3A2308A - Protective Coating Hand-Held Paint Sprayer, Operation ...

More documents

Recommendations

Info

Repair3. Set motor housing into right half of clamshell andloosely install two bolts (42) to motor housing asshown below.7. Press ground stud into left half of clamshell. Tightennut onto stud. Install ground terminal to stud andtighten second nut onto stud. Install wire up alonghandle.42ti19629a4. Route wires from motor down the handle.ti19633a8. Insert static wick into right half of clamshell andinstall left clamshell to right clamshell.ti19630a5. Install trigger over top of wires. Route trigger wiresbehind trigger.ti19634aNOTICEWires can become damaged when pinched betweenclamshell halves. Make sure no wires are pinchedduring reassembly.ti19631a6. Insert trigger lock over trigger with o-ring facing out.9. Install bolts (42) to motor housing and install screws(43) to connect clamshell halves. Make sure LEDlights and static wick are securely in place. Tightenbolts (42) to 50 in-lb (5.6 N•m) and screws (43)to 9 in-lb (1 N•m).4342ti19632ati19635a10. Install pump module to drive module. See PumpModule/Drive Module, page 31.34 <strong>3A2308A</strong>
RepairMotor/Control Board Replacement Kit6. Unscrew nut from ground stud and remove ringterminal. Leave other nut secured to ground stud.Removal1. Engage trigger lock and put prime/pressure reliefvalve in UP position to relieve pressure.ti19640ati19350a2. Remove material cup and battery.ti19347a7. Remove motor, motor housing, switch, controlboard, indicator lights, trigger lock, and static wickfrom clamshell.ti19360a3. Remove pump module from drive module. SeePump Module/Drive Module, page 31.4. Remove four bolts (42) from motor housing.ti19617aInstallationti19639a1. Insert control board into right half of clamshell.425. Remove screws (43) from clamshell.43ti19636ati19627a2. Install two LED lights into designated slot in righthalf of clamshell. Push wire bundle into slots inclamshell.ti19637ati19628a<strong>3A2308A</strong> 35
Page 1 and 2: Operation - Parts - RepairProtectiv
Page 3 and 4: WarningsWarningsThe following warni
Page 5 and 6: WarningsWARNINGCHARGER ELECTRIC SHO
Page 7 and 8: OperationOperationCharging the Batt
Page 9 and 10: OperationCommon ProceduresTrigger L
Page 11 and 12: Operation5. If yellow light is flas
Page 13 and 14: Operation8. Engage trigger lock and
Page 15 and 16: OperationPriming Pump1. Put prime/p
Page 17 and 18: OperationGetting Started with Basic
Page 19 and 20: OperationShutdown and Cleaning3. Re
Page 21 and 22: OperationCleaning Sprayer ExteriorW
Page 23 and 24: PartsParts ListRef. Part Descriptio
Page 25 and 26: TroubleshootingProblem Cause Soluti
Page 27 and 28: TroubleshootingProblem Cause Soluti
Page 29 and 30: RepairOutlet Valve5. Clean as much
Page 31 and 32: RepairPump Module/Drive Module5. Re
Page 33: RepairClamshell6. Remove nut from g
Page 37 and 38: RepairSwitch Assembly5. Remove eigh
Page 39 and 40: RepairGear Replacement4. Remove fou
Page 41 and 42: Technical DataTechnical DataModels

3A2308A - Protective Coating Hand-Held Paint Sprayer, Operation ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?