Version June 2013 - New Holland PLM Portal

Version
June 2013
AgGPS 252 receiver
NH 252 receiver
AFS252 receiver
AgGPS 262 receiver
NH 262 receiver
AFS262 receiver
AgGPS 372 receiver
NH 372 receiver
AFS 372 receiver
AgGPS 162 receiver
NH 162 receiver
AFS162 receiver
Appearance
Software version
bf_370.img
AgGPS262_5_01_001_4.img
(Software includes improvements for VRS
and OmniStar performance – helps to
reduce dropouts)
- RTK Age threshold increased from 40
seconds to 60 seconds
- xFill is NOT supported on 262
Ag372_2_01_002_4.img
(Software includes improvements for
VRS performance – helps to reduce
dropouts)
- xFill will be supported in the next
version of the 372
ahi_1_01_000_4_162.img
The version below is available but only corrects a small bug:
ahi_2_17_004_4.img
Software
Download Tool
Flashloader 200 (V3.34 or higher)
Configuration
EST availability
(V7.6.0.0)
GPS Remote software or by screen of your application (EZ-guide plus, EZ-guide 500, SWCD,CODI,FRED)
Configure AORE(120) or IORW(126) to heed health and all the rest to disabled
For OmniStar configure the receiver to “ESAT”. On some receivers it may be necessary to configure the satellite frequency manually (1539.9125 MHz/Baud Rate: 1200bps) (Europe Only).
For RTX CentrePoint (Sat) configure the receiver to 1539.9525 MHz and baud rate 600bps. This configuration should be done in RTK Config menu & NOT the DGPS Config menu in the RDI
screen (Europe Only).
Firmware version : Yes
Download/ConfigTool:Yes
“Intellisteer/Accuguide Autoguidance System II / Precision Farming / GPS” – Additional tools
(To be able to use the 162 receiver for
autoguidance (Egnos), you will need to
unlock the 162)
Cable / Tool
380002422
or
87298129/73316783/ZTN50166 is the big one (7 meter) Or alternatively: ZTN68463 (data output cable 262/162)

EZ-guide 500 screen EZ-guide 250 screen FM750 FM1000
Appearance
Software version
Ezg500_5_10_038_4.img
Languages: *.lpf
ezg250_3_10_038_4.img
Languages: *.lpf
cfx750_4_05_009_4.img
Languages: *.lpf
V4.00 - xFill, RTX RangePoint & FIQ Boom Height
Control System are supported.
V4.01- corrects a bug for EZ-Pilot and EZ-Steer
systems that was introduced in V4.00.
No language files for V4.01.
V4.05 - corrects a bug that caused RTK
frequencies to be lost.
- also corrects an issue that prevented
the APN settings being adjusted
through the display
First install monitor v. 1.17
"cfx750_mon_1_17.mnc" if FM750 is >>Trimble Support Page
Firmware version & Language Files (FM750): ASIST>>>Trimble Support Page
Cable / Tool
USB Device: Lexar firefly 1GB (P/N ZTN64268-00)

062/Garmin antenna NH/AFS 100/110/134 EZ-guide plus screen Field Manager display
Appearance
Software version
No Software Available
NH/AFS100 : CF_306.tnr
NH/AFS110 : SS_306.tnr
NH/AFS134 : BT_306.tnr
EZGPlus4.11.004-EU6.ROM
v5.20 (Upgrade, autorun, cougar)
Software
Download Tool
[No Software Available]
Flashloader 100
EZ-Toolbox software
Copy to Compact Flash Card
( Copy the upgrade folder and
autorun/cougar-files)
SNSRCFG_320.exe
Configuration
- Ensure baud rate is configured to 38400bps
- NMEA 2.30 mode is set to ON
- FIX + DGPS + DIFF mode is set to AUTO
- Only NMEA sentences “GPGGA, GPGSA,
GPVTG, GPGSV” should be selected for good
communication with the display
GPSRemote software or
by screen of your application
(EZ-guide plus, EZ-guide 500, SWCD,CODI)
Configure AORE(120) or IORW(126) to heed
health and all the rest to disabled
Through display
Through display
Password: 2005
Firmware version : No
Firmware version : Yes
Firmware version : Yes
EST availability
(v7.0)
Download/ConfigTool:Yes
“Intellisteer/Accuguide Autoguidance System II
/ Precision Farming / GPS” – Additional tools
Download/ConfigTool:Yes
“Intellisteer/Accuguide Autoguidance System II /
Precision Farming / GPS” – Additional tools
Download/ConfigTool:Yes
“EZ guide plus lightbar guidance system” –
Additional tools
Firmware version:
ASIST>>>Trimble Support Page
Cable / Tool
380002422 AND 380003304
277885A1 OR 87418417
Null modem cable
ZTN59043 OR 87297613 (in kit) CF Card+adapter: P/N : 84396507

Intellisteer/Accuguide Trimble autopilot EZ-steer
EZ-steer 500
EZ500 EZ250 FM750
FM1000
EZ-Pilot
Appearance
Software
version
Display AutoGuidance SW
CNH NAV SW
v12.x
ceres_cnh_v_3_27.img
v16.4 ceres_cnh_v_3_35.img
V25.6 3.57 (3.72)
V26.5 3.65 (3.72)
V27.2 3.72
V27.3-4
3.75 (New steering Cal logic for CCH)
V27.5 3.78
V28.1 3.80 (sudden XTE jump fix)
V28.2 3.82
V28.4 (lang28.5) 3.85 (AG715 RTK Radio Channel Fix)
Receiver/Display
SW
EZ-Guide Plus
EZ500 (V3-3.06)
EZ500 (V5.10)
FM1000 (V4.00)
FM750 (V4.01)
Trimble NAV SW
v.4.52
V5.15/V5.16
V5.26
VDB4.3
V5.26
VDB4.3
SCM_3_0_1.app SCM_4_1_0.app No Software Available
Software
Download
Tool
- If installing V3.82 or higher on a CCH tier 4
tractor with a class 5 axle ensure the UCM
software is updated to V1.07.00.00 or
higher to ensure the NAV controller uses
the correct steering pot slope.
- Software bug with V28.4 AG language files
so use V28.5 AG language files. Update
patches are on the EST Support page.
FlashLoader 200
When updating the NAV to V5.25 or
V5.26 ensure the following process is
followed:
1. Load default vehicle with AP Toolbox
2. Upgrade the NAVII firmware
3. Choose a profile from VDB list V4.3
4. Recalibrate the system
EZ-Toolbox software
N/A
Configuration
Intellisteer/AccuGuide:
For more configurations: use Autopilot
Toolbox II
“Trimble Brand Autoguidance
systems”Additional tools
FM750 / EZ500 / EZ+ use EST:
Autopilot Toolbox
“Trimble Brand Autoguidance
systems” – Additional tools
FMD + FM1000: in display config
Through display
Through display
Through display
EST
availability
(v7.6.0.0)
CNH NAV Software version : Yes (3.03, 3.27, 3.57, 3.65, 3.78, 3.80, 3.85)
Download/ConfigTool:Yes
Trimble NAV Firmware version and VDBlist
4.3: ASIST>>>Trimble Support Page
Is also possible without cable
Firmware version : Yes
Download/ConfigTool:Yes
“EZ guide plus lightbar guidance system” –
Additional tools
N/A
Cable / Tool
Serial cable e.g. from
EST box
380001593
380002422
To support all ages of IS/AG vehicles it will be necessary to order each of
the three cables above.
Serial cable e.g. from EST box
Note: For CNH Hybrid Installations the cables in the cell to the left will be required for software
download to the Trimble Autopilot Controller
N/A

AgGPS 450 Radio PDL 450 Radio TDL 450 Radio AG-715 Radio AgGPS RTK 450/442/542 Base
Appearance
Software
version
v1.30 AgGPS450_v130Upgrade.zfimg
v1.32 (required for (410-470MHz)
radio: 55560-45
AgGPS450_v132Upgrade.zfimg
Software
Download
Tool Flashloader 200
or
v2.42 V3.04.2881 N/A
TDL Conf V3.02
No Software Download
PDL Conf v.4
v3.67 (not for 542 base)
V4.60 (is valid for 542 base and for 450 base)
Configuration
EST
availability
(v7.6.0.0)
Winflash software
(Select “Sitenet 450 Transceiver”)
(Press Ctrl+Insert to insert new software
if not available yet)
(for download set-files: use Winflash)
Firmware version : Yes
Download/ConfigTool: Yes
“Intellisteer/Accuguide Autoguidance
System II / Precision Farming / GPS” –
Additional tools
Choose generic CMR radio in EZ 500
when used as rover radio for EZ 500
(In EZ 500 for RTK security: choose
Trimble radio: configure secure code,
and then choose generic CMR radio)
Firmware version : Yes
Download/ConfigTool: Yes
Set Files loaded with TDL
Conf Tool.
Configurations can be
done with TDL Conf or
using UI on the radio
Firmware version : No
Download/ConfigTool:
ASIST>>>Trimble Support
Page
AgRemote software or by
using the RDI screen
Note: No set-file is required.
Frequencies are configured
in the AgRemote/RDI tool.
In some cases it may be
necessary to use the Ag
Remote tool to configure
the radio for the first time.
After this it is possible to use
the RDI screen.
Firmware version : Yes
Download/ConfigTool: Yes
Winflash
(Select “Trimble AgGPS Receiver”)
(for download set-files: use Winflash)
Winflash-tool 1.212 required to connect to 542-base.
Install: "WFC-AgGPS-V460.exe"
(Download from Asist > Autoguidance support (Tool)
Firmware version : No
Download/ConfigTool:Yes/ Not in EST for 542
base
“Intellisteer Autoguidance System II / Precision
Farming / GPS” – Additional tools
Cable / Tool
Both tools required:
380002422 + 380002886
Together with PDL 450 radio (=
power cable)
Together with TDL 450
radio (= power cable) 380002422
Nullmodem cable
ZTN59043 OR 87297613
(in kit)

EZ-boom Field IQ/Yield Monitoring/Generic Rate Controller DCM-300 Modem
Appearance
Software
version
Software
Download
Tool
TR_EZBOOM-1_5.fw2
Display MSB 1 12 SSB 2 RWCM 3 SIM 4 SCM 5 RSCM 6 SMM 7 MSM 8 YMM 9
FM1000 >V7.1 V3.05 V3.05 V3.05 V3.05 V3.05 V3.06 V2.05 V1.11 V1.15
FM750
>V1.9 V2.06 V2.06 V2.06 V2.07 V2.07 V2.14 N/A N/A N/A
>V4.0 V3.05 V3.05 V3.05 V3.05 V3.05 V3.05 V2.02 V1.11 V1.15
EZ500 V5.10 V1.02 V1.02 V1.02 N/A V1.04 N/A N/A N/A N/A
CNH GRC GRC V28.4 V3.06 V3.06 V3.06 V2.08 V3.06 V3.08 V2.06 N/A N/A
EZ500: EZ Boom - Copy to USB (root). (EZ500 will work with Field IQ (but not recommended). SW update is not possible. Use FM750/FM1000 for SW
Update.)
FM750 Copy to USB (root) – Not compatible with EZ-Boom
FM1000 Included in display main firmware - FM1000 v5 or higher NOT compatible with EZ-boom and TAC
EZguideplus: EZ-toolbox – Not compatible with Field IQ
FMD Copy to Flash Card under Firmware folder - Not compatible with Field IQ
CNH GRC Use EST – Planting & Seeding Equipment>>IntelliRate Control/AFS AccuControl System and Aftermarket ISOBUS Implements
Through display:
V4.00 (Recommend Minimum Version for VRS)
V5.01 (Recommended Minimum Version for
Telematics modem)
Install NAV V3.72 and V27.2 (AG+PF) as a
minimum when using DCM300 modem with
Intellisteer/AccuGuide
Software Downloads are over-the-air (OTA)
Submit an ASIST report or contact local support
with modem serial number and request the
update.
A VRS modem can also be updated to V5.01 if
necessary; however on some modems the
Client IP address may need to be configured to
ensure the modem is connected to the correct
server for the OTA update.
Configuration
FMD – EZ-Boom Only
FM750 – Field IQ Only
EST
availability
(V7.6.0.0)
Firmware version:
For Trimble Field IQ: ASIST>>>Trimble Support Page
For CNH GRC: Ensure EST 7.6.0.0 Update 1 is installed on the EST laptop
Trimble WebService Tool
Firmware: N/A
Configuration: Instructions for WebService
Tool in EST
Cable / Tool
Connect to the modem with WiFi laptop
For Trimble FIQ: USB Device (Lexar firefly 1GB (P/N ZTN64268-00))
For CNH GRC: EST Dearborn DPA5 Tool
Note1: The software filenames below are an example of the filename spelling and is not necessarily the latest/correct version for the controller in all cases.
Note2: Filenames for CNH Generic Rate Controller (GRC) will have the file extension .hx1
MSB 1 – Master Switch Box – FIQ_12_Section_Switch_Module_2_06.ohr
12 SSB 2 – 12 Section Switch Box – FIQ_Master_Switch_Module_2_06.ofr
RWCM 3 – Rawson Control Module – FIQ_Rate_and_Section_Control_Module_2_14.ohk
SIM 4 – Switch Interface Module – FIQ_Rawson_Control_Module_2_06.orn
SCM 5 – Section Control Module - FIQ_Section_Control_Module_2_07.omg
RSCM 6 – Rate & Section Control Module - FIQ_Rate_and_Section_Control_Module_2_14.ohk
SMM 7 – Seed Monitor Module - FIQ_Seed_Monitoring_Module_2_05.okn
MSM 8 – Moisture Sensor Module - FIQ_Moisture_Sensor_Module_1_11.oms
YMM 9 – Yield Monitoring Module - FIQ_Yield_Monitoring_Module_1_15.odu