3A2308A - Protective Coating Hand-Held Paint Sprayer, Operation ...

More documents

Recommendations

Info

OperationUnclogging Spray Tip/GuardAssembly5. Disengage trigger lock, put prime/pressure reliefvalve DOWN to spray position, and resume spraying.Always perform the Pressure Relief Procedure(page 9) before unclogging spray tip.1. To unclog tip obstruction, engage trigger lock andput prime/pressure relief valve UP to relieve pressure.ti19374ati19346a6. If tip is still clogged, it may be necessary to repeatsteps 1 - 5 and rotate the tip from SPRAY toUNCLOG several times. Repeat step 1 to releasepressure, remove and clean filter, or replace withnew tip assembly.ti19347ati19350a2. Reverse spray tip to UNCLOG position.ti19349ati19370a7. When obstruction is cleared, engage trigger lockand rotate arrow-shaped handle back to SPRAYposition.3. Aim sprayer at waste area, disengage trigger lock,and put prime/pressure relief valve DOWN to sprayposition. Pull trigger to clear clog.ti19350ati19371ati19374ati19346a4. Engage trigger lock. Put prime/pressure relief valveUP to relieve pressure and rotate spray tip back toSPRAY position.ti19347ati19350ati19371a18 3A2308A
OperationShutdown and Cleaning3. Remove cup from sprayer.NOTICEFailure to properly clean sprayer after each use willresult in hardened materials, damage to the sprayer, andthe warranty will no longer be valid. Do not store solventsother than mineral spirits in sprayer.Flushing Sprayerti19360a4. Remove lid from cup.Do not spray solvents through the spray tip. Clean the tipin a bucket of compatible solvent.Keep spray area well-ventilated. Keep a good supply offresh air moving through the area.NOTICEProtect the internal parts of this sprayer from water.Do not submerge the sprayer in cleaning fluid. Openingsin shroud allow cooling of mechanical parts and electronicsinside. If water or cleaning fluid gets into these openings,the sprayer could malfunction or becomepermanently damaged.ti19363a5. Remove material liner and lid from cup and properlydispose. Properly dispose any excess material leftin the liner.1. Engage trigger lock and put prime/pressure reliefvalve UP to release pressure.ti15000ati19350ati14994ati19347ati19352a2. Turn pressure control knob to prime/clean position.6. Insert a new liner into cup and fill 1/2 full with appropriateflushing fluid. Screw on lid and attach cup tosprayer. Shake sprayer to move flushing fluidaround and clean all wetted areas inside cup.ti19357ati19365a3A2308A 19
Page 1 and 2: Operation - Parts - RepairProtectiv
Page 3 and 4: WarningsWarningsThe following warni
Page 5 and 6: WarningsWARNINGCHARGER ELECTRIC SHO
Page 7 and 8: OperationOperationCharging the Batt
Page 9 and 10: OperationCommon ProceduresTrigger L
Page 11 and 12: Operation5. If yellow light is flas
Page 13 and 14: Operation8. Engage trigger lock and
Page 15 and 16: OperationPriming Pump1. Put prime/p
Page 17: OperationGetting Started with Basic
Page 21 and 22: OperationCleaning Sprayer ExteriorW
Page 23 and 24: PartsParts ListRef. Part Descriptio
Page 25 and 26: TroubleshootingProblem Cause Soluti
Page 27 and 28: TroubleshootingProblem Cause Soluti
Page 29 and 30: RepairOutlet Valve5. Clean as much
Page 31 and 32: RepairPump Module/Drive Module5. Re
Page 33 and 34: RepairClamshell6. Remove nut from g
Page 35 and 36: RepairMotor/Control Board Replaceme
Page 37 and 38: RepairSwitch Assembly5. Remove eigh
Page 39 and 40: RepairGear Replacement4. Remove fou
Page 41 and 42: Technical DataTechnical DataModels

3A2308A - Protective Coating Hand-Held Paint Sprayer, Operation ...

Create successful ePaper yourself

Delete template?

Save as template?