3A2308A - Protective Coating Hand-Held Paint Sprayer, Operation ...

More documents

Recommendations

Info

RepairPressure Control KnobRemoval1. Engage trigger lock and put prime/pressure reliefvalve in UP position to relieve pressure.InstallationNOTE: Inlet valve must be fully installed before outletvalve can be installed.1. Make sure prime/pressure relief valve is in UP position.Use a thin screwdriver or allen wrench to turnoutlet valve counter-clockwise until it touches inletball. DO NOT TIGHTEN. Outlet valve should onlybe threaded until inlet ball does not move whentouched.ti19350ati19347a2. Loosen two set screws (34) from pressure controlknob and remove knob.ti19347a34ti19616ati19620a2. Install pressure control knob. Turn knob fully counter-clockwise(“0” setting will line up with red dot).Torque set screws (34) to 40 in-lb (4.5 N•m).34ti19620ati19351a30 <strong>3A2308A</strong>
RepairPump Module/Drive Module5. Remove pump module (35) from drive module (11).Removal35111. Engage trigger lock and put prime/pressure reliefvalve in UP position to relieve pressure.ti19625ati19350ati19347aInstallation1. Engage trigger lock and remove battery from unit.2. Remove material cup and battery.ti19350ati19617ati19360ati19617a3. Unscrew swivel bolt (22) by pressing down andturning it counter-clockwise. Use tool if needed.2. Assemble pump module (35) to drive module (11).Gears must properly engage for assembly. Slightlyrotate pump assembly as needed for properengagement.351122ti19624ati19621a4. Unscrew bolt (20). Use tool if needed.3. Assemble swivel bolt (22) and bolt (20). Partiallythread both bolts before tightening either bolt. Usetool to tighten and make sure bolts are secure.NOTE: Make sure there is no gap between the twohousings when assembling bolts.2220ti19618ati19622a20<strong>3A2308A</strong> 31
Page 1 and 2: Operation - Parts - RepairProtectiv
Page 3 and 4: WarningsWarningsThe following warni
Page 5 and 6: WarningsWARNINGCHARGER ELECTRIC SHO
Page 7 and 8: OperationOperationCharging the Batt
Page 9 and 10: OperationCommon ProceduresTrigger L
Page 11 and 12: Operation5. If yellow light is flas
Page 13 and 14: Operation8. Engage trigger lock and
Page 15 and 16: OperationPriming Pump1. Put prime/p
Page 17 and 18: OperationGetting Started with Basic
Page 19 and 20: OperationShutdown and Cleaning3. Re
Page 21 and 22: OperationCleaning Sprayer ExteriorW
Page 23 and 24: PartsParts ListRef. Part Descriptio
Page 25 and 26: TroubleshootingProblem Cause Soluti
Page 27 and 28: TroubleshootingProblem Cause Soluti
Page 29: RepairOutlet Valve5. Clean as much
Page 33 and 34: RepairClamshell6. Remove nut from g
Page 35 and 36: RepairMotor/Control Board Replaceme
Page 37 and 38: RepairSwitch Assembly5. Remove eigh
Page 39 and 40: RepairGear Replacement4. Remove fou
Page 41 and 42: Technical DataTechnical DataModels

3A2308A - Protective Coating Hand-Held Paint Sprayer, Operation ...

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?