PRIMERGY TX600 S3

PRIMERGY TX600 S3 

System configurator and order-information guide 

May 2006 

Contents 

Instructions 

Configuration 

diagram 

Configurator 

0 System software 

I Basic unit 

I I Processor 

I I I Memory 

I V Hard disk drives / Tapes 

V SCSI / RAID controller 

VI Fibre Channel controller 

VII Communication / Network 

V I I I System Management Products (RemoteView) 

I X Miscellaneous 

X Power cords 

Change 

report 

PRIMERGY Server


PRIMERGY TX600 S3 Status 24.04.2006 

Instructions 

This document contains basic product and configuration information that will enable you to configure your system via 

P C - / S y s t e m - A r c h i t e c t . 

Only these tools will ensure a fast and proper configuration of your PRIMERGY server or your complete 

P R I M E R G Y R a c k s y s t e m . 

You can configure your individual PRIMERGY server in order to adjust your specific requirements. 

The System configurator is divided into several chapters that are identical to the current price list and PC-/ System-Architect 

Please follow the lines. If there is a junction, you can choose which way or component you would like to take. Go through 

the configurator by following the lines from the top to the bottom. 

Section III Memory, example 

There are X memory slots which can be equipped with XXX MB. 

It is permissible to make up to X passes through the memory upgrade options. 

X 

times 

S26361-XXX-XXX 

S26361-XXX-XXX 

Memory XXX MB Memory XXX MB 

max. X times per system max. X times per system 

In one chapter you can only select as many components (here 4x) as the arrow indicates. 4x 

Please note that there are information symbols which indicate necessary information. 

Further information in the internet see: 

http://www.primergy.com 

http://extranet.fujitsu-siemens.com/primergy 

(internet) 

(extranet) 

Prices and availability see price list and PC-/ System-Architect 

Subject to change and errors excepted 

Fujitsu Siemens Computers 

Enterprise Products - PRIMERGY Server 2 of 16



TOP View 

Configuration diagram PRIMERGY TX600 S3 

System unit ( I ) 

Slot 

Extension slots Memory ( III ) 

SCSI / RAID controller ( V ) 

Fiber Channel ( VI ) 

Memory Board A 

Communication/Network ( VII ) 

(2 Banks / 4 modules) 

7 

6 

5 

PCI-X 64-Bit / 100MHz, long 

PCI-X 64-Bit / 100MHz, long 

PCI-Express x4 ( hot-plug ) 

Memory Board B 


Memory Board C 


Memory Board D 


4 

3 

2 

1 



PCI-X 64-Bit / 133MHz, long ( hot-plug ) 


Processors must be plugged 

in order according the picture. 

Processor ( II ) 

Xeon 

MP 3 

Xeon 

MP 4 

Xeon 

MP 2 

Xeon 

MP 1 

Operating Panel 

FRONT VIEW 

Operating 

Panel 

Video 

Accessible drives 

5.25"x 0.5" bay for CD/DVD 

Local View LCD Display 

Tape drives ( IV ) 

USB 

USB 

USB 

Hard disk drives ( IV ) hot-plug 

Channel A Channel B 

3.5"x1" SCSI-ID 4 3.5"x1" SCSI-ID 4 

3.5"x1" SCSI-ID 3 

3.5"x1" SCSI-ID 3 

3.5"x1" SCSI-ID 2 3.5"x1" SCSI-ID 2 

5.25"x1.6" Tape Drive 3.5"x1" SCSI-ID 1 3.5"x1" SCSI-ID 1 

5.25"x1.6" Tape Drive 3.5"x1" SCSI-ID 0 3.5"x1" SCSI-ID 0 

COM 

Video 

USB 

USB 

Ether 

net 

Ether 

net 

REAR VIEW 

Hot Plug Redundant Power Supply 

1 . P S U 2 . P S U 

Key: 

Included in basic unit 

Option 




Start "PRIMERGY TX600 S3" PRIMERGY TX600 S3 Status 24.04.2006 

SW Configurator 32 bit 

with OEM-Software 

without OEM-Software 

for PRIMERGY Server Usage of OEM SW from MS is for PRIMERGY Server 

not possible under ESX or GSX 

Later use of OEM operating system 

VMware-Software as soon as available software is not allowed, 

- VCMS VirtualCenter Management Server apart from few VMware 

- ESX Server and ESX Virtual Infrastructure Node add-ons 

- P2V Assistant Enterprise Edition 

For all SW products please refer to the corresponding software configurator accessible via 

the Extranet under Configuration & Tools, -All configurations, -Software, URL see below. 

MS - Software: W **) PRIMECLUSTER *) 

- Windows 2000 Server - Clustering 

- Windows 2000 Advanced Server - Load Balancing 

- Windows Server 2003, 

Standard 

Edition 

Enterprise Edition Linux - Software: L **) 

- Additional loose - SuSE Linux Enterprise Server 

Client-Access-Licenses (CALs) - Red Hat Enterprise Linux 

(not for Web Edition) 

CITRIX-Software for 

Windows: W-MF 

- Presentation Server 

LoadBalancing 

Additional User Licences 

MultiPath, Duplex Data Manager (DDM) 

W2K; W2K3 Linux (W-DDM) 

Adaptive Services Control Center (ASCC) 

Details eg. version numbers are published 

ASCC Satellite Node in the separate SW-Configurator 

SLES 

Manageability Software: V 

- RemoteView Software 

- RemoteView Service Board 

Backup-Software / 

Application-Software: U 

- ARCserve 

- openSM2 

*) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under 

http://extranet.fujitsu-siemens.com/primecluster 

**) Pay attention to the release and ordering information in PRINCE -> Operating System 

http://vil.mch.fsc.net/vil/pc/vil/primergy/overview/prince/index_en.htm 

Find detailed software configurators and release lists (OS-matrix / system management) under following addresses: 

for internal users: 

for partners: 

http://vil.mch.fsc.net/vil/oec/special/primergy/index_en.htm 

http://vilpart.fujitsu-siemens.de/vil/oec/special/primergy/index_en.htm 

Continue with PRIMERGY 

HW configurator 




Start "PRIMERGY TX600 S3" PRIMERGY TX600 S3 Status 24.04.2006 

SW Configurator EM64T 

with OEM-Software 

without OEM-Software 

for PRIMERGY Server for PRIMERGY Server 

Later use of OEM operating 

For all SW products please refer to the corresponding system software is not allowed! 

software configurator accessible via the Extranet under 

"Configuration & Tools, -All configurations, -Software, 

URL see below. 

as soon as available 

Microsoft - Software: W Linux - Software: L *) **) 

only - Windows Server 2003, only - SuSE Linux Enterprise Server 

EM64T x64 Standard Edition EM64T - Red Hat Enterprise Linux 

x64 Enterprise Edition 

- Additional loose 

Client-Access-Lizenzen 

(CALs) 

CITRIX-Software for 

only Windows: W-MF 

EM64T - Presentation Server 

LoadBalancing 

Additional User Licences 

only MultiPath, Duplex Data Manager (DDM) 

EM64T Windows, Linux (W-DDM) 

Details eg. version numbers are published 

Manageability Software: V**) 

in the separate SW-Configurator 

only - RemoteView Software 

EM64T - RemoteView Service Board 

- RemoteView Diagnosis *) Pay attention to the PRIMECLUSTER release and ordering information in the Extranet under 

http://extranet.fujitsu-siemens.com/primecluster 

**) Pay attention to the release and ordering information in PRINCE -> Operating System 

http://vil.mch.fsc.net/vil/pc/vil/primergy/overview/prince/index_en.htm 

You'll find single software configurators and release lists (OS-matrix / system management / security) under following addresses: 

for internal users: 

for partners: 

http://vil.mch.fsc.net/vil/oec/special/primergy/index_en.htm 

http://vilpart.fujitsu-siemens.de/vil/oec/special/primergy/index_en.htm 

Continue with PRIMERGY 

HW configurator 




Start PRIMERGY TX600 S3 PRIMERGY TX600 S3 Status 24.04.2006 

Section I Basic unit 

PRIMERGY TX600 S3 PRIMERGY TX600 S3 Basic Unit including: 

- 2 hot-plug power supply (redundant) 

Floorstand-version Rack-version - 6 hot-plug fans (redundant) 

Basic unit with: Basic unit with: - 5 + 5 bays for 1" HDD`s (two channels) 

- 1x XEON MP processor (max. 4) - 1x XEON MP processor (max. 4) - 1 bay (0,5" height) for CD- or DVD-ROM 

with 667/800MHz Frontside Bus with 667/800MHz Frontside Bus - 2x 5.25" bays FH (1.6" high) for accessible drives 

- USB Mouse with two push buttons - Rack Mounting Kit 

- Floorstand kit with lockable front door - LCD-Display for LocalView Systemboard with 

- 2x power cord with 16A Schuko - 2x power cord with 10A IEC320 C14 - Intel E8501 chipset 

(S26361-F3151-E100) (S26361-F3151-E350) - One 64bit Xeon MP CPU (2nd, 3rd and 4th as option) 

- memory of basic units selectable via - memory of basic units selectable via - 7 PCI Slots 

base memory order codes base memory order codes - 1x 64bit / 133MHz PCI-X slot (hot plug) 

3.16GHz / 1MB SLC S26361-K989-V112 3.16GHz / 1MB SLC S26361-K989-V512 - 2x 64bit / 100MHz PCI-X slot 

3.66GHz / 1MB SLC S26361-K989-V122 3.66GHz / 1MB SLC S26361-K989-V522 - 3x PCIe x4 slot (hot plug) 

2.67GHz/2MB 7020 S26361-K989-V312 2.67GHz/2MB 7020 S26361-K989-V712 - 1x PCIe x8 slot (hot plug) 

2.80GHz/2MB 7030 S26361-K989-V322 2.80GHz/2MB 7030 S26361-K989-V722 

3.00GHz/4MB 7041 S26361-K989-V332 3.00GHz/4MB 7041 S26361-K989-V732 - 1 memory board (2nd, 3rd and 4th as option) 

- Ultra 320 SCSI-controller (LSI 53C1030) 

- onboard RAID 5 functionality with 256MB Cache 

(RAID BBU optional) 

- Dual LAN-Controller 1GBit on-board 

WOL-capable (BroadCom 5704) 

- VGA Controller on-board 

(ATI Radeon 7000M, 16MB RAM) 

Power cables must be order seperatly, - Server Management Controller on-board 

see section "X Power Cords" (RSB 2 Board optional) 

- ServerStart packet incl. ServerBooks CD, 

ServerSupport CD and ServerView 

External Interfaces: 

Front 

side 

PRIMERGY PRIMECENTER- Rack "Rack-mounting ex factory" 3x USB 2.0 

This service is to be ordered once 1x VGA (15 pin) 

per installable server/storage 

SNP:SY-F1647E301-P subsystem, in order to get the Rear Side 

Installation ex works for one server/storage subsystem 2x USB 2.0 

server or subsystem. mounted into the PRIMERGY racks. 1x VGA (15 pin) 

Hereby the rack will be delivered In case of the 46 U PRIMERGY rack, 1x RS-232-C (serial, 9 pin) 

completely pre-mounted and this service has to be ordered, 2x RJ45 (on board LAN) 

all wired connections are tested. to get the mounting kits and the no PS/2 connection for KB / Mouse 

With racks 12U, 24U, 38U: cables installed (USB connectivity must be used instead) 

Systems and components 

will be delivered installed in the rack 

With racks 46U: Rack Mounting kit is part of the basic unit PRIMERGY TX600 S2 Rack 

Systems and components - 1 pair of telescopic rails (713 - 812mm) 

will be delivered separately - 1 bracket DC-PC-Rack 

To be ordered only together with - 1 cable management for DC-PC-racks 

a PRIMERGY- This kit allows for mounting of TX/RX600 S2 in in FSC 19" DataCenter- and 

PRIMECENTER rack PRIMECENTER- racks and all server racks conforming to EIA standard EIA-310-D for 19" racks. 

e . g . : Therefore the mounting kit is variable in depth from 713 - 812mm 

S26361-K826-V10x Installation in PRIMERGY 19" Classic rack is not possible. 

refer configurator DC-Rack Due to the heat dissipation of the system, sufficent cooling couldn´t be enabled in classic rack. 

max. 1x per System 

Connetion for KVM switch / Rack console 

- RC23 can be directly connected (both USB and PS/2 connections) 

- KVM S2 series needs the KVM S2 Adapter USBVGA 

- For ES4/8+ KVM series with PS/2 connector as well as for standard PS/2 KB / Mouse 

an additional USB to PS/2 adapter must be bought additionally and connected to the TX600 S2. 

The adapter offers 2x PS/2 ports. 

Adaper order number, to purchase via PRIMEPOWER, is: 

D:GP70P-KA01 Adapter for PS/2USB 

- Appropriate FSC USB keyboard is S26381-K340-V1* 

This keyboard also needs USB cable T26139-Y3812-V1 

A 




A PRIMERGY TX600 S3 Status 24.04.2006 

Section II Processor 

A 4-way processor system requires a multi-processor operating system 

Later upgrading to a four-way-processor system is also possible 

VRM´s for 1st/2nd CPU are on the Motherboard, for the 3nd / 4th CPU addition VRM Modules are required. 

Extension CPUs must have identical cache size and clock rate 

S26361-F3124-E311 

S26361-F3124-E361 

XEON MP 3.16GHz XEON MP 3.66GHz 

with 1 MB SLC on Chip, with 1MB SLC on Chip, 

heat sink and "Easy retention" heat sink and "Easy retention" 

occupies socket for one CPU occupies socket for one CPU 

max. 3x per system max. 3x per system 

S26361-F3124-E262 S26361-F3124-E282 S26361-F3124-E304 

XEON MP 7020 2.67GHz XEON MP 7030 2.80GHz XEON MP 7041 3.00GHz 

667 MHz FSB 800 MHz FSB 800 MHz FSB 

with 2x 1MB SLC on Chip, with 2x 1MB SLC on Chip, with 2x 2MB SLC on Chip, 

heat sink and "Easy retention" heat sink and "Easy retention" heat sink and "Easy retention" 

occupies socket for one CPU occupies socket for one CPU occupies socket for one CPU 

max. 3x per system max. 3x per system max. 3x per system 

S26361-F3124-E200 

VRM modules for 3rd/4th CPU 

max. 1x per system 

S26361-F3124-E311 

S26361-F3124-E361 

XEON MP 3.16GHz XEON MP 3.66GHz 

with 1 MB SLC on Chip, with 1MB SLC on Chip, 

heat sink and "Easy retention" heat sink and "Easy retention" 

occupies socket for one CPU occupies socket for one CPU 

up to max. 3x per system max. 3x per system 

2x 

S26361-F3124-E262 S26361-F3124-E282 S26361-F3124-E304 

XEON MP 7020 2.67GHz XEON MP 7030 2.80GHz XEON MP 7041 3.00GHz 

667 MHz FSB 800 MHz FSB 800 MHz FSB 

with 2x 1MB SLC on Chip, with 2x 1MB SLC on Chip, with 2x 2MB SLC on Chip, 

heat sink and "Easy retention" heat sink and "Easy retention" heat sink and "Easy retention" 

occupies socket for one CPU occupies socket for one CPU occupies socket for one CPU 


B 




B PRIMERGY TX600 S3 Status 24.04.2006 

Section III Memory 

The system can be equipped with up 4 memory boards with 2 memory banks each. 

One Memory Board is allready supplied in the base unit. 

Each memory board can be equipped with up to 2x 8GB = 16GB memory. 

The maximal extension is 64GB with 4GB modules! 

No mix of modules within one memory bank is allowed. 

For each basic unit, one pair of memory modules has to be ordered with the ordercode of "Base Memory" 

(either 2GB = 2x1GB, 4GB = 2x2GB or 8GB = 2x4GB) 

Note**: The price of the smallest Base Memory is already included in the basic unit, 

The price of the other Base Memories is the Delta to the smallest Base Memory 

Additional memory extensions (Upgrade Memory) can still be configured for the standard market price. 

ECC with memory scrubbing function is standard for TX600 S3. 

Optional hot-spare memory functionality can be configured in the BIOS (redundant memory bank n + 1) 

RX600 S3 supports the memory protection through Memory Mirroring or Memory RAID. 

Memory Mirroring requires 2 or 4 Memory boards, Memory RAID requires 4 Memory boards. 

see Note** above 

S26361-F3072-B622 S26361-F3072-B623 S26361-F3072-B624 

Base memory 2 GB Base memory 4 GB Base memory 8 GB 

DDR RAM PC2-3200 ECC DDR RAM PC2-3200 ECC DDR RAM PC2-3200 ECC 

with chipkill support with chipkill support with chipkill support 

consisting of 2 modules consisting of 2 modules consisting of 2 modules 

with 1 GB each with 2 GB each with 4 GB each 

occupies one bank occupies one bank occupies one bank 

max. 1x per base system max. 1x per base system max. 1x per base system 

S26361-F3072-E622 S26361-F3072-E623 S26361-F3072-E624 

Upgrade memory 2 GB Upgrade memory 4 GB Upgrade memory 8 GB 






max. 1x per base system max. 1x per base system max. 1x per base system 

S26361-F3125-E130 

Memory Board with 2 banks 

for 2 modules each 


up 

to 

3x S26361-F3072-E622 S26361-F3072-E623 S26361-F3072-E624 

Upgrade memory 2 GB Upgrade memory 4 GB Upgrade memory 8 GB 






max. 2x per memory board max. 2x per memory board max. 2x per memory board 

C 




C PRIMERGY TX600 S3 Status 24.04.2006 

Section IV Hard disk drives / Tapes 

Alternatives for cabling of the onboard SCSI controller of PRIMERGY TX600 S3 

Picture 1: Picture 2: Picture 3: 

Two channels for Disks One ch. for Disks + int. Tape One ch. for Disks + ext. Tape 

1x5 1x5 1x5 

onboard HDD onboard HDD onboard HDD 

SCSI / RAID SCSI / RAID SCSI / RAID 

1x5 internal ext. 

HDD Tapes SCSI Devices 

Configuration with 2 channels for Disk Drives Picture 1 

Both channels of the on-board SCSI/RAID-controller are used for SCSI disk drives (pls see pictures above). 

For the connetion of internal tape devices an additonal SCSI controller is required, pls see section V SCSI-RAID controller 

Configuration with 2 channels for Disk Drives plus internal Tape device Picture 2 

One channel of the on-board SCSI/RAID-controller is used for SCSI disk drives (pls see pictures above). 

The secound channel can be used to connect additional SCSI drives drives and /or an internal tape device. 

Configuration with 1 channels for Disk Drives plus external Tape device Picture 3 

One channel of the on-board SCSI/RAID-controller is used for SCSI HDD (pls see pictures above). 

The secound channel can be used to connect external Tape drives. 

Additional options with 29160 SCSI Controller 

optional optional optional 

internal 

internal 

Tape Devices Tape Devices 

29160 Contr. 29160 Contr. 29160 Contr. ext. 

internal Tape Devices 

Tape 

Devices 

29160 Contr. 29160 Contr. ext. 29160 Contr. ext. 

Tape Devices Tape Devices 

One of the following USB devices must be used for integrating the drivers during installation 

process if no automized (e.g. Serverstart / Altiris / RIS / ADS / …) installation is done: 

1 ) U S B D V D + - R W : S26391-F3152-L300 

Traveller III DVD DL super multi drive (USB cable included) 

2) FDD USB (external): S26391-F264-L226 

external USB FDD (USB cable included) 

3) USB Keyboard: S26381-K340-V120 

KBPC PX D, professional keyboard 

4) USB Mouse: S26381-K403-L100 

Optical Wheel Mouse 

5) USB Memorybird: S26391-F6046-L24 

Memorybird 

1GB 

Additionally a monitor can be connected to the VGA 15-pin interface. 

D 




D PRIMERGY TX600 S3 Status 24.04.2006 

S26361-F3123-E1 

S26361-F3236-E1 

CD-RW / DVD drive 0.5" DVD-RW 8x super multi drive 

24/24/24x / 8x ATAPI all formats, DUAL/DL, DVD-RAM 

1x CD-RW only with W2K, W3K, Linux only W2K, W3K and Linux 

0.5 x 5.25", anthracite bezel 0.5 x 5.25", anthracite bezel 


S26361-F3128-E101 

internal SCSI-Cable For the 1st tape drive 

for connetion of 

internal Tape devices 


S26361-F3158-E3 

Tape drive LTO3 Ultrium 

400GB, 80MB/s, U160 SCSI 

Connector: 

HD68 

1x without cable 

incl. description (Ger/US) 

data and cleaning cartridge 

3.2 x 5.25", anthracite bezel 


S26361-F2848-E3 S26361-F2849-E3 S26361-F3224-E3 S26361-F3157-E3 

Tape drive DDS Gen5 Tape drive VXA-2 Tape drive VXA-320 Tape drive LTO2HH Ultrium 

S26361-F2848-E31 (only for OBDR) 80GB, 6MB/s, U2W SCSI 160GB, 12MB/s, U160 SCSI 200GB, 24MB/s, U160 SCSI 

DDS-G5 for One buttom dis. recov. Connector: HD68 Connector: HD68 Connector: HD68 

1x 36GB, 3MB/s, U2W SCSI without cable without cable without cable 

Connector: HD68 incl. description (Ger/US) incl. description (Ger/US) incl. description (Ger/US) 

Up to without cable data and cleaning cartridge data and cleaning cartridge data and cleaning cartridge 

2 tape incl. description (Ger/US) 1.6 * 5.25", anthracite bezel 1.6 * 5.25", anthracite bezel 1.6 * 5.25", anthracite bezel 

drives data and cleaning cartridge max. 1x per system max. 1x per system max. 1x per system 

1.6 * 5.25", anthracite bezel 


S26361-F3128-E101 

internal SCSI-Cable For the 2nd tape drive 

for connetion of 

internal Tape devices 


S26361-F2848-E3 S26361-F2849-E3 S26361-F3224-E3 S26361-F3157-E3 

Tape drive DDS Gen5 Tape drive VXA-2 Tape drive VXA-320 Tape drive LTO2HH Ultrium 

S26361-F2848-E31 (only for OBDR) 80GB, 6MB/s, U2W SCSI 160GB, 12MB/s, U160 SCSI 200GB, 24MB/s, U160 SCSI 

DDS-G5 for One buttom dis. recov. Connector: HD68 Connector: HD68 Connector: HD68 

1x 36GB, 3MB/s, U2W SCSI without cable without cable without cable 

Connector: HD68 incl. description (Ger/US) incl. description (Ger/US) incl. description (Ger/US) 

without cable data and cleaning cartridge data and cleaning cartridge data and cleaning cartridge 

incl. description (Ger/US) 1.6 * 5.25", anthracite bezel 1.6 * 5.25", anthracite bezel 1.6 * 5.25", anthracite bezel 

data and cleaning cartridge max. 1x per system max. 1x per system max. 1x per system 

1.6 * 5.25", anthracite bezel 


E 




E PRIMERGY TX600 S3 Status 24.04.2006 

S26361-F3121-E173 S26361-F3121-E114 S26361-F3121-E130 

Hard disk 73GB Hard disk 146GB Hard disk 300GB 

10000rpm,

S y s t e m c o n f i g u r a t o r a n d o r d e r - i n f o r m a t i o n g u i d e 

F PRIMERGY TX600 S3 Status 24.04.2006 

Section V SCSI / RAID Controller 

A. on-board SCSI-/ RAID-Controller for accessible drives and SCSI HDD´s 

The system is equipped with a two channel Utra 320 onboard SCSI controller 

including a full featured RAID Controller with 256MB Cache (suporting the RAID level 0, 1, 5, 10, 50). 

As option the onboard RAID Controller can be equipped with a Battery Backup Unit. 

This onboard SCSI/RAID controller can be used for the connection of internal tapes and disks drives. 

Also one channel can be used for the connection of external Tape devices in the SX10 subsystem. 

The following rules apply for the cabling: 

The cables for the connection of the onboard RAID controller to the disks in the system are includes in the base unit. 

If an internal tape is configured, an additional SCSI cable is needed. (see section "V Hard disk drives / Tapes" ) 

For the connection of external Tape devices to the on board SCSI controller, also an additional cable is needed in the system. 

(plus cable to connect to the subsystem SX10, see configurator SX10) 

S26361-F3128-E20 

ROM Battery Backup Unit 

for on board RAID controller 


S26361-F3128-E102 

external 

SCSI-connection 

plug: 

1x VHDCI / UHD68(S) 


B. SCSI - controller for internal and external devices. 

S26361-F2399-E1 

1-channel SCSI U160 Controller 

Adaptec 29160 

plug: 

internal: HD 50-pin & HD68 

max. 2x external: HD68 

without 

cable 

64/66 PCI 

3.3V and 5V tolerant signaling 


C. RAID-Controller for external Disk Arrays 

S26361-F3006-E128 

2-channel RAID Controller U320 

LSI 

320-2 

128MB SDRAM ECC Cache The RAID controller can be used only for 

max. 2x default with TBBU the connection of external subsystems (SX30) 

plug: internal 2x HD68; Cables for the connection from the RAID Controllers 

external: 2x VHDCI to the subsystem see configurator SX30. 

without 

cable 

64/66 PCI controller, 180mm 

3.3V and 5V tolerant signaling 


G 

F u j i t s u S i e m e n s C o m p u t e r s 

Enterprise Products - PRIMERGY Server 1 2 o f 1 6


G PRIMERGY TX600 S3 Status 24.04.2006 

Section VI Fibre channel controller 

Qlogic controller Emulex Controller 

No mix and match for Qlogic and 

S26361-F3097-E1 Emulex Fibre channel controllers 

2GBit/s FC Controller possible 

Qlogic 

QLA2340, full height bracket 

1 channel 2GBit/sec FC Controller 

LC Interface for 50µm Fiber 

PCI-X 64Bit / 133MHz, 170mm 

3.3V / 5V tolerant signaling 

Qlogic controller max. 3x per system 

max. 3x or 

Emulex 

controller 

max. 

4x 

S26361-F3141-E1 S26361-F3306-E1 S26361-F3306-E2 

2GBit/s FC Controller 4GBit/s FC Controller 4GBit/s FC Controller 

Emulex Emulex Emulex 

LP1050Ex, full height bracket LPe1150, full height bracket LPe11002, full height bracket 

1 channel 2GBit/sec FC Controller 1 channel 4GBit/sec FC Controller 2 channel 4GBit/sec FC Controller 

LC Interface for 50µm Fiber LC Interface for 50µm Fiber LC Interface for 50µm Fiber 

PCIe x4, 111,2 x 167,7 mm² PCIe x4, 170mm PCIe x4, 170mm 


All controllers for the connection of external storage systems are delivered without cables. 

For the configuration of external cabling see the configurator for external storage systems. 

For Fibre Channel SAN also other componets like switches, SFPs and optical wires are 

orderable (for details see price liste) 

H 




H PRIMERGY TX600 S3 Status 24.04.2006 

Section VII Communication / Network 

on-board LAN Controller 

Dual Gbit Ethernet Contr. on-board Teaming: Failover, Load Balancing 

BroadCom BCM5704 The Intel LAN Controllers Pro 1000MT, 1000MF, 1000MT Dual Port Server 

can be used with the on-board controller in Teaming Mode 

ext: 2 x RJ 45 connector With Broadcom on-board adapters for Gigabit Ethernet must be used 

for the teaming the Broadcom driver. 

Two onboard LAN ports can likewise educate a team. 

A) Single Port LAN Adapter 

S26361-F3054-E1 

S26361-F3053-E1 

Gigabit Ethernet Contr. 1000SX Gigabit Ethernet Controller 1000TX 

Eth. Ctrl 1x1Gbit PCI-X Pro/1000MF LC Eth Ctrl 1x1Gbit PCI-X Pro/1000MT Cu 

Intel PRO/1000 MF Server Adapter Intel PRO/1000 MT Server Adapter 

PCI-X (PCI64/133), min 165 mm PCI-X (PCI64/133) 

ext:LC-connector ext: for RJ45-connector, Cat 5 


3x 

B) Dual Port LAN Adapter 

S26361-F3011-E1 

Gigabit Ethernet Controller Dual 1000TX 

Eth Ctrl 2x1Gbit PCI-X PRO/1000MT Cu 

Intel Pro/1000MT Dual Port Server Ad. 

PCI-X 

(PCI64/133) 

ext: for RJ45-plug, Cat 5 


C) Dual Port LAN Adapter PCIe x4 

while s t o c k s l a s t 

S26361-F3143-E1 

S26361-F3228-E1 

Gigabit Ethernet Contr. dual 1000TX Gigabit Ethernet Controller Dual 1000TX 

Eth. Ctrl 2x1Gbit PCIe PRO/1000P Cu Eth Ctrl 2x1Gbit PCIe PRO/1000PT Cu 

Intel Pro/1000P dual Server Adapter Intel Pro/1000PT dual Server Adapter 

4x PCIe x4, 170mm PCIe x4 

ext: for RJ45-plug, Cat 5 ext: for RJ45-plug, Cat 5 

connection with Cat 5 cabling max. 2x per system 

SW: VLAN, Fast & Gbit Etherchannel 


I 




I PRIMERGY TX600 S3 Status 24.04.2006 

Section VIII System Management Products (RemoteView) 

S26361-F1790-E221 

S26361-F2425-E103 

RemoteView Software V5.0 

RSB S2 LP 3HU 

Installation and configuration of RemoteView Service Board S2 

RemoteView Web and LAN FrontEnd Low Profile Version with 3 U bracket 

RSB, BMC-Manager, RTDS, FreeDOS for one standard PCI-slot 

and online manuals incl. cables and RV SW 


S26361-F2425-E305 

RSB S2 LP external power supply 

RemoteView Service Board S2 

low profile external power supply 

including power cable 

with Euro- and Euro socket connector 

Section IX Miscellaneous 

option for floorstand 

keyboards for floorstand versions for following countries: USB Keyboard: S26381-K340-E120 

S26381-K397-E110 USA / international KBPC PX D, professional keyboard 

S26381-K397-E120 

Germany 

S26381-K397-E140 

France 

S26381-K397-E155 Sweden / Finland 

S26381-K397-E165 United Kingdom 

S26381-K397-E180 

Spain 

S26381-K397-E185 

Italy 

Section X Power Cords 

The Floorstand version contains two power cords with German "Schuko" (CEE 7/7) connector 

as standard (S26361-F3151-L100). 

For shipments in other countrys, two of the following cables have to be ordered seperatly. 

16A CEE connector (IEC309, blue) 3.5 m 2x S26361-F3151-E200 

16A IEC320 C19 -> BS13/13 3.5 m 2x S26361-F3151-E400 

16A IEC320 C19 -> US NEMA L6-20 4.0 m 2x S26361-F3151-E500 

The Rack version contains two power cords with IEC320 C14 connnector (S26361-F3151-L350) 

With this cabel the system can be connected to UPS or power socket outlets with C14 connector. 

Attention: 

This power cord can be used only in 200-240V enironment 

due to the limitation of the C14 connector to 10A. 

In 110V eniroment, one of the following power cords must be used: 

For directly connection to a power socket outlet 3.5 m 2x S26361-F3151-E300 

or a UPS with 16A outlet (IEC320 C19) 

To connect the system outside of the rack in USA 4.0 m 2x S26361-F3151-E500 

In 200-240V enironment the following cables can be used as alternative: 

16A IEC320 C19 -> Schuko (CEE 7/7) 2.5 m 2x S26361-F3151-E100 

16A CEE connector (IEC309, blue) 3.5 m 2x S26361-F3151-E200 

16A IEC320 C19 -> BS13/13 3.5 m 2x S26361-F3151-E400 

16A IEC320 C19 -> US NEMA L6-20 4.0 m 2x S26361-F3151-E500 

Overview about all available power cords with 16A connnector: 

1x Power cord 16A IEC320 C19 -> Schuko (CEE 7/7) 2.5 m S26361-F3151-E100 

1x Power cord 16A IEC320 C19 -> 16A CEE (IEC309, blue) 3.5 m S26361-F3151-E200 

1x Power cord 16A IEC320 C19 -> 16A IEC320 C20 3.5 m S26361-F3151-E300 

1x Power cord 16A IEC320 C19 -> 10A IEC320 C14 2.5 m S26361-F3151-L350 

1x Power cord 16A IEC320 C19 -> BS13/13 3.5 m S26361-F3151-E400 

1x Power cord 16A IEC320 C19 -> US NEMA L6-20 4.0 m S26361-F3151-E500 

End PRIMERGY TX600 S3 





Cange Report 

Date Order number Changes 

2006-02-13 first draft

PRIMERGY TX600 S3

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?