h Technical Product Data Gravity Pipe Systems PN 1 - Hobas

More documents

Recommendations

Info

DN Structural Adapters DN 1100 - 3600 Structural adapter, sand covered (TYPE E) Structural adapter, sand covered with thrust ring (TYPE F) Structural adapter, sand covered with collar (TYPE G) It consists of a modified pipe with sanding, on request also with a thrust ring or masonry collar. The standard length is 0.5 or 1 m up to DN 1100 and 0.5 or 1.5 m for DN 1200 according to national standards. Other lengths available on request. de a b d h L [mm] [mm] [mm] [mm] [mm] [mm] 1100 1099 80 12 29 100 500/ 1500 1200 1229 80 12 30 100 500/ 1500 1280 1280 80 12 32 100 500/ 1500 1350 1350 80 12 34 100 500/ 1500 1400 1434 100 15 35 100 500/ 1500 1500 1499 100 15 38 100 500/ 1500 1535 1535 100 15 38 100 500/ 1500 1600 1638 120 15 39 100 500/ 1500 1700 1720 120 20 42 100 500/ 1500 1800 1842 120 20 45 120 500/ 1500 1900 1940 120 20 46 120 500/ 1500 2000 2047 120 20 49 120 500/ 1500 2100 2160 120 20 49 120 500/ 1500 2200 2250 120 20 50 120 500/ 1500 2400 2400 120 20 55 120 500/ 1500 2400 2454 120 20 55 120 500/ 1500 2500 2555 120 20 67 150 500/ 1500 3000 3000 150 20 67 150 500/ 1500 3600 3600 150 20 67 150 500/ 1500 All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express or implied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice. E03 ACCESSORIES
Properties/long-term values: Density Tensile elastic modulus (at 23°C) Tensile strength (standard) Tensile strength (locked design) Tensile strain (at break): < PN 10 Tensile strain (at break): ≥ PN 10 Poisson's ratio Compressive elastic modulus (at 23°C) Compressive strength Compressive strain (at break) Flexural modulus Flexural strength Flexural strain (at break) Circumferential strain at PN Circumferential strain at 1.5 x PN Temperature resistance Chemical resistance (pH range) Temperature expansion coefficient Thermal conductivity Heat capacity Material Data The laminate structure of HOBAS GRP Pipes may vary, depending on the requirements such as pressure class (PN), stiffness (SN) or longitudinal tensile strength. The material data in the table should therefore be considered as a giudeline. We can provide more accurate material data for specific pipes on request. The properties of the pipes manufactured, such as stiffness, ring deflection and longitudinal tensile strength are routinely checked as part of quality assurance. Geometric properties, such as wall thickness, outside diameter and liner thickness, are measured and checked to internal quality standards. Test procedures and regulations are defined in the applicable standards. You will find more detailed information about them and other material tests, such as abrasion, long-term values, hydraulic properties, chemical resistance, etc. in our brochure CC-GRP Pipes Features, Tests and Benefits. Characteristic properties for HOBAS GRP Pipes: Pressure wave propagation rate Roughness (to Colebrook White) k *Temperature up to 80°C on request **Higher/lower pH on request Material data Unit kg/m³ MPa MPa MPa % % - MPa MPa % MPa MPa % % % °C pH 1/K W/m/K kJ/kg/K m/s mm Orientation Circumferential Longitudinal 90 - 130 15 - 40 12000 - 18000 12000 - 18000 130 - 140 ~ 2000 10000 - 15000 10000 - 12000 1.2 - 1.5 0.25 1.8 - 2.0 1.0 - 1.4 ~ 0.3 ~ 0.25 1.2 - 1.5 200 80 - 100 90 - 100 1.8 - 2.0 10000 - 15000 - 120 - 140 15 - 40 1.6 - 2.2 1.0 0.2 - 0.3 - 0.3 - 0.4 - ≤ 40 * 1 - 10 ** 26 - 30 x 10-6 0.5 - 1.0 1.0 - 1.4 ~ 450 0.01 - 0.016 All figures quoted are values and may slightly vary due to manufacturing tolerances. The information and recommendations reflect the state of our knowledge at the time of publication/update. Therefore the provided data cannot be construed as an express or implied warranty. All details must be checked and if necessary agreed to in each individual case. HOBAS cannot accept any liability. This also applies to errors, omissions and changes to technical data without notice. F01 MATERIAL DATA
Page 1 and 2: h Technical Product Data Gravity Pi
Page 3 and 4: ○ Sewer systems ○ ○ Relining
Page 5: PIPES PIPE JOINTS FITTINGS ACCESSOR
Page 8 and 9: DN Diameter series Non-Pressure Pip
Page 10 and 11: Relining Pipes DN 750 - 1500 Relini
Page 12 and 13: DN DN Th* A BL DN DN Th* A BL B/H [
Page 14 and 15: Jacking Pipes de 530 - 752 GRP jack
Page 16 and 17: Jacking Pipes de 1229 - 1535 GRP ja
Page 18 and 19: de [mm] SN SN SN SN SN SN SN SN SN
Page 20 and 21: Special Couplings The assembly coup
Page 22 and 23: 11,25° 15° 22,5° 30° 45° 60°
Page 24 and 25: DN 2 150 200 250 300 350 400 500 60
Page 26 and 27: DN 1 Y-Piece DN 150 - 700 It can be
Page 28 and 29: Saddle - glued DN 200 - 400 Saddles
Page 30 and 31: Saddle- screwed DN 300 -700 GRP Vit
Page 32 and 33: de1 de2 L de2 L de2 L de2 L [mm] [m
Page 34 and 35: de L D k d2 b DN n* Screws [mm] [mm
Page 36 and 37: Standard Manhole consisting of: 1 A
Page 38 and 39: Masonry Coupling DN 150 - 1000 Maso
Page 40 and 41: Manhole Liner Manhole liners are ma
Page 44: HOBAS Engineering Austria Pischeldo

h Technical Product Data Gravity Pipe Systems PN 1 - Hobas

Create successful ePaper yourself

Delete template?

Save as template?