Monsoon Universal Single Installation Guide - Taps4Less.com

More documents

Recommendations

Info

Pump Connections (General)22 mm copper inletpipework22 mm copper outletpipework.Integral pump isolating valveshown in ‘ON’ position.Suction supplyfrom tank withpush-in plumbingconnection.In the case of horizontal feeds use a22 mm compatible stem elbow (notsupplied). Do not bend the hosemore than 30° as they may becomedamaged, transmit noise or leak.22 mm flexiblepipes with push-inconnections, ensurethat connection isfully pushed homeinto hose end fitting and that hosesare kept as straight as possible.Isolating valve.Integral pump isolatingvalve shown in ‘OFF’position.Flexible hose.Flexible hose.30°Max.permittedflexiblehose bend.Suction supply from tankwith G ¾ male threadedpump connection.G ¾ running nut with captivesealing washer.Pressure switch.Inlet strainer housedin this location (seemaintenance section).Vent plug.G ¾ running nut withcaptive sealing washer.Delivery supply to shower/bathroomfitted with G ¾ male threaded pumpconnection.Flow switch.Pump body.Do not kink or twistthe hose.Anti-vibration foot.Fig. 11The pump should not be screwed down, ensure anti-vibration feet and flex hosesare used.Never operate pump with inlet and/or outlet isolating valves in the closedposition. Damage will occur!- 10 -
Typical Low Level InstallationIn certain installations it may be necessary to install a 90° bend on the inlet or outletconnections of the pump before the flexible hose to accommodate a low level installation.Below are some preferred connection options. All connections seal on the pump bodyusing a fibre or rubber sealing washer. Tap connector fittings should be used which mustbe of an appropriate pressure and temperature rating.It is essential when using any of the fittings shown below, that a correct water tight sealis obtained between the pump body and selected fitting and also the flexible hose andselected fitting. If in doubt contact the fitting manufacturer and confirm compatibility withthe connection to be sealed.Carefully check connections and pipework for leaks whilst pump running and stationarybefore leaving the installation unattended.G ¾ female x 22 mmelbow tap connector.22 mm copper pipe.22 mm compression toG ¾ male.G ¾ female flexible hose(supplied in kit).G ¾ female flexible hose(supplied in kit).22 mm to G¾male.G ¾ femaleflexible hose(supplied inkit).Fibre washer.22 mmelbow.22 mmcopperpipe22 mm compression toG ¾ male.22 mm stem elbow.Fig. 12G ¾ female x 22 mmtap connector.Fibre washer.G ¾ female x 22 mmswivel tap connectorwith rubber sealingwasher.STEP 5 ELECTRICAL INSTALLATIONWARNINGS:• The electrical installation must be carried out in accordance with thecurrent national electrical regulations and installed by a competentperson.• In the interests of electrical safety a 30 mA residual current device(R.C.D.) should be installed in the supply circuit. This may be part ofa consumer unit or a separate unit.• Before starting work on the electrical supply ensure power supply isisolated.• This appliance must be earthed.• The motor and wiring must not be exposed to water.• Do not allow the supply cord to contact hot surfaces, including themotor shell, pump body or pipework. The cord should be safelyrouted and secured by cable clips.- 11 -Sealing washer (sometimescaptured in fitting)G ¾ female x 22 mm tapconnector with rubbersealing washer.
Page 1 and 2: Installation InstructionsFor Monsoo
Page 3: STEP 2: PUMP LOCATIONWARNINGS:• P
Page 6: • Do not install a non-return val
Page 9: 2. Prior to inserting pipe into fit
Page 13 and 14: The wire which is coloured green an
Page 15 and 16: 3. PrimingWARNINGNever operate pump
Page 17 and 18: M4 screwsManifold clampInlet fittin
Page 19 and 20: TECHNICAL SPECIFICATIONPower supply
Page 21 and 22: Dry Run ProtectionThis pump is fitt
Page 23 and 24: If you do not have on-line access o

Monsoon Universal Single Installation Guide - Taps4Less.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?