memory DIMM pairs must be populated in bank order; Bank 1 first, Bank 2 second. 

‣ The two channels on each branch operate in lock step to increase FBD bandwidth. 

2.) Mirror Mode 

Example: FBD 1A = Fully Buffered DIM Module in Bank1 / Channel A 

F B- DIMM 

FBD 2D 

Memory 

Population 

F B- DIMM 

FBD 1D 

F B -DIMM 

FBD 2C 

P h y s i c a l 

V i e w 

Logical 

View 

F B -DIMM 

FBD 1C 

Mirroring 

F B -DIMM 

FBD 2B 

Bank 2 

F B - DIMM F B -DIMM 

( Spare ) 

F B - DIMM F B -DIMM 

( Spare ) 

F B - DIMM ( M) 

Spare ) 

F B - DIMM ( M Spare ) 

) 

Bank 2 

F B -DIMM 

FBD 1B 

F B -DIMM 

FBD 2A 

Bank 1 

F B - DIMM 

F B - DIMM 

F B - DIMM (M) 

F B - DIMM (M) 

Bank 1 

F B -DIMM 

FBD 1A 

Mirroring 

ChA 

Memory 

C h B C h C 

Controller 

( B l a c k f o r d 

MCH) 

Branch 0 

ChD 

Branch 1 

C h a n n e l 

A 

0 

C h a n n e l B 1 

C h a n n e l 

C 

2 

C h a n n e l 

D 

3 

B r a n c h 0 

B r a n c h 1 

Memory Controller 

(Blackford 

MCH) 

‣ Basically up to two different types of DIMM pairs can be installed in Mirror Mode (one type in bank 1, one type in bank 2) 

‣ Mirroring requires both branches, since both branches contain identical images of memory data. 

‣ Both DIMM pairs in brach0 and branch1 of one bank must be identical with respect to size, speed, and organization. 

‣ Mirroring & branch interleaving are mutually exclusive of each other. 

‣ Within a bank memory DIMM pairs must be populated in branch order; Branch 0 first, mirrored DIMM pairs in Branch 1 

s e c o n d . 

Fujitsu Siemens Computers Enterprise Products PRIMERGY Server 12 of 22


F PRIMERGY RX200 S3 Status 2008-04-28 

Section VI Accessible drives 

Setup RX200 S3 by ServerStart is supported with following configurations: 

no Floppy, no DVD, no CD: 

remote installation only ( PXE service & DHCP server required) 

built in CD/DVD or USB CD/DVD, no Floppy disk drive: 

UNC Network share reachable or USB Floppy connected 

USB Floppy, no CD/DVD: 

USB CD/DVD connected 

If installation is done locally, make sure you have internal 

or external FDD available for driver installation. 

Following USB Components are available 

1 ) U S B D V D + - R W : S26391-F7119-L100 

Super Multi DVD slim drive (USB cable included) 

2) FDD USB (external): S26391-F264-L226 

external USB FDD (USB cable included) 

3) USB Keyboard: S26381-K340-V120 

KBPC PX D, professional keyboard 

4) USB Mouse: S26381-K415-L100 

Optical Wheel Mouse Tilt USB/PS2 

5) USB Memorybird: 

Memorybird 2GB S26391-F6047-L102 

Memorybird 4GB S26391-F6047-L104 

S26361-F3123-E1 

S26361-F3236-E1 

CD-RW / DVD drive 0.5" DVD-RW 8x super multi drive 

1x 24/24/24x / 8x ATAPI all formats, DUAL/DL, DVD-RAM 

CD-RW only with W2K, W3K, Linux only W2K, W3K and Linux 

0.5 x 5.25", anthracite bezel 0.5 x 5.25", anthracite bezel 

max. 1x per system max. 1x per system 

G 




G PRIMERGY RX200 S3 Status 2008-04-28 

Section VII Hard disks drives 

There is one HDDs bay. 

It can be configured either with a 4x 2.5" HDD or 2x 3.5" HDD option 

4x 2.5" HDD option 2x 3.5" HDD option 

S26361-F3317-E100 

S26361-F3317-E200 

Drive Bay with up to 4x 2.5" slots Drive Bay with up to 2x 3.5" slots 

H 

There is a 8 port SAS controller on-board. 

Up to 4 SAS/SATA 2.5" hard disks or 2x SAS/SATA 3.5" hard disks can be configured. 

Mix of SAS and SATA hard disks is not allowed within one system 

SATA HDDs are supported only with IME 

S26361-F3209-E60 

HD 60GB 7.2krpm 2.5" 

4x 7.200rpm,


H PRIMERGY RX200 S3 Status 2008-04-28 

S26361-F3218-E80 S26361-F3218-E160 S26361-F3218-E250 S26361-F3218-E500 

HD 80GB 7.2krpm 3.5" HD 160GB 7.2krpm 3.5" HD 250GB 7.2krpm 3.5" HD 500GB 7.2krpm 3.5" 

2x 7200rpm,

S y s t e m c o n f i g u r a t o r a n d o r d e r - i n f o r m a t i o n g u i d e 


I 

J 

Standard/Low Profile PCI slot 

only 1x per System 

Low Profile PCI slot 


Section VIII SCSI-Controller SCSI- Controller Low Profile 

On-board SAS-Controller for SAS-HDs with RAID1/1E On-board SAS-Controller for SAS-HDs with RAID1/1E 

The system is equipped with a eight channel SAS on-board controller and embedded "IME". 

IME (Integrated Mirroring Enhanced) offers the RAID levels 0, 1, 1E without any additional costs. 

IME is a RAID 0, 1 implementation, whereby RAID 1 can operate with an odd number of hard disks. 

Up to 4 hard disks including one hot spare HD are possible (limited by HHD slots in system). 

Administration of IME is possible with the LSI Global Array Manager (GAM). 

Windows2000/2003 as well as SUSE and RedHat Linux are supported (Restrictions refer to Software Configurator) 

The SAS IME solution supports 2 independent RAID volumes. Both volumes have to contain either SAS or SATA HDDs only. 

No additional components required. 

1x per server 

PCI - X 

SCSI-controller for 

external drives and peripheral devices 

PCIe 

SCSI- controller for 

external drives and peripheral devices 

S26361-F2737-E201 Only released for S26361-F2737-E201 

SCSI 160 Controller, LP SX10. All contr. SCSI 160 Controller, LP 

Adaptec for the connection Adaptec 

SCSI Card 29160, Low Profile of external storage SCSI Card 29160, Low Profile 

1 channel U160 LVD systems are 1 channel U160 LVD 

only external connection delivered without only external connection 

64/66(32/33) PCI, Low Profile cables. For the 64/66(32/33) PCI, Low Profile 

ext: VHDCI, 68 pol., U160 configuration of ext: VHDCI, 68 pol., U160 

S W : external cabling S W : 

max. 2x per system see configurator max. 2x per system 

of external storage 

s y s t e m s . 

J 

K 

F u j i t s u S i e m e n s C o m p u t e r s 

Enterprise Products PRIMERGY Server 1 6 o f 2 2



K 

L 

Standard or Low Profile PCI slot 




Section IX Fibre-Channel Controller Fibre-Channel Controller Low Profile 

No mix and match for Qlogic and Emulex Fibre Channel Controllers possible. 

With Qlogic Controller 

O 

With Emulex Controller 

PCIe Cards 

M 

PCI-X Cards 

PCI-X 

S26361-F3122-E201 

S26361-F3122-E201 

2GBit/s FC Controller 2GBit/s FC Controller 

Emulex 

Emulex 

LP101, Low Profile bracket LP101, Low Profile bracket 

1 channel 2GBit/sec FC Controller 1 channel 2GBit/sec FC Controller 

LC Interface for 50µm Fiber LC Interface for 50µm Fiber 

PCI-X 64Bit / 133MHz, 170mm PCI-X 64Bit / 133MHz, 170mm 

3.3V / 5V tolerant signaling 3.3V / 5V tolerant signaling 

max. 2 per system max. 2 per system 

L 

M 

M 

N 

PCIe Cards 

S26361-F3306-E201 

4GBit/s FC Controller 

Emulex 

LPe1150, Low Profile bracket 

1 channel 4GBit/sec FC Controller 

LC Interface for 50µm Fiber 

PCIe x4, 170mm 


S26361-F3306-E202 

4GBit/s FC Controller 

Emulex 

LPe11002, Low Profile bracket 

2 channel 4GBit/sec FC Controller 

LC Interface for 50µm Fiber 

PCIe x4, 170mm 


All controllers for the connection of external storage systems are delivered without cables. 

For the configuration of external cabling see the configurator for external storage systems. 

For Fibre Channel SAN also other componets like switches, SFPs and optical wires are 

orderable (for details see price liste) 

N 

Q 





O 

P 

With Qlogic Controller 

PCIe 

PCI-X 

PCI-X 

S26361-F3097-E201 

S26361-F3097-E201 


Qlogic 

Qlogic 

QLA2340, Low Profile bracket QLA2340, Low Profile bracket 



PCI-X 64Bit / 133MHz, 170mm PCI-X 64Bit / 133MHz, 170mm 

3.3V / 5V tolerant signaling 3.3V / 5V tolerant signaling 


total 

2x 

S26361-F3483-E201 

S26361-F3483-E202 


Qlogic 

Qlogic 

QLE2460, low profile bracket QLE2462, low profile bracket 



PCIe x4, 170mm PCIe x4, 170mm 

max. 1 per system max. 1 per system 

All controllers for the connection of external storage systems are delivered without cables. 

For the configuration of external cabling see the configurator for external storage systems. 

For Fibre Channel SAN also other componets like switches, SFPs and optical wires are 

orderable (for details see price liste) 

P 

Q 





Q 

R 

Standard or Low Profile PCI slot 


Low profile PCI slot 


Sections X Disk Array 

8-channel SAS on-board controller with LSI Integrated Mirroring (IME) 

SAS-cabling of a PRIMERGY RX200 S3 basic unit with on-board controller 

SAS controller is connected to the internal hard disks only. 

1x per PRIMERGY RX200 S3 

SAS RAID-Controller for internal Disk Arrays 

S26361-F3216-E2 

S26361-F3085-E202 

8 port SAS RAID Controller With zero channel RAID controller 0-channel SAS RAID controller 

LSI the IME function is no longer LSI 

MegaRAID SAS/SATA 8308 available. MegaRAID SAS 8300XLP 

128MB SDRAM ECC Cache 128MB Cache with ECC 

RAID 0, 1, 10, 5 & 50 RAID 0, 1, 10, 5 & 50 

optional 

BBU 

SAS 3Gb/sec Controller plus special SAS cable in combination with on-board 

8 SAS port internal required for RX200 S3 SAS initiator 

PCIe x4, 198mm 64Bit/66MHz PCI-X controller 

LP height, 198mm length 3.3V power supply & signaling 


S26361-F3216-E11 iBBU with special cable for RX200 S3. 

Cache Battery Backup Unit The iBBU is mounted in the cabinet, not 

max. 1x per controller on the controller. 

PCI-X 

RAID-Controller for external Disk Arrays 

S26361-F3006-E128 

2-channel RAID Controller U320 

LSI 

320-2 Attention 

128MB SDRAM ECC Cache 2-channel RAID 

RAID 0, 1, 10, 5 & 50 Controllers only 

default with TBBU usable for 

plug: internal 2x HD68; external HDDs (SX30) 

external: 2x VHDCI 

without 

cable 

64/66 PCI controller, 180mm 

3.3V and 5V tolerant signaling 


R 

S 





S 

T 

Section XI Communication / Network Communication / Network Low Profile 

D u a l G i g a b i t E t h e r n e t C o n t r . o n b o a r d Teaming: Failover, Load Balancing 

Broadcom BDC5715 T h e I n t e l L A N C o n t r o l l e r s 1 0 0 0 T X . 1 0 0 0 M F , 1 0 0 0 M T 

ext: 2x RJ 45 connector c a n b e u s e d w i t h t h e o n - b o a r d c o n t r o l l e r i n T e a m i n g M o d e . 

Standard/Low Profile PCI slot 


PCI-X 

PCIe 



S26361-F3142-E202 r e s p i n S26361-F3142-E202 r e s p i n 

( S t e b b i n s 2 L F r e s p i n ) ( S t e b b i n s 2 L F r e s p i n ) 

G i g a b i t E t h e r n e t C o n t r o l l e r 1 0 0 0 T X L P G i g a b i t E t h e r n e t C o n t r o l l e r 1 0 0 0 T X L P 

E t h C t r l 1 x 1 G b i t E t h C t r l 1 x 1 G b i t 

P C I 3 2 P R O / 1 0 0 0 G T C u L P P C I 3 2 P R O / 1 0 0 0 G T C u L P 

I n t e l P r o / 1 0 0 0 G T D e s k t o p A d a p t e r I n t e l P r o / 1 0 0 0 G T D e s k t o p A d a p t e r 

P C I 3 2 ( 3 3 / 6 6 M H z ) , L o w P r o f i l e P C I 3 2 ( 3 3 / 6 6 M H z ) , L o w P r o f i l e 

e x t : f o r R J 4 5 - c o n n e c t o r , C a t 5 e x t : f o r R J 4 5 - c o n n e c t o r , C a t 5 


S26361-F3054-E201 

S26361-F3054-E201 

G i g a b i t E t h e r n e t C o n t r . 1 0 0 0 S X L P G i g a b i t E t h e r n e t C o n t r . 1 0 0 0 S X L P 

E t h . C t r l 1 x 1 G b i t P C I - X P r o / 1 0 0 0 M F L C L P E t h . C t r l 1 x 1 G b i t P C I - X P r o / 1 0 0 0 M F L C L P 

I n t e l P R O / 1 0 0 0 M F S e r v e r A d a p t e r I n t e l P R O / 1 0 0 0 M F S e r v e r A d a p t e r 

PCI-X (PCI64/133), min 165 mm PCI-X (PCI64/133), min 165 mm 

ext:LC-connector 

ext:LC-connector 


S26361-F3053-E201 

S26361-F3053-E201 

G i g a b i t E t h e r n e t C o n t r o l l e r 1 0 0 0 T X L P G i g a b i t E t h e r n e t C o n t r o l l e r 1 0 0 0 T X L P 

E t h C t r l 1 x 1 G b i t P C I - X P r o / 1 0 0 0 M T C u L P E t h C t r l 1 x 1 G b i t P C I - X P r o / 1 0 0 0 M T C u L P 

I n t e l P R O / 1 0 0 0 M T S e r v e r A d a p t e r I n t e l P R O / 1 0 0 0 M T S e r v e r A d a p t e r 

max. 2x P C I - X ( P C I 6 4 / 1 3 3 ) , L o w P r o f i l e P C I - X ( P C I 6 4 / 1 3 3 ) , L o w P r o f i l e 

G i g a b i t e x t : f o r R J 4 5 - c o n n e c t o r , C a t 5 e x t : f o r R J 4 5 - c o n n e c t o r , C a t 5 

E t h e r n e t c a r d s max. 2x per system max. 2x per system 

S26361-F3227-E202 r e s p i n S26361-F3227-E202 r e s p i n 

( D o u b l e B a r r o w I I L F r e s p i n ) ( D o u b l e B a r r o w I I L F r e s p i n ) 

G i g a b i t E t h e r n e t C o n t r . D u a l 1 0 0 0 T X L P G i g a b i t E t h e r n e t C o n t r . D u a l 1 0 0 0 T X L P 

E t h C t r l 2 x 1 G b i t E t h C t r l 2 x 1 G b i t 

PCI-X PRO/1000GT Cu LP PCI-X PRO/1000GT Cu LP 

I n t e l P r o / 1 0 0 0 G T D u a l P o r t S e r v e r A d . I n t e l P r o / 1 0 0 0 G T D u a l P o r t S e r v e r A d . 

P C I - X ( P C I 6 4 / 1 3 3 ) , L o w P r o f i l e P C I - X ( P C I 6 4 / 1 3 3 ) , L o w P r o f i l e 

e x t : f o r R J 4 5 - p l u g , C a t 5 e x t : f o r R J 4 5 - p l u g , C a t 5 


S26361-F3228-E201 S26361-F3241-E201 S26361-F3242-E201 

G i g a b i t E t h e r n e t C o n t r o l l e r D u a l 1 0 0 0 T X G i g a b i t E t h e r n e t C o n t r . 1 0 0 0 T X L P G i g a b i t E t h e r n e t C o n t r . 1 0 0 0 S X L P 

Eth. Ctrl 2x1Gbit PCIe PRO/1000PT Cu E t h C t r l 1 x 1 G b i t P C I - e P r o / 1 0 0 0 P T C u L P E t h C t r l 1 x 1 G b i t P C I - e P r o / 1 0 0 0 P F L C L P 

I n t e l P r o / 1 0 0 0 P d u a l S e r v e r A d a p t e r I n t e l P R O / 1 0 0 0 P T S e r v e r A d a p t o r I n t e l P R O / 1 0 0 0 P F S e r v e r A d a p t e r 

PCIe x4 PCIe x1 PCIe x4 

e x t : f o r R J 4 5 - p l u g , C a t 5 e x t : f o r R J 4 5 - c o n n e c t o r , C a t 5 ext:LC-connector 

max. 1x per system max. 1x per system max. 1x per system 

T 

U 




U PRIMERGY RX200 S3 Status 2008-04-28 

Section XII System Management Products (RemoteView) 

S26361-F1790-E240 

iRMC advanced pack 

integrated remote management controller 

activation key for 

graphical console redirection 

and remote media redirection 


S26361-F1790-E221 

RemoteView Software V5.0 

Installation and configuration of 

RemoteView Web and LAN FrontEnd 

BMC-Manager, RTDS and FreeDOS 

Online 

manuals 

Section XIII Miscellaneous 

USB Input devices available: 

1) USB Keyboard: S26381-K340-V120 

KBPC PX D, professional keyboard 

2) USB Mouse: S26381-K403-L100 

Optical Wheel Mouse 

Options and other peripherals 

For other options, refer to SystemArchitect and Pricelist. 

These options are supplied lose with the shipment. 

For suitable peripherals for this product, please refer to SystemArcitect. 

Section XIV Country specific power cord 

Country specific power cords are not required for rack versions, except for USA&Canada. 

Power cords are shipped in a rack version with inlet connector for non-heating apparatus. 

Description in englisch. Both included in basic unit. 

(1x with Standard PSU, 2x with hot plug upgrade) 

T26139-Y1742-E10 USA, Canada 

For shipments to USA&Canada, you have to order 

one power cord (1,8m, grey) per power supply. 

End PRIMERGY RX200 S3 





Change Report 

Date Order number Changes 

2007-11-03 S26361-F3215-E10 Cache Battery Backup Unit - no longer available 

2007-11-03 S26361-F3215-E1 8 port SAS RAID Controller - no longer available 

2007-10-26 S26361-K995-V241 PY RX200S3 with Xeon DP 5140 (2.33GHz/4M/1333) - no longer available 

2007-10-26 S26361-K995-V221 PY RX200S3 with Xeon DP 5120 (1.86GHz/4M/1066) - no longer available 

2007-10-26 S26361-K995-V131 PY RX200S3 with Xeon DP 5050 (3.00GHz/2x2M/1066) - no longer available 



2007-09-12 S26361-F3215-E10 changed S26361-F3215-E210 to S26361-F3215-E10 

2007-09-12 S26361-F3215-E1 changed S26361-F3215-E201 to S26361-F3215-E1 

2007-08-30 S26361-F3483-E202 2 channel 4GBit/sec FC Controller LP - now available 

2007-08-30 S26361-F3483-E201 1 channel 4GBit/sec FC Controller LP - now available 

2007-07-25 S26361-F3011-E201 Gigabit Ethernet Controller Dual 1000TX LP- no longer available 

2007-07-25 S26361-F3241-E201 Gigabit Ethernet Contr. 1000TX LP- no longer available 

2007-07-12 S26361-F3216-E2 Cache Battery Backup Unit - now available 

2007-07-12 S26361-F3216-E11 8 port SAS RAID Controller - now available 

2007-07-10 S26361-F3349-E460 Processor 64-bit Intel Xeon LV DP L5310 - now available 

2007-07-10 S26361-K995-V511 PY RX200S3 with Xeon LV DP L5310 (1.60GHz/2x4M/1333) - now available 



2007-07-10 S26361-F3349-E300 Processor 64-bit Intel Xeon DP X5365 - now available 

2007-07-10 S26361-K995-V507 PY RX200S3 with Xeon DP X5365 (3.00GHz/2x4M/1333) - now available 

2007-07-03 S26361-F3215-E10 Cache Battery Backup Unit - now available 

2007-07-03 S26361-F3215-E201 8 port SAS RAID Controller - now available 


2007-06-14 S26361-F3085-E10 Cache Battery Backup Unit for 0-channel SAS RAID controller - no longer available 

2007-04-27 S26361-F3208-E573 HD 73GB 15krpm 2.5" - now available 

2007-04-27 S26361-F3208-E536 HD 36GB 15krpm 2.5" - now available 

2007-04-26 S26361-F3227-E202 Gigabit Ethernet Controller Dual 1000TX LP - now available 

2007-04-26 S26361-F3142-E202 Gigabit Ethernet Controller 1000TX LP - now available 

2007-02-14 Virtual Infrastructure 3 - now available 



2007-02-12 S26361-K995-V244 PY RX200S3 with Xeon LV DP E5148 (2.33GHz/4M/1333) - now available 

2007-02-12 S26361-F3322-E433 Processor 64-bit Intel Xeon LV DP E5148 - now available 

2007-01-18 S26361-F2748-E531 NVIDIA NVS285 graphic card - as soon as available 


2007-01-15 S26361-K995-V504 PY RX200S3 with Xeon DP E5335 (2.00GHz/2x4M/1333) - now available 

2006-12-07 S26361-F3349-E233 Processor 64-bit Intel Xeon DP E5345 - now available 



2006-12-07 S26361-K995-V506 PY RX200S3 with Xeon DP X5355 (2.66GHz/2x4M/1333) - now available 

2006-11-22 S26361-F3241-E1 Gigabit Ethernet Contr. 1000TX - now available 

2006-11-22 S26361-F3241-E2 Gigabit Ethernet Contr. 1000SX - now available 

2006-10-24 S26361-F3204-E130 HD SAS 300GB 10krpm 3.5" - now available 








2006-06-26 S26361-F3230-E52* Upgrade memory 1 … 8GB FBD667 / PC2-5300F - as soon as available 

2006-06-26 S26361-F3230-B52* Base Memory 1 … 8GB FBD667 / PC2-5300F - as soon as available 

2006-06-02 S26361-F1790-E221 RemoteView Software V5.0 - now available 

2006-05-04 First release

PRIMERGY RX200 S3

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?