9010 Intelek-Pro Flow Controller - Georg Fischer Signet LLC

More documents

Recommendations

Info

2.3 Input ConnectionsFour input sources are accepted:Note: See section 4.4for a listing of available inputcards.A. Non-isolated Frequency InputsFrequency (non-iso) card: Accepts non-isolated,0 to 10 kHz @ 0.2 Vp-p minimum sine or squarewave signal inputs. This card requires dip switchconfiguration prior to operation.B. Isolated Frequency InputsFrequency (iso) card: Accepts isolated, 0 to10 kHz @ 0.5 Vp-p minimum sine or square wavesignal inputs. No configuration required.C. Analog InputsTwo analog input cards are offered:• Analog (iso) current, 4 to 20/0 to 20 mA• Analog (iso) voltage, 0 to 5/0 to 10 VDCInput ranges are software selectable, requiring nointernal configuration.Figure 4Input WiringOUTPUTANL2SERIALA inSENSORSS CNT GND PLSR+ R-Tx GND RxA+ A- BLK RED SHLDTo reduce the possibility ofnoise interference, separateinput lines from AC powerlines.CA&B1 2 3 4 5 6 7 8 9 10 11 12 13 14R+Analog Input:Current or VoltageExternal DCPower SupplyORFrequency Input:for <strong>Signet</strong> sensorsand others+-R-+ -BLACKREDSHIELD+GF+SIGNET85126
2.4 Standard Output ConnectionsStandard OutputsAn open collector counter pulse output (CNT) anda sensor pulse output (PLS) are included with yourunit.The counter pulse output (synchronous w/totalizer)emits an open collector 150 ms pulse with amaximum current sinking capacity of 50 mA @30 VDC, and is ideal for driving an externalcounter or accumulator. An external DC powersupply and current limiting resistor are requiredfor operation.The sensor pulse output (PLS) emits a standard TTLfrequency output in phase with the sensor inputand can be used to drive +GF+ SIGNETinstruments (except +GF+ SIGNET 5090 and5091) and other TTL compatible devices.SSOUTPUTCNT GND PLSANL2R+ R-SERIALTx GND RxA in SENSORA+ A- BLK RED SHLDFigure 5Sensor pulse output (PLS)/counter output (CNT)wiring1 2 3 4 5 6 7 8 9 10 11 12 13 14ORRed (2)Shld (3)InputGnd+GF+ SIGNETIndicator or<strong>Controller</strong>TTLCompatibleDevice600Ω @ >1.5 WGnd+INGnd5 to 30 VDCPower SupplyExternal counteror accumulatorTo reduce the possibility ofnoise interference, separateoutput lines from AC powerlines.7
Page 1 and 2: +GF+ SIGNET 9010 Intelek-ProFlow Co
Page 3 and 4: ChapterPage1 Introduction 11.1 Intr
Page 5 and 6: 1.1 IntroductionYour new +GF+ SIGNE
Page 7 and 8: 1.3 Rear Panel Description1110 9 8
Page 9: 2.2 Power ConnectionsAC Power Conne
Page 13 and 14: 2.6 Verifying Analog OutputsInstall
Page 15 and 16: setpoint, hysteresis etc.The OUTPUT
Page 17 and 18: 188884mA ISYesModify?MODPress toent
Page 19 and 20: 3.4 2-Relay OperationsThe 2-Relay o
Page 21 and 22: 3.6 Calibration Menu, Analog Output
Page 23 and 24: 4.1 Accessing Internal Options1. Re
Page 25 and 26: 4.4 Option Cards and AccessoriesPar
Page 27 and 28: 4.6 Output Card ConfigurationEach 4
Page 29 and 30: Isolated freq input: 0.5 Vp-pIsolat
Page 31 and 32: Signet Scientific Company shall hav
Page 33 and 34: Notes:
Page 36: +GF+ SIGNETSales Offices:USA George

9010 Intelek-Pro Flow Controller - Georg Fischer Signet LLC

Create successful ePaper yourself

Delete template?

Save as template?