NEWS 2005 - Jan Havelka
NEWS 2005 - Jan Havelka
NEWS 2005 - Jan Havelka
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
KSCM Face Mills<br />
NEW<br />
Cutter Cartridge Assembly<br />
Tool configuration universal cartridge, 75° – face milling<br />
INSERTS<br />
1. Insert cartridges<br />
into the body.<br />
2. Screw in the<br />
clamping screws<br />
(RH), and tighten<br />
to 10 Nm.<br />
3. Screw in the<br />
adjusting screws<br />
(RH), and tighten<br />
to 3 Nm.<br />
4. Determine which<br />
cartridge is in the<br />
highest axial<br />
position.<br />
5. By turning the<br />
adjusting screws to<br />
the right, adjust the<br />
remaining cartridges<br />
for even running.<br />
Max. permitted<br />
run-out error 3 µm.<br />
-KSCMCA75UN<br />
FACE MILLING<br />
Tool configuration universal cartridge + finishing cartridge (ratio approx. 3:1), 75°<br />
END MILLING<br />
MILLING<br />
1. Insert universal<br />
cartridges at a<br />
ratio of approx.<br />
4:1 in the body.<br />
Make sure they<br />
are distributed<br />
evenly!<br />
2. Screw in the<br />
clamping screws<br />
(RH), and tighten<br />
to 10 Nm.<br />
3. Screw in the<br />
adjusting screws<br />
(RH), and tighten<br />
to 3 Nm.<br />
4. Determine<br />
which cartridge<br />
is in the highest<br />
axial position.<br />
5. By turning the<br />
adjusting screws<br />
to the right,<br />
adjust the<br />
remaining<br />
cartridges for<br />
even running.<br />
Max. permitted<br />
run-out error<br />
3 µm.<br />
-KSCMCA75QF<br />
Finishing<br />
cartridge<br />
-KSCMCA75UN<br />
Universal<br />
cartridge<br />
6. Insert finishing<br />
cartridges as<br />
described in steps<br />
1.–5., but with an<br />
axial advance of<br />
0,008 +0,002 mm.<br />
Max permitted<br />
run-out error of<br />
3 µm with finishing<br />
cartridges.<br />
SLOTTING / HELICAL<br />
Tool configuration edge cartridges, 90° – shoulder milling<br />
DIE & MOLD<br />
1. Insert cartridges<br />
into the body.<br />
2. Screw in the<br />
clamping screws<br />
(RH), and<br />
tighten to 10 Nm.<br />
3. Screw in the<br />
adjusting screws<br />
(RH), and<br />
tighten to 3 Nm.<br />
4. Determine which<br />
cartridge is in<br />
the highest axial<br />
position.<br />
5. By turning the<br />
adjusting screws<br />
to the right,<br />
adjust the<br />
remaining<br />
cartridges for<br />
even running.<br />
Max. permitted<br />
run-out error<br />
3 µm.<br />
-KSCMCA90UN<br />
B42<br />
To place an order, contact your Kennametal representative or visit www.kennametal.com.
Change language