01V96 V2 Editor Manual - Yamaha Commercial Audio

More documents

Recommendations

Info

Other Functions ❏ ❏ ❏ Copy & Paste Function You can copy and paste the channel parameters. In the Console Setup window (page 3), you can also specify the parameters to be copied. The following table describes how to use the Copy & Paste function. Copying a channel Right-click (+click) a copy source channel, then choose [Copy]. Pasting a channel Resetting to the default value (Ctrl ( ) + click) Move the cursor to a control or a parameter value, then hold down the key ( ) and click the mouse button to reset the value to the default (e.g., to reset an Input Channel fader to – ∞, or reset a pan setting to Center). Ctrl( )+Shift+Click Right-click (+click) the copy destination channel, then choose [Paste]. Move the cursor to a fader or AUX Send control, then hold down the key ([ ]) and key and click the mouse button to reset the value to the nominal level. 01V96 Editor—Owner’s Manual 6 Getting Started Using Windows 01V96 Editor Windows Keyboard Shortcuts Index
Using 01V96 Editor Windows Master Window 1 2 3 4 5 6 7 8 9 The Master window enables you to switch between layers and control Stereo Out signals. To open this window, choose [Master] from the [Windows] menu. A [ONLINE]/[OFFLINE] button Repeatedly clicking this button toggles between online and offline status. Note: If 01V96 Editor is not connected or is not communicating with the 01V96, clicking this button will not switch the unit from offline to online. This indicator is displayed when 01V96 Editor is connected to the 01V96 correctly. If the connection is correct, the 01V96 Editor parameters will work in unison with the 01V96 parameters. This indicator is displayed when 01V96 Editor is not connected or is not communicating with the 01V96, or when you have selected Offline Edit. If the connection is incomplete, the 01V96 Editor parameters will not work in unison with the 01V96 parameters. B Meters These meters display the output level of the Stereo Out when Surround mode is set to “STEREO,” or the Bus Outs used for surround processing when Surround mode is set to 3-1, 5.1 or 6.1. The meters in 3-1, 5.1 and 6.1 Surround modes are shown on the right. C LAYER buttons These buttons are used to select the Layers. D PAN CONTROL These buttons are used to select either “STEREO” (Stereo display mode) or “SURR” (Surround display mode). The 3-1 5.1 6.1 Pan control on the Input Channels is a rotary control when “STEREO” is selected, and a dot on a pan graph when “SURR” is selected. If Surround mode is set to Stereo, the [SURR] button will be disabled. E Scene number display This display indicates the currently-recalled scene’s number. F [SELECT] button This button is used to select the Stereo Out. G [ON] button This button turns the Stereo Out on and off. It appears orange while the Stereo Out is on. H Master fader This is the Stereo Out fader. I Fader value indicator This indicator indicates the fader position in decibels (dB). 01V96 Editor—Owner’s Manual 7 Getting Started Windows Keyboard Shortcuts Index
Page 1 and 2: Special Notices • The software an
Page 3 and 4: ❏ Channel Select: These options d
Page 5: If you save a Session in an Editor,
Page 9 and 10: P Q T R S V W X Y Z a P Delay param
Page 11 and 12: M SOLO button This button solos the
Page 13 and 14: ❏ Remote Channels A B C D E F Whe
Page 15 and 16: C EQUALIZER section This section co
Page 17 and 18: F FADER GROUP & MUTE GROUP section
Page 19 and 20: F COMPRESSOR section This section c
Page 21 and 22: Library Window The Library window e
Page 23 and 24: Patch Editor Window The Patch Edito
Page 25 and 26: ❏ INSERT PATCH Page A B C E F A C
Page 27 and 28: ❏ DIRECT OUT PATCH Page A B C A C
Page 29 and 30: Effect Editor Window The Effect Edi
Page 31 and 32: Meter Window The Meter window displ
Page 33 and 34: Index Numerics 1-16 button ........

01V96 V2 Editor Manual - Yamaha Commercial Audio

Create successful ePaper yourself

Delete template?

Save as template?