9010 Intelek-Pro Flow Controller - Georg Fischer Signet LLC

More documents

Recommendations

Info

3.5 Calibration Menu, 2-RelayNoAMODSecurityCode?YesUnlock securitycode using:ENTERRELAYLORLY1 ISModify?Yes Press to selectMOD relay operation modeLO, HIGH, or PULSEENTERNoRecall original valueMODRELAYYesSelectnextitem?NoNo PULSEMode?FLOW Normal operation YesGo toBNote: Displayed decimalposition set by CAL menuK-factorRELAY0100SET RLY1YesYesModify?NoSelectnextitem?MODPress toset relay setpointRecall original valueMODENTERNoFLOWNormal operation0020SET HYS1Modify?YesMODPressselect relayhysteresistoENTERExiting MenuMenu will repeat untilis pressed.FLOWRelay 2 LO, HIGH,or PULSE, go to:AYesNoSelectnextitem?NoRecall original valueFLOWNormal operationMODBRELAYNote: Relay cannot exceed4 pulses per second.rLY 1XXXXXXX.XModify?Yes Press to setMOD pulse units (0.1 to9999999.9)ENTERRelay 2 LO, HIGH,or PULSE, go to:ANoRecall original valueMOD16
3.6 Calibration Menu, Analog OutputsMODNoSecurityCode?YesUnlock securitycode using:ENTEROUTPUT4 to 20/0 to 20 mA (iso/non-iso) options illustrated9999ANL 1 4mModify?YesMODPress to selectflow rate at 4 mAoutput signalENTEROUTPUTYesNoSelectnextitem?Recall original valueMODNoFLOW Normal operation9999ANL 1 20mModify?YesMODPress to selectflow rate at 20 mAoutput signalENTEROUTPUTYesNoSelectnextitem?Recall original valueMODNoFLOWNormal operation4ADJUSTAmmeter required,see Figure 10OUTPUTYesYesModify?NoSelectnextitem?MODPress to fine tune4 mA output signal.See note*Recall original valueMODENTERFLOW*Note: Press: toquickly access the minimum ormaximum current output signalPress:to finetune the current output signalNoFLOW Normal operation20ADJUSTAmmeter required,see Figure 10OUTPUTYesYesModify? MODNoRepeatMenu?NoPress to fine tune20 mA output signal.See note*Recall original valueFLOW Normal operationMODENTERFigure 10The min. and max. currentadjustment steps require anexternal ammeter for monitoringthe current output.OUTPUTANL2SERIALA inSENSORSSCNT GND PLSR+ R-Tx GND RxA+ A- BLK RED SHLDExiting MenuMenu will repeat untilFLOWis pressed.1 2 3 4 5 6 7 8 9 10 11 12 13 14R+AMMETERR-R-R+15 16 17 18 19 20 21 22 23 24 25 26 27 28L1AC INN+ GND NO C NC NO C NC R+ R-DC IN RLY1 RLY2 ANL117
Page 1 and 2: +GF+ SIGNET 9010 Intelek-ProFlow Co
Page 3 and 4: ChapterPage1 Introduction 11.1 Intr
Page 5 and 6: 1.1 IntroductionYour new +GF+ SIGNE
Page 7 and 8: 1.3 Rear Panel Description1110 9 8
Page 9 and 10: 2.2 Power ConnectionsAC Power Conne
Page 11 and 12: 2.4 Standard Output ConnectionsStan
Page 13 and 14: 2.6 Verifying Analog OutputsInstall
Page 15 and 16: setpoint, hysteresis etc.The OUTPUT
Page 17 and 18: 188884mA ISYesModify?MODPress toent
Page 19: 3.4 2-Relay OperationsThe 2-Relay o
Page 23 and 24: 4.1 Accessing Internal Options1. Re
Page 25 and 26: 4.4 Option Cards and AccessoriesPar
Page 27 and 28: 4.6 Output Card ConfigurationEach 4
Page 29 and 30: Isolated freq input: 0.5 Vp-pIsolat
Page 31 and 32: Signet Scientific Company shall hav
Page 33 and 34: Notes:
Page 36: +GF+ SIGNETSales Offices:USA George

9010 Intelek-Pro Flow Controller - Georg Fischer Signet LLC

Create successful ePaper yourself

Delete template?

Save as template?