238T Installation Manual

More documents

Recommendations

Info

TABLE OF CONTENTSPAGE NUMBER:DETAIL DESCRIPTIONA-1........................................TABLE OF CONTENTSA-2........................................GENERAL NOTESB-1........................................GENERAL INFORMATIONC-1........................................EAVE DRIP DETAILC-2........................................EAVE DRIP with GUTTER DETAILC-3 & C-4.............................FIXED RIDGE DETAILC-5 & C-6.............................FIXED HIGH EAVE DETAILC-7 & C-8.............................FIXED HIGH-SIDE TIE-IN DETAILC-9........................................FLOATING RAKE DETAILC-10......................................FLOATING RAKE DETAIL (ALTERNATE)C-11......................................FLOATING SIDE-WALL TIE-IN DETAILC-12 & C-13.........................VALLEY DETAILC-14 & C-15.........................VALLEY DETAIL (ALTERNATE)C-16 & C-17.........................HIP DETAILC-18......................................DEKTITE DETAILC-19 thru C-23......................CURB INSTALLATION DETAILSC-24 & C-25.........................TRIM LAP DETAILSA-1
GENERAL NOTESThe details shown on the following pages are suggestions or guidelines for installing the<strong>238T</strong> roof panel system. The installation details shown here are proven methods of construction,but they are not intended to cover all building requirements, designs or codes. The details mayrequire changes or revisions due to individual project conditions. In addition, other details maybe perfectly acceptable for use. Please contact McElroy Metal for assistance in determining if adetail is acceptable.<strong>Installation</strong> procedures shall be in accordance with the manufacturer's printed instructions, detailsor approved shop drawings. Installers should thoroughly familiarize themselves with allinstructions prior to beginning the installation process.The designer/installer is responsible to ensure the following:That the details here meet the particular building requirements.Awareness of and allowance for expansion/contraction of the roof panels.That adequate water tightness is maintained.That a proper uniform substructure is used to avoid panel distortion and that thesubstructure meets necessary code requirements.That all supporting members have been examined and are straight, level and plumb.McElroy Metal can provide all flashings and accessories shown in the installation drawingsunless noted otherwise. Panels, flashing and trim shall be installed true and in proper alignmentwith any exposed fasteners equally spaced for the best appearance. Sealant shall be field appliedon a clean, dry surface.Some field cutting and fitting of panels and flashings is to be expected and to be considered apart of normal installation work. Workmanship shall be of the best industry standards and withinstallation performed by experienced metal craftsmen.Oil canning of metal panels is inherent in the product and is not a cause for rejection. Plank orStriated panels are recommended as to reduce the appearance of oil canning.Contents of this manual are subject to change without notice. To confirm this book is the mostcurrent copy, please visit McElroy Metal's website at www.mcelroymetal.com.Optional details can also be found on our website.A-2
Page 4 and 5: GENERAL INFORMATIONSEAM ENGAGEMENTB
Page 6 and 7: EAVE DRIP w/ GUTTER DETAIL#14-10 X
Page 8 and 9: FIXED RIDGE DETAILMT-2: RIDGE CAP1/
Page 10 and 11: FIXED HIGH EAVE DETAILMT-25: HIGH E
Page 12 and 13: FIXED HEADWALL DETAILCAULKING(NOT B
Page 14 and 15: FLOATING RAKE DETAIL (ALT.)238T SEA
Page 16 and 17: VALLEY DETAILMT-10: VALLEY TRIM3/16
Page 18 and 19: VALLEY DETAIL (ALT.)MT-8: VALLEY TR
Page 20 and 21: HIP DETAILFIELD FOLD PAN OF PANEL3/
Page 22 and 23: DEKTITE DETAILDEKTITE PIPEBOOT238T
Page 24 and 25: ROOF CURB DETAIL238T ROOF PANEL0.08
Page 26 and 27: ROOF CURB DETAIL0.080 ALL-WELDEDALU
Page 28 and 29: TYPICAL TRIM LAP DETAILRAKE TRIM3/3

238T Installation Manual

Create successful ePaper yourself

Delete template?

Save as template?