hOLe SAWS

DIAMETERS OF THE HOLE SAWS tct - tc - td
ULTRA ® Code ULTRA ® Code Ø (mm) Ø (Inch) ULTRA ® Code Ø (mm) Ø (Inch) Fitting mandrel
TC 14 14,3 9/16
TC 16 15,9 5/8
TC 17 17,5 11/16
TCT 19 TC 19 19 3/4 TD 19 19,5 3/4
TCT 21 TC 21 20,7 13/16
TCT 22 TC 22 22,2 7/8 TD 22 22,7 7/8
TCT 24 TC 24 23,8 15/16
TCT 25 TC 25 25,4 1 TD 25 25,9 1
TCT 27 TC 27 27 1 1/16
TCT 29 TC 29 28,6 1 1/8 TD 29 29,1 1 1/8
TCT 30 TC 30 30,2 1 3/16
TCT 32 TC 32 31,8 1 1/4
TCT 35 TC 35 34,9 1 3/8 TD 35 35,2 1 3/8
TC 37 36,5 1 7/16
TCT 38 TC 38 38,1 1 1/2
TCT 40 TC 40 39,7 1 9/16
TCT 41 TC 41 41,3 1 5/8
TCT 43 TC 43 42,9 1 11/16
TCT 44 TC 44 44,5 1 3/4 TD 44 44,7 1 3/4
TC 46 46 1 13/16
TC 48 47,6 1 7/8
TCT 51 TC 51 50,8 2 TD 51 50,1 2
TCT 54 TC 54 54 2 1/8 TD 54 54,3 2 1/8
TCT 57 TC 57 57,2 2 1/4 TD 57 57,5 2 1/4
TCT 60 TC 60 60,3 2 3/8
TCT 64 TC 64 63,5 2 1/2
TCT 65 TC 65 65,1 2 9/16 TD 65 65,4 2 9/16
TC 67 66,7 2 5/8 TD 67
TCT 70 TC 70 69,9 2 3/4
TC 76 76,2 3 TD 76 76,4 3
TCT 79 TC 79 79,4 3 1/8
TCT 83 TC 83 82,6 3 1/4 TD 83 83 3 1/4
TCT 89 TC 89 88,9 3 1/2
TCT 92 TC 92 92,1 3 5/8
TCT 95 TC 95 95,3 3 3/4
TCT 102 TC 102 101,6 4 TD 102 102 4
TCT 105 TC 105 104,8 4 1/8
TC 111 111,1 4 3/8
TC 114 114,3 4 1/2
TC 127 127 5
TCT 152 TC 152 152,4 6
TC1
or TC2R
TC3
Accesories for hole saws TCT - TC - TD
Types Characteristics ULTRA ® Code
Same as SC 1 but fitted with a carbide tip drill ø 6.35 mm (1/4”) - SC 8. TC 1
Same as SC 2 R but tipped with a carbide tip drill ø 6.35 mm (1/4”) - SC 13.
TC 2 R
Same as SC 3 but fitted with a carbide tip drill ø 6.35 mm (1/4”) - SC 13. TC 3
Carbide sharpened tip pilot drill for mandrel TC 1 ø 6.35 mm (1/4”). L = 117 mm. SC 8
Carbide sharpened tip pilot drill for mandrel TC 2R - TC 3 ø 6.35 mm (1/4”). L=80 mm. SC 13
23
Hole saws kits ➥ See on page 26