How to build a cat enclosure - City of Tea Tree Gully

More documents

Recommendations

Info

Figure 6: Fixing light meshSewnin doorStructurecoveredwith nettingWallCement footingsSide ElevationFigure 7: Tubular steel enclosureFigure 8: Prefab pipe fittingFlange fixing to wallCross braceFront ElevationAlternative lightweight enclosureThis enclosure is a lightweight alternative to the patio structure and is intended to becovered with flexible netting that has a sewn in door. The structure will not support aroof and is unsuitable for other mesh cladding. This type of lightweight enclosure isonly suitable for situations where the cat has constant access to the owner’shouse through a cat door, so it can seek shelter during inclement weather.See Figure 10 illustration.The frame is made from round galvanised steel tubing that is bent at an angle, fixed to thewall at the top, and set in concrete pads in the ground at the other end. See Figure 7.To provide lateral support, the structure will need to be cross-braced or fixed tosomething solid, for example a fence.The recommended wall fitting is a metal flange that is threaded onto the pipe and fixedto the structure by means of coach bolts or masonry plugs. See Figure 4B.The other end of the pipe is set into a concrete footing. Bracing is attached with prefabpipefittings that are readily available from your supplier. See Figure 8.The structure can be covered with a prefabricated flexible netting cover with a sewn inzippered entrance (appendix 1 for details of a supplier of netting products ).Tools required– Shovel – Spirit level– Drill – Roofing square– Masonry or wood bits – Shifting spannerMaterials required– Galvanised pipe – Prefab pipe fitting (see Figure 8)– Screw on flanges – Flexible netting cover– Coach bolts or masonry plugs – Tie wire– Concrete pre-mixStep 1 – Basic Design and Pre-fabricationDraw the basic plan and discuss it with your steel supplier who can recommend theoptimum pipe diameter, usually around 50mm. Have the pipe cut to length and bentBased on your design identify pipes that need to be threaded on the top end to suitthe screw-on flanges for fixing and have them threaded at the time of purchase.Most suppliers have a delivery service for those hard to handle components.Step 2 – Set outStart construction with a string line parallel to the supporting wall at the outside perimeterand another 2 string lines at right angles to the wall marking each end. See Figure 2.Step 3 – Setting the frame postsDig the footings and erect the structure ensuring that it is well braced.Take a spirit level and with a good eye, sight all pipes from all angles to make surethat they are in alignment with each other and in alignment with the support structure.Take care with this stage, as a poorly aligned frame can look shoddy.Fit the bracing to square the frame and level the top bars by packing the bottom ofthe pipes with small rocks in the footing holes. When you are happy that everything isstraight and square, mix up a quantity of premix cement and pour the footings.Allow to set to specification.Set a wooden board into the ground all around the perimeter. The prefabricated nettingcover will be fastened to this board.Measure the finished project for the prefabricated netting.Step 4 – Fixing the nettingThe netting is tied to the frame with galvanised tie wire. It is fixed to wood and masonrywith battens, as for patio structure.
11Figu re 1 AFigu re 4 AFigu re 1 BFigu re 6Figu re 3Figu re 5Figu re 1 CFigure 9: Patio type sturucture. This shows the basic building structure prior to the addition ofsolid weatherproof wall cladding on parts of the enclosure (to provide the cat with shelter) andprior to the addition of other features (platforms, climbing planks, scratching posts, beds etc)as described in the text.Figure 4BAppendix 1:Netting products (note there may be other supplierswho provide suitable netting, in addition to thesupplier listed below) *Oxley NetsPO Box 128 Port Melbourne Victoria 320720 Network Drive, Port Melbourne, Victoria(03) 9646 3497, Toll free: 1800 816 505www.oxleynets.com.auFigure 8Figure 7*The content of this Department of Primary Industries (DPI) documentis provided for information purposes only. Information published byDPI is considered to be true and correct at the time of publication.DPI gives no representation or warranty as to the qualifications orsuitability of the service providers listed, nor any representation orwarranty that there are no other persons who provide services of thistype as the list is not intended to be exhaustive.Figure 1CFigure 10: Alternative lightweight enclosure
Page 1 and 2: How tobuildcatprooffencingcat enclo
Page 3: IntroductionContrary to popular bel
Page 6 and 7: Cat Proof FencingHave you considere
Page 8 and 9: Step 1 Measure and plan the project
Page 10 and 11: Cat enclosureattached to anexisting
Page 12 and 13: Material ChecklistFirstly, draw up
Page 16 and 17: Free standingcat enclosureCats love
Page 18 and 19: If however you do not have access t
Page 20 and 21: Step 4 - InstallationIf fixing on a
Page 22 and 23: THIS PUBLICATION ISFUNDED BY YOUR C

How to build a cat enclosure - City of Tea Tree Gully

Create successful ePaper yourself

Delete template?

Save as template?