FA-M3 Hardware Manual - Yokogawa

More documents

Recommendations

Info

A1.3 Peripheral Tools Supporting the ProgramDevelopment of the FA-M3You can conveniently create and debug your programs on your personal computer.A1-10- FA-M3 Programming Tool WideField3- FA-M3 ToolBox- BASIC Programming Tool M3 for WindowsFA-M3CD-ROMPersonalcomputerEthernet, cable for programming tools (RS-232-C),USB or FL-netA1.Figure A1.5 Support Tools for the FA-M3PrinterFA010301.VSDIM 34M06C11-01E 23nd Edition : Oct. 01, 2013-00
A2. Specifications and ConfigurationA2.1 Specifications• Common SpecificationsEnvironmentStructure & AppearanceA2-1ItemSpecificationsSurrounding air temperature rangeOperating : 0 to 55°C *1Storage : -20°C to 75°CSurrounding humidity rangeOperating : 10 to 90% RH (non-condensing)Storage : 10 to 90% RH (non-condensing)Surrounding atmosphereMust be free of corrosive gases, flammable gases or heavy dust.GroundingAC Power supply module : Protective earth (Comply with the regulation of each country.)DC Power supply module : Functional earthTested using a noise simulator with a noise voltage of 1500 Vp-p, pulse width of 1 µs, rise time of 1 ns,Noise immunityand repetition frequency of 25 to 60 Hz.For CE Marking-compliant modules, compliant to EN61326-1, EN61326-2-3 *6 and EN61000-6-2Tested in compliance with JIS C0040 under the following conditions:Vibration resistance- Frequency ranges: 10 to 57 Hz with an amplitude of 0.075 mm57 to 150 Hz with an acceleration of 9.8 m/s 2 (1 G)- Direction and sweep cycles: 10 times each in the X, Y, and Z directionsTested in compliance with JIS C0041 under the following conditions:Shock resistance- Direction and sweep cycles: 3 times each in the X, Y, and Z directions with an acceleration of 147 m/s 2(98 m/s 2 with DIN-rail mounting)StructureDesigned for mounting inside a panel enclosureAltitude of installationMax. of 2000 m above sea levelULUL508 approved, File No.E188707(Overvoltage Category *3 II, Pollution Degree *4 2)EN 61326-1 Class A, Table 2 (For use in industrial locations)ComplianceEMC Directive *7 EN 61326-2-3 *6, EN 55011 Class A, Group 1with safety and CEEN 61000-6-2, EN 61000-3-2, EN 61000-3-3 complianceEMCLow Voltage EN 61010-1 compliance (Overvoltage Category *3 II, Pollution Degree *4 2)standards *2DirectiveEN 61010-2-030 compliance (Measurement Category O *8 )C-Tick EMC FrameworkEN 55011 Class A, Group 1 complianceEN 61326-1 Class A, Table 2 (For use in industrial locations) complianceKC EMC Regulations Korea Electromagnetic Conformity Standard (한국 전자파적합성기준) complianceCooling methodNatural-air cooledMountingDirect mounting with M4-size setscrews *5 or DIN-rail mounting (except for F3BU16-0N module)Finish colorLight cobalt blue, equivalent to Munsell 6.2PB 4.6/8.8;Lampblack, equivalent to Munsell 0.8Y 2.5/0.4External dimensionsSee the dimensional figures in Section A2.10, “External Dimensions.”*1: Some FA-M3 modules may have a narrower surrounding temperature range than 0-55°C. A system incorporating suchmodules must be used within the narrower surrounding temperature range for such modules.*2: For details on conforming modules, see “UL-approved, CE marking, C-Tick mark and KC mark - compliant Modules”(GS 34M06C11-21E) general specification brochure.*3: The term Overvoltage Category involves prescriptions on resistance to surge voltage reduction due to lightning and has fourcategories. Overvoltage Category II applies to systems with a rated voltage of 220/230/240 V and applies to electricalappliances, portable devices, etc.*4: The term Pollution Degree represents the degree of pollution with foreign matter, solid, liquid or gaseous, that may produce areduction of dielectric strength or surface resistivity in the operating environment of the equipment. Pollution degree 2 refers toan environment where normally only non-conductive pollution occurs but occasionally temporary conductivity caused bycondensation is to be expected.*5: For details on the number of mounting screws, see subsection A3.2.2.*6: EN61326-2-3 is applicable only to F3CU04-0S and F3CU04-1S.*7: This product is classified as Class A for use in industrial environments.If used in a residential environment, it may causeelectromagnetic interference (EMI). In such situations, it is the user's responsibility to adopt the necessary measuresagainst EMI.*8: EN 61010-2-030 is applicable only to modules with analog input terminal.Don’t use analog input terminals of the FA-M3 for measurement on Mains Circuit, since it has no measurement category.IM 34M06C11-01E 23nd Edition : Oct. 01, 2013-00
Page 1 and 2: User’sManualHardware ManualIM 34M
Page 4 and 5: iiImportant• About This Manual- T
Page 6 and 7: - Yokogawa Electric assumes no liab
Page 8 and 9: vi• Configure for CE Marking Conf
Page 10 and 11: viii• Waste Electrical and Electr
Page 12 and 13: xCopyrights and Trademarks• Copyr
Page 14: TOC-2A2.5 I/O Modules .............
Page 18 and 19: Blank Page
Page 20 and 21: Blank Page
Page 22 and 23: A1-2• Slot NumberA slot number id
Page 24 and 25: A1-4TIP■ Example of increasing th
Page 26: A1-6A1.2.2Restrictions on CPU Modul
Page 29: A1-9A1.2.4Restrictions due to Curre
Page 33 and 34: A2.2 FA-M3 Controller Configuration
Page 35 and 36: A2-5• ROM PacksModule Description
Page 37 and 38: A2-7• Analog I/O and Temperature
Page 39 and 40: • Counter and Positioning Modules
Page 41 and 42: For detailed cable specifications,
Page 43 and 44: A2.3 Power Supply ModulesA2-13(1) F
Page 45 and 46: A2-15(2) F3PU30-0N/F3PU30-0S Power
Page 47 and 48: A2-17(3) F3PU16-0N and F3PU26-0N Po
Page 49 and 50: A2-19(4) F3PU36-0N/F3PU36-0S Power
Page 51 and 52: A2.4 Base ModulesA2-21There are six
Page 53 and 54: A2-23• Isolation MethodsThe inter
Page 55 and 56: A2-25• Setting up the Pulse-captu
Page 57 and 58: A2-27(4) Functional Description- Pu
Page 59 and 60: A2-29(2) F3XA08-1N/F3XA08-2N AC Inp
Page 61 and 62: A2-31(3) F3XA16-1N AC Input ModuleI
Page 63 and 64: A2-33(5) F3XC08-0C No-voltage Conta
Page 65 and 66: A2-35(7) F3XD16-3F/F3XD16-4F/F3XD16
Page 67 and 68: A2-37(8) F3XD32-3F/F3XD32-4F/F3XD32
Page 69 and 70: A2-39(9) F3XD64-3F/F3XD64-4F DC Inp
Page 71 and 72: A2-41(10) F3XD08-6N DC Input Module
Page 73 and 74: A2-43(11) F3XD16-3N/F3XD16-4N DC-In
Page 75 and 76: A2-45(12) F3XD32-3N/F3XD32-4N/F3XD3
Page 77 and 78: A2-47(13) F3XD64-3N/F3XD64-4N DC In
Page 79 and 80: A2-49(14) F3XD64-6M DC Input Module
Page 81 and 82:
A2-51(16) F3YA08-2N Triac Output Mo
Page 83 and 84:
A2-53(17) F3YC08-0C/F3YC08-0N Relay
Page 85 and 86:
A2-55• Front View• Internal Cir
Page 89 and 90:
A2-59• Front ViewF3YD08-7A● Int
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
A2-67• Front View● Internal Cir
Page 99 and 100:
A2-69IM 34M06C11-01E 23th Edition :
Page 101 and 102:
A2-71CAUTIONOperation of the protec
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Page 113 and 114:
A2-83*3: If an inductive load, such
Page 115 and 116:
Page 117 and 118:
A2-87• Output BlockOutput typeIte
Page 119 and 120:
Page 121 and 122:
A2-91• Output BlockOutput typeIte
Page 123 and 124:
Page 125 and 126:
A2-95• Maximum Writing Operations
Page 127 and 128:
A2-97• KM13-1S (USB-serial Conver
Page 129 and 130:
(3) Cables for Connector Terminal B
Page 131 and 132:
(5) Fiber-optic CablesA2-101KM61, K
Page 133 and 134:
A2-103CAUTIONHandle the fiber-optic
Page 135 and 136:
(7) Monitor Cables (for F3SP66-4S a
Page 137 and 138:
A2-107A2.8 Terminal Block Unit and
Page 139 and 140:
A2-109• External DimensionsUnit:
Page 141 and 142:
A2-111•Operating Environment Spec
Page 143 and 144:
A2-113(3) TA60-0NThe TA60-0N connec
Page 145 and 146:
A2.9 Module Current Consumption Tab
Page 147 and 148:
A2-117I/O moduleModule DescriptionM
Page 149 and 150:
A2-119A2.10 External Power SupplyUs
Page 151 and 152:
F3PU01, F3PU10, F3PU16• Power Sup
Page 153 and 154:
A2-123Unit: mmF3XD32F3XD64-3N, F3XD
Page 155 and 156:
A3-1A3. Installation and WiringA3.1
Page 157 and 158:
A3.2 Methods for Mounting the FA-M3
Page 159 and 160:
A3-5A3.2.3Mounting on and Removing
Page 161 and 162:
A3-7• Removing the Rail Mount Kit
Page 163 and 164:
A3-9• Attaching the Module in Int
Page 165 and 166:
A3-11- In the case of Positioning m
Page 167 and 168:
A3-13A3.3.2Grounding LinesWhen cons
Page 169 and 170:
A3-15A3.3.5InterlockingAn interlock
Page 171 and 172:
• Standard Mode (common to all po
Page 173 and 174:
A3-19• Immediate Detection Mode(w
Page 175 and 176:
A3-21• Protecting Special Modules
Page 177 and 178:
A3-23A3.5.3Power Supply Wiring• A
Page 179 and 180:
A3-25A3.5.4Grounding ProcedurePU 10
Page 181 and 182:
A3.6.3Terminal Blocks and Connector
Page 183 and 184:
A3-29A3.6.4Connecting Input Devices
Page 185 and 186:
A3-31(4) Leakage Current Considerat
Page 187 and 188:
A3-33• Inrush Current Countermeas
Page 189 and 190:
A3.8 Calculating Power ConsumptionA
Page 191 and 192:
A3-37A3.9.1EMC Directive(1) Require
Page 193 and 194:
A3-39WARNINGThis product is classif
Page 195 and 196:
A3-41Short the FG and LG terminalso
Page 197 and 198:
TIPAdopt the following corrective a
Page 199 and 200:
A3.9.2Low Voltage DirectiveA3-45(1)
Page 201 and 202:
A3-47Pollution degree 4:The polluti
Page 203 and 204:
A4-1A4. Test Runs and Troubleshooti
Page 205 and 206:
A4-3A4.3 Self-diagnostic FunctionsA
Page 207 and 208:
A4-5A4.3.2Fault IdentificationThe F
Page 209 and 210:
PA4-7SeverityLevelMajorModerateMino
Page 211 and 212:
A4.4 Troubleshooting ProcedureIf an
Page 213 and 214:
A4-11(2) For the F3SP22, F3SP28, F3
Page 215 and 216:
A5-1A5. Maintenance and InspectionA
Page 217 and 218:
Appx. A1-1Appendix A1 System-wide R
Page 219 and 220:
Appx. A1-3Appendix Table A1.2 Numbe
Page 221 and 222:
Appendix A1.2Appx. A1-5Restrictions
Page 223 and 224:
Appx. A1-7Example:If the system is
Page 225 and 226:
Appendix A1.4.2For BASIC CPU Module
Page 227 and 228:
TOC B-1FA-M3Hardware ManualPart B F
Page 229 and 230:
B1-1B1. System ConfigurationB1.1 Sy
Page 231 and 232:
B1.2 Restrictions on Module Install
Page 233 and 234:
B2. Specifications and Configuratio
Page 235 and 236:
B2.3 Sequence CPU ModuleB2.3.1 Over
Page 237 and 238:
B2-5DANGERTo avoid electrical shock
Page 239 and 240:
FA-M3Hardware ManualPart C FA-M3 Va
Page 241 and 242:
C1. System ConfigurationC1.1 System
Page 243 and 244:
C1.2 Restrictions on Module Install
Page 245 and 246:
C2. Specifications and Configuratio
Page 247 and 248:
C2.3 Sequence CPU ModuleC2.3.1 Over
Page 249 and 250:
C2-5CAUTIONLG terminal has a half p
Page 251 and 252:
C2-7• Output BlockOutput typeItem
Page 253 and 254:
C2-9• Operating EnvironmentThis m
Page 255 and 256:
Index-1FA-M3Hardware ManualIM 34M06
Page 257 and 258:
Revision InformationiDocument Name:
show all

FA-M3 Hardware Manual - Yokogawa

Create successful ePaper yourself

Delete template?

Save as template?