Fybroc Division series 1500 horizontal pumps - MHz Electronics, Inc

More documents

Recommendations

Info

INDEXPagePageFybroc Warranty 3 Assembly/Disassembly Procedures 10Installation Instructions 4 General 10Location 4 Disassembly 10Foundation 4 Power-frame Disassembly 11Initial Alignment 4 Power-frame Assembly 12Piping the Pump 5 Pump End Assembly 13Suction Piping 5 John Crane Type 8B2 13Discharge Piping 5 John Crane Type 8-1T 14Ancillary Piping 5 John Crane Type 8-D 14Electrical Connections 6 Packed Stuffing Box 15Rotation 6 Impeller Adjustment 16Alignment and Coupling Installation 6 Installation Instructions Wood’s Couplings 17Start-up and Operating Procedures 7 Operational Start-up Checklist 19Lubrication 7 Sectional Drawings 20Oil Bath Lubrication 7 1500 Group I 20Re-Greasable Bearings 7 1500 Group II 21Greased for Life Bearings 7 1500 Group III 22Seal Flushing 7 Typical Mechanical Seal Installations 23Mechanical Seals 7 Product Flush 23Packed Stuffing Box 7 External Flush 24Priming 7 Mechanical Seal Piping/Flow Requirements 25Starting 7 Single Mechanical Seal 25Operational Check List 8 Double Mechanical Seal 26Maintenance 8 Notes 27Pump 8 Notes 28Oil Bath Lubrication 8 Notes 29Re-Greasable Bearings 8Greased for Life Bearings 8Motor 8Trouble Check List 9ORDERING REPLACEMENT PARTSFor future reference fill in the following information from the pump nameplate.This will be necessary to ensure accuracy when ordering replacement parts.ModelSizeSerial NumberImpeller Diameter InstalledSeal TypeMaterial of Construction
Fybroc DivisionWARRANTYPERFORMANCEGUARANTEEACCEPTANCETESTSPERFORMANCEPRESENTATIONSFIELD TESTINGALL WARRANTIESFYBROC pumps are warranted by the Company, insofar as the same are of its own manufacture,against defects in materials and workmanship under proper and normal use andservice, for a period of one year from the date of original shipment from the factory.FYBROC’s obligation is limited, however, to furnishing without charge, F.O.B. its factory,new parts to replace any similar parts of its own manufacture so proving defective withinsaid period, provided the Buyer has given FYBROC immediate written notice upon discoveryof such defect. No allowance will be made for labor charges. FYBROC shall have theoption of requiring the return of the defective material, transportation prepaid, to establishthe claim.FYBROC makes no warranty or guarantee whatsoever, either express or implied, of primemover, starting equipment, electrical apparatus, parts or material not manufactured byFybroc, except to the extent that warranty is made by the manufacturer of such equipmentand material.FYBROC assumes no liability for damages or delays caused by defective material, and noallowance will be made for local repair bills or expenses without the prior written approvalor authority of FYBROC.Under no circumstances will FYBROC be liable for indirect, special or consequential loss ordamage of any kind and the Buyer assumes all liability for the consequences of its use ormisuse by the by the Buyer, his employees, or others.Is at the specified point of rating only and will not cover performance under conditions varyingtherefrom, nor for sustained performance over any period of time.If required, shall be conducted in accordance with the practices as set forth in the HydraulicInstitute Standards. The expense of any such tests shall be borne by the buyer.Are based on shop laboratory tests with cold water as outlined in the Hydraulic InstituteStandards.Due to the inaccuracies of field testing, the results of any such tests conducted by or forthe Buyer shall be interpreted as being only indicative of the actual field performance of thepump. No equipment will be furnished on the basis of acceptance by results of field tests.If the buyer, after such a test, questions the performance of the pump, he may at his optionrequest a test to establish the performance. Such tests will be conducted in accordancewith the above paragraph entitled “Acceptance Tests.”Are void if -a. Pipe strains are the cause of damage.b. Pump handles liquids other than those specified in detail.c. NPSH lower than required by pump impeller.d. Operating speed is higher than specified.e. Improper field installation.To combat corrosion, abrasion, erosion, or pumping solids, foreign objects, or pumpingliquids at elevated temperature, any such recommendations will be based on the bestavailable experience of FYBROC and the supplier of the material and industry, BUT WILLNOT CONSTITUTE A GUARANTEE AGAINST THESE EFFECTS.RECOMMENDATIONSFOR SPECIALMATERIALSThe foregoing warranty is made in lieu of all other warranties guarantees, obligations orliabilities, expressed or implied, by FYBROC or its representatives. All statutory or impliedwarranties, other than of title, are hereby expressly negated and excluded.All illustrations and provisions in specifications are descriptive and are not intended aswarranties. Penalty of any kind are not acceptable unless approved in writing by an officerof Met-Pro Corporation.3
Page 1: Fybroc Divisionseries 1500 horizont
Page 5 and 6: PIPING THE PUMPPiping must not be c
Page 7 and 8: LUBRICATIONOil Bath LubricationWhen
Page 9: Instructions For Lubricating Motors
Page 12 and 13: POWER-FRAME ASSEMBLY1) Clean and vi
Page 14 and 15: clearance, adjust the shaft forward
Page 16 and 17: IMPELLER ADJUSTMENTThe horizontal 1
Page 18 and 19: MAXIMUM ALLOWABLE MISALIGNMENTSleev
Page 20 and 21: 1500 SERIES GROUP 120
Page 22 and 23: 1500 SERIES GROUP 322
Page 24 and 25: 1500 SERIES SEAL AND STUFFING BOX A
Page 26 and 27: FLUSH PIPING FOR DOUBLE INSIDE MECH
Page 28 and 29: NOTES28
Page 30: ©COPYRIGHT 2000 MET-PRO CORPORATIO

Fybroc Division series 1500 horizontal pumps - MHz Electronics, Inc

Create successful ePaper yourself

Delete template?

Save as template?