Operating Instructions Blu-ray Discâ„¢ Player DMP ... - Panasonic

More documents

Recommendations

Info

Messages The following messages or service numbers appear on the television or unit’s display when something unusual is detected during startup and use. On the television Cannot play. � You inserted an incompatible disc. Cannot play on this unit. � You tried to play a non-compatible image. � Confirm “SD” on the unit’s display is not displayed and re-insert the card. No disc is inserted. � The disc may be upside down. $ This operation is not available. � Some operations are unsupported by the unit. For example; – BD-Video: During playback, reverse slow-motion or reverse frame-by-frame is not possible. IP address is not set. � The “IP Address” in “IP Address / DNS Settings” is “---. ---. ---. ---”. Set the “IP Address”, “Subnet Mask”, and “Gateway Address”. (Select the automatic address acquisition if necessary.) The wireless access point currently has a low network security setting. It is recommended to change to a higher setting. � Authentication type for the Wireless LAN is set to “Open system”, or the encryption type is set to “No encryption”. It is recommended to encrypt for safety reasons. For details, refer to the instructions of the Wireless router being used. Encryption is required when playing back video, etc., from DLNA compatible devices. On the unit’s display F99 � The unit fails to operate properly. Press [Í/I] on the main unit for 3 seconds to switch the unit to standby, then switch back on. HDMI ONLY � Some BD-Video discs can only be output with HDMI. NET � While connecting to a network. No PLAY � There is a viewing restriction on a BD-Video or DVD-Video. (� 30) No READ � The media is dirty or badly scratched. The unit cannot play. 38 VQT3B75 PLEASE WAIT � The unit is carrying out internal process. This is not a malfunction. You cannot operate the unit while “PLEASE WAIT” is displayed. REMOVE � The USB device is drawing too much power. Remove the USB device. SET � (“ � ” stands for a number.) � The remote control and main unit are using different codes. Change the code on the remote control. Press and hold [OK] and the indicated number button at the same time for more than 5 seconds. U59 � The unit is hot. The unit switches to standby for safety reasons. Wait for about 30 minutes until the message disappears. Select a position with good ventilation when installing the unit. Do not block the ventilation hole on the side of the unit. H�� or F�� (“ � ” stands for a number.) � There is something unusual. � Check the unit using the troubleshooting guide. If the service number does not disappear, do the following. 1 Disconnect the plug from the household mains socket wait a few seconds, then reconnect it. 2 Press [Í/I] to turn the unit on. (The unit may be fixed.) If the service number does not disappear despite doing the above, request service from the dealer. Inform the dealer of the service number when requesting service. START � The system is being restarted during the firmware update. Please do not turn off the unit. UPD�/� (“ � ” stands for a number.) � The firmware is being updated. Please do not turn off the unit. FINISH � The firmware update is complete.
Specifications Signal system: PAL/NTSC <strong>Operating</strong> temperature range: i5 oC to i35 oC <strong>Operating</strong> humidity range: 10 % to 80 % RH (no condensation) Video output: 1.0 Vp-p (75 ≠)/Pin jack:1 system Audio output: 2 Vrms (1 kHz, 0 dB)/Pin jack Number of connectors : 2 channel:1 system Digital audio output: Optical digital output (Optical terminal) HDMI AV output: Type A (19 pin) [BDT310] : 2 system [BDT210] [BDT110] : 1 system This unit supports “HDAVI Control 5” function. SD card slot: Connector : 1 system USB slot: USB2.0 : 2 system Ethernet: 10BASE-T/100BASE-TX : 1 system WLAN [BDT310] [BDT210] Antenna: Tx 1, Rx 2 Standard Compliance: IEEE802.11n / IEEE802.11a / IEEE802.11g / IEEE802.11b Transmission system: MISO-OFDM system, OFDM system, DSSS system Frequency range: IEEE802.11n / IEEE802.11a : 5.15 GHz to 5.35 GHz 5.47 GHz to 5.725 GHz IEEE802.11g / IEEE802.11b / IEEE802.11n : 2.4 GHz to 2.4835 GHz Transfer rate (standard)*: IEEE802.11n: Tx Max. 150 Mbps, Rx Max. 300 Mbps IEEE802.11g / IEEE802.11a: Max. 54 Mbps IEEE802.11b: Max. 11 Mbps Access Mode: Infrastructure mode Security: WPA2-PSK (TKIP/AES) WPA-PSK (TKIP/AES) WEP (64bit / 128bit) (This unit supports WPA and WPA2 encryption.) LASER Specification Class 1 LASER Product: Wave length: 790 nm (CDs)/655 nm (DVDs)/405 nm (BDs) Laser power:No hazardous radiation is emitted with the safety protection Power supply: AC 220 to 240 V, 50 Hz Power consumption: [BDT310] : Approx. 13 W [BDT210] [BDT110] : Approx. 11 W Power consumption in standby mode: Approx. 0.2 W Power consumption in quick start standby mode: [BDT310] : Approx. 4.3 W [BDT210] [BDT110] : Approx. 3.3 W Dimensions (WkDkH) Including the projecting parts: 430 mmk185 mmk35 mm Mass: Approx. 1.6 kg Specifications are subject to change without notice. * Transfer rates are theoretical values; however, actual communication rate will vary according to communication environment or connected equipment. File format File format Extension Reference MP3 “.MP3”, “.mp3“ JPEG “.JPG”, “.jpg“ DivX MKV “.DIVX”, “.divx”, “.AVI”, “.avi” Subtitles text file “.SRT”, “.srt”, “.SUB”, “.sub”, “.TXT”, “.txt” “.MKV”, “.mkv” Subtitles text file “.SRT”, “.srt”, “.SSA”, “.ssa”, “.ASS”, “.ass” ID3 tags (Only titles and the names of artists) ≥ MOTION JPEG and Progressive JPEG is not supported. ≥ You may not be able to play back the file if you have edited the folder structure or the file name on a PC or other device. ≥ With certain recording states and folder structures, the play order may differ or playback may not be possible. Audio information ≥ The video file and subtitles text file are inside the same folder, and the file names are the same except for the file extensions. ≥ Some DivX and MKV file may not be played back, depending on the video resolution and frame rate condition. The audio output differs depending on which terminals are connected to the amplifier/receiver, and the settings on the unit. (� 31, Digital Audio Output) ≥ The number of channels listed is the maximum possible number of output channels when connected to amplifier/ receiver compatible with the respective audio format. Terminal HDMI AV OUT OPTICAL “Digital Audio Output” “Bitstream” “PCM” Outputs using original audio *1 Dolby Digital/ DTS Digital Surround BD-Video : 7.1ch PCM *1*2*3 DVD-Video : 5.1ch PCM Down-mixed 2ch PCM *1 When “BD-Video Secondary Audio” is set to “On”, the audio will be output as Dolby Digital, DTS Digital Surround or 5.1ch PCM. *2 [BDT110] : The maximum possible number of Dolby sound is 5.1ch PCM. *3 The audio output is amplified from 5.1ch or 6.1ch to 7.1ch depending on the DTS, Inc. specifications. VQT3B75 39 Reference
Page 1 and 2: The illustration shows the image of
Page 3 and 4: Getting started Safety precautions
Page 5 and 6: Control reference guide 1 Turn the
Page 7 and 8: ∫ Discs that cannot be played by
Page 9 and 10: STEP 2 : Connecting to an amplifier
Page 11 and 12: STEP 3 : Connecting to a broadband
Page 13 and 14: STEP 5 : Settings Easy Setting Afte
Page 15 and 16: � ≥ Refer to the operating inst
Page 17 and 18: HOME menu Major functions of this u
Page 19 and 20: Enjoying BD-Live or picture-in-pict
Page 21 and 22: Enjoying 3D video You can enjoy pow
Page 23: Playing music DVD CD USB (DVD-R/-R
Page 26 and 27: 6 Press [3, 4, 2, 1] to select the
Page 28 and 29: Settings Playback menu 1 Press [DIS
Page 30 and 31: Setup menu Change the unit’s sett
Page 32 and 33: Display On-Screen Messages Choose w
Page 34 and 35: Remote Device Settings (� 26) Pre
Page 36 and 37: Picture The images from this unit d
Page 40: Supplemental information ∫ TV cod
Page 43 and 44: Information for Users on Collection

Operating Instructions Blu-ray Discâ„¢ Player DMP ... - Panasonic

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?