Fluke Networks TS45S ADSL Safe test set users guide - Datacomtools

More documents

Recommendations

Info

Replacing the Line CordA worn out or damaged line cord can be replaced by the user. To obtain areplacement line cord contact your local distributor or Harris Corporation atthe location given in the Warranty Section.WARNING:Read all instructions completely and understand possible hazards to enduser if not performed properly.WARNING:Disconnect test set clips from any metallic connections before performingthis maintenance.Removing theOld Line CordInstalling NewLine CordTo remove the old line cord:Notes: 1. Battery cover screws are retained in the cover and will not come all the way out.2. Be careful not to damage or pinch the speaker wires, printed circuit faces or insulating materials.3. Be sure to account for all hardware removed. Loose or missing hardware could create a hazard for theend user.1. Using a Phillips screwdriver, loosen only the four screws attaching the battery door cover to theback of the test set (see Figure 4).2. Remove the battery door cover (see Figure 5) and battery from the test set.3. Loosen the two screws that hold the line cord to the PCB (see Figure 8).4. Using needle nose pliers or one of the line cord clips, remove the two screws and washers fromthe line cord connectors.5. Remove the plastic clip (see Figure 9) that holds the line cord strain relief in place.6. Slip the line cord screw lugs (see Figure 10) through the hole in the end of the housing.To install a new line cord:1. From the outside of the housing, slide the screw lugs of a new line cord through the hole in the endof the test set housing. Make sure the crimp barrel offset side of the screw lugs is up (seeFigure 11) and that the line cord screw lugs are flush against the circuit board.2. Fasten the red wire lug to the PCB (Ring) with screw and washer (see Figure 10).3. Fasten the black wire lug to the PCB (Tip) with screw and washer (see Figure 10).4. Insert the plastic clip over the line cord strain relief at the base of the test set housing (seeFigure 9) and press tightly into place. Inspect all work to ensure no pinched wires or areas whereweather resistance and safe operation is affected.5. Reinstall the battery. Observe the proper polarity.Note: Do not over tighten screws. Over tightening will strip the plastic.6. Place the battery door cover (see Figure 5) on the test set and fasten the four screws (seeFigure 4). Tighten screws to a maximum torque of 0.904 N-m or 8 in-lb.TS45S Test Set 19
BLACK LINECORDRED LINECORDSCREW LUGNote: Speaker Not ShownFor Illustration Purposes.SCREW LUGts45s_003TS 45Rts45s_020Figure 8. Removal/Installation of Line CordScrewsFigure 10. Removal/Installation of Line CordScrew LugsCrimp barrelis offsetts4x_021Correct OrientationIncorrect orientationFigure 11. Orientation of Line Cord Screw LugsTS 45Rts45s_019Figure 9. Removal/Installation of the Plastic Clip20TS45S Test Set
Page 1 and 2: Network Support DivisionTS ® 45S A
Page 3 and 4: Contents■ Safety Information 1■
Page 5 and 6: IntroductionThe TS45S Test Set is a
Page 7 and 8: Controls and IndicatorsAudio Contro
Page 9 and 10: Table 3. Test Set Keypad Controls a
Page 11 and 12: Table 4. TS45S Model and Line Cord
Page 13 and 14: Answering a Call 1. If a ringing si
Page 15 and 16: When going from pair to pair search
Page 17 and 18: Configuring Your Test SetLast Numbe
Page 19 and 20: Speaker/HighVolume Timeout(Cont’d
Page 21: TS 45SMUTEDATARCLDATALNRRCLDATALNRP
Page 25 and 26: Return or Repair of EquipmentThe re
Page 27: Network Support Division | 809 Call

Fluke Networks TS45S ADSL Safe test set users guide - Datacomtools

Create successful ePaper yourself

Delete template?

Save as template?