1995 MAXIMA MIL LIGHT 'ON' CODES P0340, P1335 ... - Lyberty
1995 MAXIMA MIL LIGHT 'ON' CODES P0340, P1335 ... - Lyberty
1995 MAXIMA MIL LIGHT 'ON' CODES P0340, P1335 ... - Lyberty
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Classification: Reference: Date:EC95-008 NTB95-038 April 5, <strong>1995</strong><strong>1995</strong> <strong>MAXIMA</strong> <strong>MIL</strong> <strong>LIGHT</strong> <strong>'ON'</strong> <strong>CODES</strong> <strong>P0340</strong>, <strong>P1335</strong>,P1336, AND P0335APPLIED VEHICLE(S):<strong>1995</strong> Maxima (A32)SERVICE INFORMATIONIf a customer complains of <strong>MIL</strong> (Malfunction Indicator Lamp) <strong>'ON'</strong>, and a DTC (DiagnosticTrouble Code) of <strong>P0340</strong> (Camshaft Position Sensor [CMPS] [Phase]) or <strong>P1335</strong> (CrankPosition Sensor-Ref) or P1336 (Crankshaft Position Sensor POS-cog) or P0335(Crankshaft Position Sensor [POS]) is found stored, use the following procedure to repairthe vehicle.SERVICE PROCEDURE1. If a customer complains of <strong>MIL</strong> (Malfunction Indicator Lamp) <strong>'ON'</strong>, and a DTC(Diagnostic Trouble Code) of <strong>P0340</strong> (Camshaft Position Sensor [CMPS] [Phase]) or<strong>P1335</strong> (Crank Position Sensor-Ref) or P1336 (Crankshaft Position Sensor POS-cog) orP0335 (Crankshaft Position Sensor [POS]) is found stored, use the following procedureto repair the vehicle.2. Check the continuity of all wires in the circuit diagram for the indicated sensor. Alsocheck to ensure no short circuits to ground are present.3. If steps 1 & 2 do not resolve the incident, open the ECM end of the ECCS harness forapproximately 30 cm (12 inches). Find and separate the five (5) white wires from thesix (6) fuel injector wires. These two groups of wires should be separated from eachother the entire distance from the ECM connector (F101) to the shield portions of thewhite wires (approximately 30 cm [12 inches]).DTC CODE ECM Pin # Wire Color Injector # WIRE Pin # Wire Color<strong>P0340</strong> 46, 47 White 1 102 R/B<strong>P1335</strong> 44, 48 White 2 109 R/GP1336 49 White 3 104 R/YP0335 49 White 4 111 B/OR5 106 L/W6 113 PU/R1/3
4. Retape the harness together keeping the two groups of wires separated from eachother by at least 1 cm (0.4 inch) from the ECM connector up to where the shield beginsfor the white wire(s).5. If the incident is not resolved using the above procedure, check Service-Comm forupdated information or contact the Nissan TECH LINE for further assistance.2/3
CLAIMS INFORMATIONOPERATION OP CODE PNC SYMPTOM DIAGNOSIS FRTRepair Wiring Harness* RA16AA * * HD 61 or 62 S/T hrs* "Straight Time" operation-claim actual hours. Do not claim this operation with any otherOp Code(s).* * Reference the "RA" section of the current "Warranty Flat Rate Manual" and select theappropriate wiring harness PNC from the "Failed Part" Listing.NOTE: "New Claims System" dealers should use the P/N of the appropriate wiring harnessfor the primary failed part.3/3
Change language