Cinema Referance Manual - Audio Design Associates

RISQUE DE CHOC ELECTRIQUE.
NE PAS OUVRIR
115 V
Auxiliary Input
Your last available input on a
Cinema Reference can be
automatically tied to one of
the following device input
labels:
AUXILIARY
CAMCORDER
VIDEOGAME
COMPUTER
PREAMP
MULTIROOM
The Cinema Reference is preprogrammed to permit you to easily
connect a tenth component. ADA has provided the “Out Of The
Box” setup with six input label that access Analog Input 3 and Video
Input 8. If you wish to connect either a:
Camcorder or
Video Game or
Computer or
Preamplifier or
Multi-Room System
If your tenth component does not match any of the above Input Label
names, ADA suggests using the Auxiliary Input Label name.
Please note, that you can only
use one of the Input Labels
for a single component. If
you wish to use more than
one of these input labels, you
will need to proceed with the
“Custom Setup” instructions.
Connection 1
Simply connect one of these items using standard RCA interconnects
are used for the audio connection while a 75Ω coax cable is
used for the video connection.
Connection 1 - To the Cinema Reference’s Audio Input #3.
Connection 2 - To the Cinema Reference’s #6 Video Input.
Connection 2
Stereo
Audio Out
R L
Video
Out
AUXILIARY COMPONENT
The "Out Of The Box" Setup
permits one of the following devices to
be connected to the Cinema Reference:
Aux, Camcorder, Video Game, Computer,
Preamplifier, or Multi-Room System.
Using the Custom Setup wll permit you to maximize
all available inputs for up to 15 components.
Video
Cable
VIDEO INPUTS
VIDEO OUT
1 3 5
87
1 REC
2 4 6 8 2 OSD
AUDIO INPUTS
1 2 3 4 5 6
L
L
L
3L
R
R
R
3R
OFF ON DC Input Mute Switch
1
LASER DISC PLAYER
Dolby Digital (AC-3)
RF Switcher & AC-3
2
RF Demodulator
S-VIDEO OUT S-VIDEO INPUTS
MAIN REC 1 2 3 4
AUDIO OUTPUTS
7 8 REC L LS SUB
L
R
OUT R RS C
Connections!
In order to play an AC-3 Laser
Disc, you must connect the Digital
AC-3 Output to a Digital Audio
Input (RCA Type Coax) below.
Y
HDTV/RGB
COMPONENT
VIDEO
Cr
SWITCHER
Use With DVD
Players or
Digital Video
Cb
Tape Players
1 2 OUT
DIGITAL AUDIO INPUTS
In order to play an AC-3 Laser Disc, 1 3
you must connect the Digital AC-3
Output to a Digital Audio Input.
OPTICAL INPUTS
1 2 3
2 4
Cinema Reference
15Manufactured under license from Dolby Laboratories Licensing Corp.
"Dolby", "Dolby Digital", "Pro Logic", & the Double-D Symbol are the trademarks of Dolby Laboratories Licensing Corp.
Manufactured under license from DTS Technology, LLC. DTS Digital Surround is a trademark of DTS Technology LLC.
Manufactured under license from Lucasfilm Ltd. U.S. patent numbers 5,043,970; 5,189,703; and 5,222,059.
Foreign patents pending. Lucasfilm and THX are registered trademarks of Lucasfilm Ltd.,
WARNING! Risk Of Hazardous Energy!
CAUTION
Make Proper Connections.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVERTISSEMENT! Energie Electrique Dangereuse!
Faire Des Connexions Propres Pour L'Hautparleur.
ATTENTION!
Voir La Notice De Fonctionnement.
MADE IN U.S.A.
LOW VOLTAGE
DATA PORT 12VDC OUT
Serial Data 100mA Max Per
ADA Bus DC 1 DC 2
1 2 3 4 1- 2+ 1- 2+
CAUTION: Disconnect Supply Cord Before Servicing.
ATTENTION: Debrancher Avant Le Depannage.
AC OUTPUT
10A Max Switched
AC INPUT
115V-60Hz/230V-50Hz
Voltage
Selector &
Safety Fuse
On This Side
115V
230V
Use Same
Value Fuse
115V-1AS.B.
230V-.5AS.B.
Stereo AudioCable
(This cable carries standard 2 channel audio)
Page 31