concealed - Truth Hardware

More documents

Recommendations

Info

15 ENTRYGARD® DUAL ARM OPERATOR TRUTH TIPS (con't): 2. If operator placement, as calculated in Figure #1, is not desirable, the operator can be shifted up to .343" (8.7 mm) away from the hinge side of the window. Shifting the operator will cause slightly higher operator torque and reduces resistance to wind load. If 90° of opening is not necessary, the operator can be shifted toward the hinge side of the window. The best operator performance can be achieved by minimizing dimensions “A” and “X” - see Figure 1. 3. When a Dual Arm Operator is installed in high rise applications over two stories, a Truth Limit Device, to restrict the amount of opening, is recommended. Contact Truth for wind load information. 4. Sash weight should be limited to 60 lbs. to insure ease of operation for the lifetime of the window. When used on a sash weighing over 60 lbs., operating torque will noticeably increase and operator life will be reduced. 5. Truth recommends that a Snubber be used at the center of the hinge side on any casement window which has a tendency to bow outward at the center in the closed position. Adding a Snubber may increase the negative air pressure rating of a casement window. 6. A Spline Cap (part #21306) is available to protect the operator splines from dirt and other windows from damage during shipping, installation and final building construction. 7. The Dual Arm Operator should not be used in conjunction with Butt Hinge or 4-Bar Hinges (except the #34.81). In most cases, the motion of the two operating arms do not complement the motion of these types of hinges resulting in higher operating torque. 8. The location of the operator and stud bracket (dimension A and B) is based on a sill cover width of 1.938" (23.8 mm) as specified in Figure. 1. If the sill cover depth must be increased, dimensions A & B will be decreased proportionately and operator torque may increase. 9. For accurate hardware placement in vinyl or metal applications, pre-drilling of the window profile is recommended. 10. For vinyl window applications, mounting screws should pass through two PVC walls, or one PVC wall and one insert wall. For this reason, it may be necessary to use a longer screw than is recommended. 11. For metal window profiles, Truth recommends machine screws. However, in most applications, sheet metal screws will provide adequate holding power. 12. When selecting mounting screws for Truth hardware, coating compatibility Is one of the most important criteria. For best corrosion resistance the coating on the screws should be the same as the coating on the hardware. For more information see Tech Note #11. INCLUDE TRUTH SPECS ON YOUR NEXT WINDOW PROJECT Window operators shall be provided which allow easy adjustment of window position. The mechanism should be crank operated and provide superior operation throughout the windows range of motion. Connection to the movable sash must be easily detachable for window cleaning and maintenance. Removable EntryGard® interior cover will allow matching hardware styling as well as easier finishing of frame and sill. Window operators will be of combined push arm and drag arm/link design driven by a hand crank. The operator must be constructed of E-Gard® components, hardened steel worm and gearing and high pressure zinc alloy die castings. High-strength plastic trim cover. Window operators shall be 15 series EntryGard® Dual Arm Operator as manufactured by Truth Hardware, Owatonna, MN. 27a
15 ENTRYGARD® DUAL ARM OPERATOR FIG. 1 APPLICATION OF TRUTH ENTRYGARD DUAL ARM OPERATOR TRACK 4.938 (125.4mm) 2.469 (62.7mm) STUD BRACKET SASH X FRAME HARDWARE SHOWN 15.10 OPERATOR 10339 STUD BRACKET 30473 TRACK 14.05 HINGE 10341 COVER 10579 HANDLE 1.521 (38.6mm) .417 (10.6mm) 10.750* (273.1mm) *15.15 = 11.500 (292.0mm) 5.220 (132.6mm) B A D 17.0 (431.8mm) APPROXIMATE MINIMUM SASH WIDTH (USING 14.05) 1.938 (49.2mm) .468 (11.9mm) MAX. WALL THICKNESS LEFT HAND SHOWN SASH .282 FRAME (7.1mm) AVAILABLE NOTE: 1.312 (33.3mm) HINGES 14.05 1. TO DETERMINE THE A DIMENSION FOR OPERATOR PLACEMENT 14.06 ADD SASH DIMENSION XTO HINGE CONSTANT Y ( A = X + Y ) 14.75 SEE TRUTH TIP NO. 8. 14.76 2. MINIMIZE THE XDIMENSION FOR BEST OPERATOR PERFORMANCE. 14.77 THE RECOMMENDED RANGE FOR DIMENSION XIS .250 (6.4mm) TO 1.0 (25.4mm). 14.80 3. NOT ALL DUAL ARM OPERATORS CAN BE USED WITH ALL HINGES. 14.91 CONSULT THE TABLE IN FIG. 2. 14.93 34.81 4. OPERATOR CUTOUT SIZE 5.0 (127.0mm) X .750 (19.1mm). 5. USE L, F, AND LINK THICKNESS TO CALCULATE MOUNTING HEIGHT. TABLE OF APPLICATION FOR 90° SASH OPENING Y HINGE CONSTANT 5.932 (150.7mm) 6.560 (166.8mm) 5.932 (150.7mm) 6.560 (166.8mm) 3.591 (91.2mm) 5.932 (150.7mm) 6.560 (166.8mm) 3.591 (91.2mm) 5.692 (144.6mm) F SEE FIG. 2 27b
Page 2 and 3:
Connecting Innovations In Hardware
Page 4 and 5:
Terms & Conditions of Sale TRUTH HA
Page 6 and 7:
13 AWNING HINGES APPLICATION OF CON
Page 8 and 9:
14 CONCEALED CASEMENT HINGE 4. Trut
Page 10 and 11:
14 CONCEALED CASEMENT HINGE FIG. 2
Page 12 and 13:
2e 700 WEST BRIDGE STREET, OWATONNA
Page 14 and 15:
14 THE MAXIM® SYSTEM CASEMENT HING
Page 16 and 17:
MAXI M 14 THE MAXIM® SYSTEM CASEME
Page 18 and 19:
HIGH PERFORMANCE CASEMENT HINGE 3.1
Page 20 and 21:
HIGH PERFORMANCE CASEMENT HINGE
Page 22 and 23:
HIGH PERFORMANCE CASEMENT HINGE
Page 24 and 25:
MAXIM HIGH PERFORMANCE PAGE CASEMEN
Page 26 and 27:
HIGH PERFORMANCE CASEMENT HINGE 19
Page 28 and 29:
HIGH PERFORMANCE CASEMENT HINGE 19
Page 30 and 31:
29 BUTT HINGES 29.10 BUTT HINGE .42
Page 32 and 33:
4-BAR HINGES GUIDE TO 4-BAR HINGE S
Page 34 and 35:
STANDARD & HEAVY DUTY 4-BAR HINGES
Page 36 and 37:
STANDARD DUTY 4-BAR HINGE (201SS Se
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
HEAVY DUTY 4-BAR HINGE (301SS Serie
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
STANDARD DUTY 4-BAR EGRESS HINGE (2
Page 50 and 51:
STANDARD DUTY EGRESS/WASHABILITY 4-
Page 52 and 53:
HEAVY DUTY 4-BAR EGRESS HINGES (333
Page 54 and 55:
HEAVY DUTY EGRESS/WASHABILITY 4-BAR
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
SUPERIOR 4-BAR HINGE provide the ne
Page 64 and 65:
700 WEST BRIDGE STREET, OWATONNA, M
Page 66 and 67:
SUPERIOR 4-BAR HINGE TRUTH SUPERIOR
Page 68 and 69:
37/99 SASH CONTROL DEVICES TRUTH TI
Page 70 and 71:
37/99 SASH CONTROL DEVICES FIG. F 3
Page 72 and 73:
37/99 SASH CONTROL DEVICES FIG. 7 A
Page 74 and 75:
SAFEGARD TM CASEMENT WINDOW OPENING
Page 76 and 77:
SAFEGARD TM CASEMENT WINDOW P OPENI
Page 78 and 79:
99 SNUBBERS FIG. 1 32939.XX CONCEAL
Page 80 and 81:
45 JAMB JACKS FIG. 1 INSTALLATION O
Page 82 and 83:
45 JAMB JACKS FIG. 5 JAMB JACK III
Page 84 and 85:
CASEMENT AWNING 16 NON-HANDED, LOW
Page 86 and 87:
16 NON-HANDED, LOW PROFILE SASH LOC
Page 88 and 89:
CASEMENT AWNING 16 HOMEGARD® SASH
Page 90 and 91:
16 HOMEGARD® SASH LOCK FIG. 1 16.5
Page 92 and 93:
CASEMENT AWNING 16 ENTRYGARD® SASH
Page 94 and 95:
16 ENTRYGARD® SASH LOCK FIG. 1 APP
Page 96 and 97:
CASEMENT AWNING 16 MIRAGE® CONCEAL
Page 98 and 99:
16 MIRAGE® CONCEALED MULTI-POINT L
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
CASEMENT AWNING 16 SENTRY 2000® MO
Page 110 and 111:
CASEMENT AWNING 24 LOCKING HANDLE 1
Page 112 and 113:
24 LOCKING HANDLE 16b FIG. 3 LOCKIN
Page 114 and 115:
B 24 LOCKING HANDLE 16d FIG. 7 APPL
Page 116 and 117:
24 LOCKING HANDLE 16f FIG. 9 KEEPER
Page 118 and 119:
CASEMENT AWNING 24 MAXIM® MULTI-PO
Page 120 and 121:
24 MAXIM® MULTI-POINT & SINGLE POI
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
M 24 MAXIM® MULTI-POINT & SINGLE P
Page 134 and 135:
CASEMENT AWNING 15 TEMPO LOCKS 17.1
Page 136 and 137:
TEMPO LOCKS FIG. 1 TEMPO MULTI-POIN
Page 138 and 139:
TEMPO LOCKS FIG. 3A TEMPO LOCKS TIE
Page 140 and 141:
TEMPO LOCKS FIG. 6 NON HANDED ADJUS
Page 142 and 143:
CASEMENT AWNING ENCORE MULTI-POINT
Page 144 and 145:
ENCORE MULTI-POINT LOCKING SYSTEM
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
CASEMENT 24 MULTI-POINT LOCKING SYS
Page 156 and 157:
24 MULTI-POINT LOCKING SYSTEM FIG.
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
CASEMENT 15 PUSH OUT HARDWARE 20.
Page 164 and 165:
PUSH OUT HARDWARE FIG.1CLASSIC
Page 166 and 167:
PUSH OUT HARDWARE &9=%!I#$.G%K9K ?%
Page 168 and 169:
PUSH OUT HARDWARE FIG.16FRENCH
Page 170 and 171:
PUSH OUT HARDWARE 6"67*6$8)* B"&*()
Page 172 and 173:
PUSH OUT HARDWARE FIG.2612.81
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
HANDLES& LOCKSETS MORTISELOCK
Page 180 and 181:
ASCENT EURO GROOVE LOCKING SYSTEM F
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
ASCENT EURO GROOVE LOCKING SYSTEM X
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
ASCENT EURO GROOVE LOCKING SYSTEM 7
Page 198 and 199:
AWNING 25 TRIMLINE CAM HANDLE LOCKS
Page 200 and 201:
25 TRIMLINE CAM HANDLE LOCKS P FIG.
Page 202 and 203:
25 TRIMLINE CAM HANDLE LOCKS FIG. 9
Page 204 and 205:
AWNING 25 POLE-OPERATED CAM HANDLE
Page 206 and 207:
25 POLE-OPERATED CAM HANDLE LOCKS F
Page 208 and 209:
AWNING 27 TRIMLINE CAM HANDLE WITH
Page 210 and 211:
27 TRIMLINE CAM HANDLE WITH CONCEAL
Page 212 and 213:
AWNING 27 POLE-OPERATED CAM HANDLE
Page 214 and 215:
27 POLE-OPERATED CAM HANDLE WITH CO
Page 216 and 217:
AWNING 28 KEY OPERATED CUSTODIAL LO
Page 218 and 219:
28 KEY OPERATED CUSTODIAL LOCK (REM
Page 220 and 221:
CASEMENT AWNING MAXIM ® SYSTEM OPE
Page 222 and 223:
CASEMENT MAXIM ® SYSTEM OPERATORS
Page 224 and 225:
MAXIM ® DUAL ARM OPERATORS (SILL M
Page 226 and 227:
MAXIM ® DUAL ARM OPERATORS (SILL M
Page 228 and 229:
MAXIM ® DUAL ARM OPERATORS (LOW PR
Page 230 and 231:
MAXIM ® DUAL ARM OPERATORS (LOW PR
Page 232 and 233:
MAXIM ® DYAD OPERATORS (SILL MOUNT
Page 234 and 235:
MAXIM ® DYAD OPERATORS (SILL MOUNT
Page 236 and 237:
MAXIM ® DYAD OPERATORS (LOW PROFIL
Page 238 and 239:
MAXIM ® REVERSE DYAD OPERATORS (SI
Page 240 and 241:
MAXIM ® REVERSE DYAD OPERATORS (SI
Page 242 and 243:
MAXIM ® REVERSE DYAD OPERATORS (LO
Page 244 and 245:
MAXIM ® SINGLE ARM OPERATORS (SILL
Page 246 and 247:
MAXIM ® SINGLE ARM OPERATORS (SILL
Page 248 and 249:
MAXIM ® SINGLE ARM OPERATORS (LOW
Page 250 and 251:
MAXIM ® SINGLE ARM OPERATORS (LOW
Page 252 and 253:
MAXIM ® AWNING OPERATORS (SILL MOU
Page 254 and 255:
MAXIM ® NARROW OPERATORS FIG. 1 AP
Page 256 and 257:
MAXIM ® NARROW OPERATORS (SILL MOU
Page 258 and 259: CASEMENT AWNING THE MAXIM ® SYSTEM
Page 260 and 261: MAXIM ® AWNING OPERATORS Hardware
Page 262 and 263: CASEMENT AWNING ENCORE SYSTEM OPER
Page 264 and 265: ENCORE SYSTEM OPERATORS ENCORE DUA
Page 266 and 267: ENCORE DUAL ARM OPERATOR (SILL MOU
Page 268 and 269: ENCORE DUAL ARM OPERATOR (SILL MOU
Page 270 and 271: ENCORE DUAL ARM OPERATOR (LOW PROF
Page 272 and 273: ENCORE DUAL ARM OPERATOR (LOW PROF
Page 274 and 275: ENCORE DYAD OPERATOR (SILL MOUNT)
Page 276 and 277: ENCORE DYAD OPERATOR (SILL MOUNT)
Page 278 and 279: ENCORE DYAD OPERATOR (LOW PROFILE)
Page 280 and 281: ENCORE REVERSE DYAD OPERATOR (SILL
Page 282 and 283: ENCORE REVERSE DYAD OPERATOR (SILL
Page 284 and 285: ENCORE REVERSE DYAD OPERATOR (LOW
Page 286 and 287: ENCORE SINGLE ARM OPERATORS (SILL
Page 288 and 289: ENCORE SINGLE ARM OPERATORS (SILL
Page 290 and 291: ENCORE SINGLE ARM OPERATORS (LOW P
Page 292 and 293: ENCORE SINGLE ARM OPERATORS (LOW P
Page 294 and 295: ENCORE AWNING OPERATOR (SILL MOUNT
Page 296 and 297: ENCORE SYSTEM OPERATORS FIG. 1 APP
Page 298 and 299: ENCORE SYSTEM OPERATORS FIG. 3 ENC
Page 300 and 301: MAXIM ® AWNING OPERATORS 25oo 700
Page 302 and 303: THE ENCORE SYSTEM OPERATOR ACCESSO
Page 310 and 311: 15 ENTRYGARD® DUAL ARM OPERATOR FI
Page 312 and 313: 15 ENTRYGARD® DUAL ARM OPERATOR FI
Page 314 and 315: 700 WEST BRIDGE STREET, OWATONNA, M
Page 316 and 317: 15 ENTRYGARD® DYAD OPERATOR TRUTH
Page 318 and 319: 15 ENTRYGARD® DYAD OPERATOR FIG. 2
Page 320 and 321: 15 ENTRYGARD® DYAD OPERATOR FIG. 5
Page 322 and 323: 15 ENTRYGARD® SINGLE ARM OPERATOR
Page 324 and 325: 15 ENTRYGARD® SINGLE ARM OPERATOR
Page 326 and 327: 11 ENTRYGARD® AWNING OPERATOR 5. A
Page 328 and 329: 11 ENTRYGARD® AWNING OPERATOR FIG.
Page 330 and 331: 700 WEST BRIDGE STREET, OWATONNA, M
Page 332 and 333: 15 ELLIPSE SINGLE ARM OPERATOR 7. A
Page 334 and 335: 15 ELLIPSE SINGLE ARM OPERATOR FIG.
Page 336 and 337: 15 ELLIPSE P SINGLE ARM OPERATOR FI
Page 338 and 339: 700 west bridge street, owatonna, m
Page 340 and 341: 15 ELLIPSE DYAD OPERATOR TRUTH TIPS
Page 342 and 343: 15 ELLIPSE DYAD OPERATOR FIG. 2 ELL
Page 344 and 345: 15 ELLIPSE DYAD OPERATOR FIG. FIG.
Page 346 and 347: 15 ELLIPSE SINGLE ARM AWNING OPERAT
Page 348 and 349: PAGE 3.23C; SCALE: 3:1 (.3333333 IN
Page 350 and 351: 700 west bridge street, owatonna, m
Page 352 and 353: 15 TRADITIONAL STYLE SINGLE ARM OPE
Page 358 and 359:
15 TRADITIONAL STYLE DYAD OPERATOR
Page 360 and 361:
Page 362 and 363:
Page 364 and 365:
15 TRADITIONAL STYLE SINGLE ARM AWN
Page 366 and 367:
15 TRADITIONAL STYLE SINGLE ARM AWN
Page 368 and 369:
700 west bridge street, owatonna, m
Page 370 and 371:
23 SINGLE ARM OPERATOR (FACE-MOUNT)
Page 372 and 373:
23 SINGLE ARM OPERATOR (FACE-MOUNT)
Page 374 and 375:
23 DYAD OPERATOR TRUTH TIPS (con't)
Page 376 and 377:
23 DYAD OPERATOR FIG. 2 DYAD OPERAT
Page 378 and 379:
23 DYAD OPERATOR FIG. 5 23.54 and 2
Page 380 and 381:
23 DYAD OPERATOR FIG. 8 STUD BRACKE
Page 382 and 383:
Page 384 and 385:
12 TELESCOPING PUSH BAR OPERATORS F
Page 386 and 387:
Page 388 and 389:
22 PIVOT SHOE OPERATOR Window opera
Page 390 and 391:
22 PIVOT SHOE OPERATOR FIG. 4 GASKE
Page 392 and 393:
22 SCISSORS ARM OPERATOR TRUTH TIPS
Page 394 and 395:
22 SCISSORS ARM OPERATOR FIG. 2 FRO
Page 396 and 397:
22 SCISSORS ARM OPERATOR FIG. 7 GAS
Page 398 and 399:
11 AWNING OPERATOR TRUTH TIPS (con'
Page 400 and 401:
11 AWNING OPERATOR FIG. 3 ROTO GEAR
Page 402 and 403:
Page 404 and 405:
10 LEVER OPERATOR 7. For metal wind
Page 406 and 407:
10 LEVER OPERATOR FIG. 5 SASH HOOK
Page 408 and 409:
42 MANUAL SKYLIGHT OPERATOR SYSTEM
Page 410 and 411:
Page 412 and 413:
Page 414 and 415:
Page 416 and 417:
SENTRY II WLS POWER WINDOW SYSTEMS
Page 418 and 419:
SENTRY II WLS POWER WINDOW SYSTEMS
Page 420 and 421:
Page 422 and 423:
SENTRY II HS MOTOR SYSTEM 46a Up to
Page 424 and 425:
SENTRY II HS MOTOR SYSTEM F FIG. 3
Page 426 and 427:
MARVEL POWER WINDOW SYSTEM light op
Page 428 and 429:
MARVEL POWER WINDOW SYSTEM (Snap Br
Page 430 and 431:
MARVEL POWER WINDOW SYSTEM (Snap Br
Page 432 and 433:
MARVEL POWER WINDOW SYSTEM (Pull Pi
Page 434 and 435:
99 STUD BRACKETS & TRACK FIG. 1 SIN
Page 436 and 437:
99 STUD BRACKETS & TRACK FIG. 9 STU
Page 438 and 439:
99 STUD BRACKETS & TRACK FIG. 17 ST
Page 440 and 441:
99 STUD BRACKETS & TRACK 48g 700 WE
Page 442 and 443:
99 ACCESSORY ITEMS FIG. 1 APPLICATI
Page 444 and 445:
99 ACCESSORY ITEMS FIG. 16 SPLINE C
Page 446:
99 ACCESSORY ITEMS FIG. 24 ADA OPER
show all

concealed - Truth Hardware

Create successful ePaper yourself

Delete template?

Save as template?