METAL WALL PANELS 07 42 13 - McElroy Metal

More documents

Recommendations

Info

METAL WALL PANELS 07 42 13 ® • R-Panel - A multi-use wall and roof panel used primarily in pre-engineered metal building applications • U-Panel -This wall and roof panel is also used extensively as a liner or partition panel SIZES Panel cover widths of 36" (914 mm) are standard for most wall panel products, with the exception of 5V Crimp, Multi-Cor and M-Cor. See Table 5. COLOR, FINISHES Colors shown in Table 2 are supplied standard or optional according to panel model. Consult the manufacturer’s color chart online at www.mcelroymetal.com. Galvalumeª panels are available with the Kynar 500ª/Hylar 5000ª based fluoropon 70% polyvinylidene fluoride (PVDF) paint system, which has been shown to perform better than polyester, siliconized polyester and plastisol coatings with regard to chalking and color change. See Table 3 to compare finish options by product. ACCESSORIES McElroy offers a complete selection of components and accessories, including trim, fasteners, translucent panels, closures, tape sealants, pop rivets, door track covers and roof and soffit panels. Visit www.mcelroymetal.com or consult McElroy Metal for details. LIMITATIONS Design consideration must be given to structural support, flashing and drainage systems. Consult manufacturer’s literature for detailed information on load and span tables, construction recommendations and installation procedures. 4. Technical Data APPLICABLE STANDARDS American Iron and Steel Institute (AISI) - 2004 Edition of the Cold Formed Steel Design Manual ASTM International • ASTM A653/A653M Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process • ASTM A792/A792M Standard Specification for Steel Sheet, 55% Aluminum-Zinc Alloy- Coated by the Hot-Dip Process • ASTM B209 Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate • ASTM D2247 Standard Practice for Testing Water Resistance of Coatings in 100% Relative Humidity • ASTM E108 Standard Test Methods for Fire Tests of Roof Coverings • ASTM E119 Standard Test Methods for Fire Tests of Building Construction and Materials • ASTM E1646 Standard Test Method for Water Penetration of Exterior Metal Roof TABLE 2 COLOR Regal White Light Stone Ash Gray Roman Blue Surrey Beige Charcoal Tudor Brown Evergreen Patrician Bronze Clay Autumn Red Ivory McElroy Metal, Inc. Matte Black Patina Green Dark Bronze Brite Red Regal Blue Teal Brandywine Colonial Red Sandstone Bare Galvalume Galvalume Plus Brite White Panel Systems by Uniform Static Air Pressure Difference • ASTM E1680 Standard Test Method for Rate of Air Leakage Through Exterior Metal Roof Panel Systems • ASTM G90 Standard Practice for Performing Accelerated Outdoor Weathering of Nonmetallic Materials Using Concentrated Natural Sunlight Underwriters Laboratories, Inc. (UL) • UL 263 Standard for Fire Tests of Building Construction and Materials • UL 580 Standard for Tests for Uplift Resistance of Roof Assemblies • UL 790 Standard Test Methods for Fire Tests of Roof Coverings • UL 2218 Standard for Impact Resistance of Prepared Roof Covering Materials TABLE 3 SUBSTRATE, FINISH Panel Type 5V-Crimp Mega-Rib Mini-Rib Multi-Cor M-Cor Gage 24, 26, 29 18, 20, 22, 24, 26 24, 26, 29 24, 26, 29 24, 26, 29 Standard substrate, to ASTM A792 Galvalumeª Galvalumeª Galvalumeª Galvalumeª Galvalumeª Alternate substrate, to ASTM A653 N/A Galvanized Galvanized Galvanized Galvanized Coating Kynar 500ª Kynar 500ª Kynar 500ª Kynar 500ª Kynar 500ª Siliconized polyester Siliconized polyester Siliconized polyester Bare Bare Bare Bare Panel Type Multi-Rib Multi-V R-Panel U-Panel Mesa Gage 22, 24, 26 24, 26 22, 24, 26, 26 24, 26, 29 24, 26, 29 Standard substrate, to ASTM A792 Galvalumeª Galvalumeª Galvalumeª Galvalumeª Galvalumeª Alternate substrate, to ASTM B209 Galvanized Galvanized Galvanized Galvanized N/A Alternate substrate, to ASTM A653 Coating Kynar 500ª, Kynar 500ª, Kynar 500ª, Kynar 500ª, Kynar 500ª® Siliconized polyester Siliconized polyester Siliconized polyester Siliconized polyester Bare Bare Bare Bare Panel Type Max-Rib Ultra Gage 24, 26, 29 Standard substrate, to ASTM A792 Galvalumeª Kynar 500ª Coating Kynar 500ª® SPEC-DATA ª and MANU-SPEC ª are registered trademarks of Reed Elsevier Inc. The ten part SPEC-DATA format conforms to the editorial style of The Construction Specifications Institute and is used with their permission. The manufacturer is responsible for technical accuracy. ©2008 Reed Construction Dataª. All Rights Reserved.
METAL WALL PANELS 07 42 13 ® TABLE 4 MEGA-RIB, MULTI-RIB, R-PANEL TECHNICAL PROPERTIES Test Air leakage, ASTM E1680 APPROVALS, LISTINGS 2004 Florida State Building Code, structural, non-structural ICC-ES Evaluation Report ER-5896 Miami-Dade Notice of Acceptance, (NOA) - NOA #07-1219.13, Expires 2013 Texas Department of Insurance Windstorm Approval Underwriters Laboratories, Inc. (UL) • Multi-Rib, R-Panel, 5V-Crimp, Mega-Rib, Max- Rib, U-Panel have been approved for use in the following Underwriters Laboratories, Inc. (UL) design numbers: P225, P227, P230, P237, P250, P259, P265, P266, P268, P508, P510, P512, P514, P516, P518, P701, P711, P712, P713, P717, P720, P722, P723, P726, P731, P732, P734, P736, P739, P740, P801, P815, P819, P824, P825, P828 Visit McElroy Metal, Inc., online at www.mcelroymetal.com to obtain technical bulletins, approvals and listings by various agencies. PHYSICAL/TECHNICAL PROPERTIES See Tables 4 and 5. Technical bulletins are available online at www.mcelroymetal.com. FIRE PERFORMANCE See Table 3. For additional fire resistive assemblies and component protection information, consult McElroy Engineering Department. 5. Installation PREPARATORY WORK Deliver products in manufacturer’s original, unopened, undamaged containers with identification labels intact. Inspect for damage or moisture and notify McElroy Metal, Inc., within 48 hours of discovery. A forklift or crane can be used to handle unopened bundles to 25' (8 m) in length. For forklift unloading, spread forks to maximum width and place at center line weight distribution of bundle. For crane unloading, use a spreader bar to evenly distribute the bundle’s weight. Do not use cable supports as they will damage the panels. When moving individual panels, grasp panel edges and carry lengthwise, parallel to the ground. Protect the finish from scratching or abrasion. Store bundled material dry and above ground. Do not use plastic tarp, but protect from weather conditions by other means. Allow for proper air circulation to prevent moisture buildup under the tarp. Elevate one end of the bundles to allow for moisture runoff. If panels Static Pressure Air Infiltration Air Infiltration Specimen Differential Rate Rate Mega-Rib, 26 gage - 6.24 psf (- 297 Pa) - 6.24 cfm/lf 0.011 cfm/sf Mega-Rib, 26 gage + 6.24 psf (+ 297 Pa) + 6.24 cfm/lf 0.007 cfm/sf Mega-Rib, 26 gage ± 1.57 psf (± 75.2 Pa) ± 1.57 cfm/lf 0.004 cfm/sf Multi-Rib, 26 gage - 6.24 psf (- 297 Pa) 0.007 cfm/lf 0.002 cfm/sf Multi-Rib, 26 gage + 6.24 psf (+ 297 Pa) 0.004 cfm/lf 0.001 cfm/sf Multi-Rib, 26 gage - 1.57 psf (- 75.2 Pa) 0.004 cfm/lf 0.001 cfm/sf Multi-Rib, 26 gage + 1.57 psf (+ 75.2 Pa) 0.000 cfm/lf 0.000 cfm/sf R-Panel, 26 gage - 6.24 psf (- 297 Pa) 0.011 cfm/lf 0.004 cfm/sf R-Panel, 26 gage + 6.24 psf (+ 297 Pa) 0.007 cfm/lf 0.002 cfm/sf R-Panel, 26 gage - 1.57 psf (- 75.2 Pa) 0.007 cfm/lf 0.002 cfm/sf R-Panel, 26 gage + 1.57 psf (+ 75.2 Pa) 0.001 cfm/lf 0.001 cfm/sf Test Susceptibility to Leakage, FM 4471 Specimen Rate Test Duration Result Mega-Rib, 24 gage Water Spray Leakage 5 gal/sf/hr 15 minutes Passed Water Depth Static Water Leakage 6" (152 mm) 7 days Passed Test Water Penetration, ASTM E1646 Static Pressure Test Water Specimen Differential Rate Duration Infiltration Mega-Rib, 26 gage 12.0 psf (575 Pa) 5 gal/sf/hr 15 minutes None Multi-Rib, 26 gage 12.0 psf (575 Pa) 5 gal/sf/hr 15 minutes None R-Panel, 26 gage 12.0 psf (575 Pa) 5 gal/sf/hr 15 minutes None McElroy Metal, Inc. become wet, remove all panels from bundles and dry each individually. Prolonged panel storage is not recommended. If conditions do not permit immediate installation, take extra care to protect sheets from developing rust or watermarks. Verify that site conditions are acceptable for installation. Do not proceed with installation until unacceptable conditions are corrected. Handle and store product according to McElroy Metal, Inc., recommendations. METHODS Install panels plumb, true and in correct alignment with structural framing in accordance with shop drawings and manufacturer’s instructions. Install panels in vertical installations using manufacturer’s noncorroding fasteners color matched to panel. Sight-exposed noncorroding fasteners color matched to trim are permitted. Replace products having other than minor finish damage. PRECAUTIONS Before ordering materials, have proposed installation reviewed by technical services staff. Protect installed products from damage by subsequent construction activities. Field cutting panels and driving of fasteners will create metal shavings. These must be removed from the panel surface. Failure to do so will cause rust stains on the panel surface and will void the warranty. BUILDING CODES Installation must comply with the requirements of all applicable local, state and national code jurisdictions. Current data on building code requirements and product compliance may be obtained from McElroy technical support specialists. 6. Availability & Cost AVAILABILITY McElroy Metal, Inc., has 10 manufacturing facilities and 20 service centers located throughout the United States to serve the construction market. Contact McElroy Metal, Inc., for more information. COST Project-specific cost information may be obtained from a local McElroy distributor or directly from McElroy Metal, Inc. 7. Warranty McElroy Metal, Inc., makes available limited warranties. For specific information regarding SPEC-DATA ª and MANU-SPEC ª are registered trademarks of Reed Elsevier Inc. The ten part SPEC-DATA format conforms to the editorial style of The Construction Specifications Institute and is used with their permission. The manufacturer is responsible for technical accuracy. ©2008 Reed Construction Dataª. All Rights Reserved.
Page 1: METAL WALL PANELS 07 42 13 ® McElr
Page 5: METAL WALL PANELS 07 42 13 ® McElr

METAL WALL PANELS 07 42 13 - McElroy Metal

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?