METAL WALL PANELS 07 42 13 - McElroy Metal

METAL WALL PANELS 07 42 13
®
TABLE 4 MEGA-RIB, MULTI-RIB, R-PANEL TECHNICAL PROPERTIES
Test
Air leakage, ASTM E1680
APPROVALS, LISTINGS
2004 Florida State Building Code, structural,
non-structural
ICC-ES Evaluation Report ER-5896
Miami-Dade Notice of Acceptance, (NOA) -
NOA #07-1219.13, Expires 2013
Texas Department of Insurance Windstorm
Approval
Underwriters Laboratories, Inc. (UL)
• Multi-Rib, R-Panel, 5V-Crimp, Mega-Rib, Max-
Rib, U-Panel have been approved for use in
the following Underwriters Laboratories, Inc.
(UL) design numbers: P225, P227, P230, P237,
P250, P259, P265, P266, P268, P508, P510, P512,
P514, P516, P518, P701, P711, P712, P713, P717,
P720, P722, P723, P726, P731, P732, P734, P736,
P739, P740, P801, P815, P819, P824, P825, P828
Visit McElroy Metal, Inc., online at www.mcelroymetal.com
to obtain technical bulletins,
approvals and listings by various agencies.
PHYSICAL/TECHNICAL PROPERTIES
See Tables 4 and 5. Technical bulletins are
available online at www.mcelroymetal.com.
FIRE PERFORMANCE
See Table 3. For additional fire resistive assemblies
and component protection information,
consult McElroy Engineering Department.
5. Installation
PREPARATORY WORK
Deliver products in manufacturer’s original,
unopened, undamaged containers with identification
labels intact. Inspect for damage or
moisture and notify McElroy Metal, Inc., within
48 hours of discovery.
A forklift or crane can be used to handle
unopened bundles to 25' (8 m) in length. For
forklift unloading, spread forks to maximum
width and place at center line weight distribution
of bundle. For crane unloading, use a
spreader bar to evenly distribute the bundle’s
weight. Do not use cable supports as they will
damage the panels.
When moving individual panels, grasp
panel edges and carry lengthwise, parallel to
the ground. Protect the finish from scratching
or abrasion.
Store bundled material dry and above
ground. Do not use plastic tarp, but protect
from weather conditions by other means. Allow
for proper air circulation to prevent moisture
buildup under the tarp. Elevate one end of the
bundles to allow for moisture runoff. If panels
Static Pressure Air Infiltration Air Infiltration
Specimen Differential Rate Rate
Mega-Rib, 26 gage - 6.24 psf (- 297 Pa) - 6.24 cfm/lf 0.011 cfm/sf
Mega-Rib, 26 gage + 6.24 psf (+ 297 Pa) + 6.24 cfm/lf 0.007 cfm/sf
Mega-Rib, 26 gage ± 1.57 psf (± 75.2 Pa) ± 1.57 cfm/lf 0.004 cfm/sf
Multi-Rib, 26 gage - 6.24 psf (- 297 Pa) 0.007 cfm/lf 0.002 cfm/sf
Multi-Rib, 26 gage + 6.24 psf (+ 297 Pa) 0.004 cfm/lf 0.001 cfm/sf
Multi-Rib, 26 gage - 1.57 psf (- 75.2 Pa) 0.004 cfm/lf 0.001 cfm/sf
Multi-Rib, 26 gage + 1.57 psf (+ 75.2 Pa) 0.000 cfm/lf 0.000 cfm/sf
R-Panel, 26 gage - 6.24 psf (- 297 Pa) 0.011 cfm/lf 0.004 cfm/sf
R-Panel, 26 gage + 6.24 psf (+ 297 Pa) 0.007 cfm/lf 0.002 cfm/sf
R-Panel, 26 gage - 1.57 psf (- 75.2 Pa) 0.007 cfm/lf 0.002 cfm/sf
R-Panel, 26 gage + 1.57 psf (+ 75.2 Pa) 0.001 cfm/lf 0.001 cfm/sf
Test Susceptibility to Leakage, FM 4471
Specimen Rate Test Duration Result
Mega-Rib, 24 gage Water Spray Leakage 5 gal/sf/hr 15 minutes Passed
Water Depth
Static Water Leakage 6" (152 mm) 7 days Passed
Test
Water Penetration, ASTM E1646
Static Pressure Test Water
Specimen Differential Rate Duration Infiltration
Mega-Rib, 26 gage 12.0 psf (575 Pa) 5 gal/sf/hr 15 minutes None
Multi-Rib, 26 gage 12.0 psf (575 Pa) 5 gal/sf/hr 15 minutes None
R-Panel, 26 gage 12.0 psf (575 Pa) 5 gal/sf/hr 15 minutes None
McElroy Metal, Inc.
become wet, remove all panels from bundles
and dry each individually.
Prolonged panel storage is not recommended.
If conditions do not permit immediate
installation, take extra care to protect
sheets from developing rust or watermarks.
Verify that site conditions are acceptable
for installation. Do not proceed with installation
until unacceptable conditions are corrected.
Handle and store product according
to McElroy Metal, Inc., recommendations.
METHODS
Install panels plumb, true and in correct alignment
with structural framing in accordance
with shop drawings and manufacturer’s
instructions. Install panels in vertical installations
using manufacturer’s noncorroding fasteners
color matched to panel. Sight-exposed
noncorroding fasteners color matched to trim
are permitted. Replace products having
other than minor finish damage.
PRECAUTIONS
Before ordering materials, have proposed
installation reviewed by technical services
staff. Protect installed products from damage
by subsequent construction activities.
Field cutting panels and driving of fasteners
will create metal shavings. These must be
removed from the panel surface. Failure to do
so will cause rust stains on the panel surface
and will void the warranty.
BUILDING CODES
Installation must comply with the requirements
of all applicable local, state and national code
jurisdictions. Current data on building code
requirements and product compliance may
be obtained from McElroy technical support
specialists.
6. Availability & Cost
AVAILABILITY
McElroy Metal, Inc., has 10 manufacturing
facilities and 20 service centers located
throughout the United States to serve the
construction market. Contact McElroy Metal,
Inc., for more information.
COST
Project-specific cost information may be
obtained from a local McElroy distributor or
directly from McElroy Metal, Inc.
7. Warranty
McElroy Metal, Inc., makes available limited
warranties. For specific information regarding
SPEC-DATA ª and MANU-SPEC ª are registered trademarks of Reed Elsevier Inc. The ten part SPEC-DATA format conforms to the editorial style
of The Construction Specifications Institute and is used with their permission. The manufacturer is responsible for technical accuracy. ©2008 Reed Construction Dataª. All Rights Reserved.