RX100 Dome Interface Receiver - Videcon

More documents

Recommendations

Info

BBV Rx 100 Interface ReceiverAddendum to manual for the following domes:Panasonic WV-CS850 / 860Rx100 software RX1_P1V10Application NotesVariable speed Pan/Tilt.Zoom/Focus, Autofocus, Iris Open/Close (Hold for auto-iris)16 full scene presets2 preset patrols4 alarm inputs driving to preset 1 – 4Autopan/Patrol learn-play using autopan keyAdvanced Features Tx400 Tx1000 Tx1500 DM Sprite/DS/DS2/BX2ENTRY/EXIT Dome Menu ‘#’ 1 '#' WASH 1 ’#’ *889 002 or *889 10 10 2SET (select menu item) ‘#’ 2 '#' WIPE 2 ’#’ *889 003 or *889 10 10 3ESC (back to previous menu) ‘#’ 3 '#' AUTOPAN 3 ’#' *889 004 or *889 10 10 4SPECIAL2 (for special menus) ‘#’ 4 '#' LIGHTS 4 '#' *889 005 or *889 10 10 5A dome RESET ALL command can be sent by holding either ‘#’LIGHTS or ‘#’4 for 5 seconds when not within the menu. Care must be used with thiscommand as the dome is set to default and user settings are erased.The dome’s internal PATROL can be LEARNED using the dome menu. Setting the AUTO PAN KEY to PATROL will allow the patrol to be PLAYED bypressing AUTOPAN on the controller.RS485 control of dome. Connect dome FCC-68 plug into J7 of Rx100. If the dome cable requires extending, connect cores as follows:Dome Cable Description Rx100Yellow Data- J3/C1Green Data+ J3/C2Notes:The alarm output relay opens for approx 5 seconds upon power up. This can be used to signal power loss, etc.Accessing the dome menus.Press either '#'WASH , '#'1 or *889 002 key strokes to Enter Menu. Use Pan/Tilt to highlight item. Press either '#'WIPE, '#'2 or *889 003 key strokes to selectmenu item. ‘#’WASH , ‘#’3 or *889 004 is used to ESCAPE back to previous menu. SPECIAL2 menus are accessed using ‘#’LIGHTS, ‘#’4 or *889 005. Toexit from menu, press either '#'WASH, '#'1 or *889 002.Check with the multiplexer manual for exact procedure for entering * commands.Dome Switch settings: The following procedure must be followed to ensure that the dome is set-up correctly for terminated 4 wire RS485 at 19200 Baud andaddress 1. Remove the dome from it’s base before each step and reconnect to the base after changing the switches.Step 1: Address switches 2,4 and 5 ONStep 2: Address switches 1,3,4 and 5 ONStep 3: Address switches 1 and 8 ON. 4 Way switch 1 ON to select 4 wire, terminated RS485.Panasonic WV-CSR400/600/650 domes can be controlled using a different version of Rx100 software. Please contact BBV for further information or check outour web site www.bbvcctv.comRx100 installation manual V1.16 01May08.doc Page 24
BBV Rx 100 Interface ReceiverAddendum to manual for the following dome:Pelco Spectra (P-mode RS485 protocol)Rx100 software RX1_P2V10Application NotesVariable speed Pan/Tilt.Zoom/Focus, Autofocus16 full scene presets2 preset patrols4 alarm inputs driving to preset 1 - 4Dome Pattern definition and playbackAdvanced Features Tx1000 Tx400 DM-Sprite DM-DSL/DS/DS2Display dome menu (preset 95) '#' WASH '#' 1 *889 002 *889 10 10 2Enter within menu (iris open) '#' WIPE '#' 2 *889 003 *889 10 10 3Pattern define start '#' AUTOPAN '#' 3 *889 004 *889 10 10 4Pattern define stop ‘#’ LIGHTS ‘#’ 4 *889 005 *889 10 10 5To record a Pattern, direct the camera to the required starting position. Hold '#' and tap 'AUTOPAN'. The dome will now record pan/tiltand lens movement up to a time limit. To stop the recording, hold '#' and tap 'LIGHTS’. To play the recorded Pattern, press the AUTOPANkey only. The dome will repeatedly run the Pattern until either the joystick is moved or an alarm occurs.(The example shows Tx1000 keystrokes, please substitute the keystroke for the controller used.)Menu access:Use ‘#’ WASH to display menu. Navigate using the joystick and IRIS OPEN to select. When used with control systems without iris keys,eg DM Digital Sprite Lite, use *889 003 or *889 10 10 3Return to home: Can be programmed from the Dome menu.RS485 control of dome. Data rate, 9600 Baud, No parity, 8 Data bits, 1 Stop bitsConnection details:Dome Description Rx100RX- RS485(B) input J3/C1RX+ RS485(A) input J3/C2Notes:The alarm output relay opens for approx 5 seconds upon power up. This can be used to signal power loss, etc.Check with the DM multiplexer manual for exact procedure for entering * commands.Dome settings: Select dome address 1, P-MODE PROTOCOL and 9600, N, 8, 1.Link J6/1-2 is used to select the function that is used to drive the Esprit AUX outputs.Function Link fitted Esprit AUX No Link removed Esprit AUX NoLIGHTS 1 2WIPER 2 1WASHER 3 3Link J6/4-5 is used to enable 5 minute datum time to start preset patrol.Link fitted = datum disabled and link removed = datum enabled.Rx100 installation manual V1.16 01May08.doc Page 25
Page 1 and 2: RX100Dome Interface ReceiverInstall
Page 3 and 4: 1. PRE-INSTALLATION CHECKS AND SAFE
Page 5 and 6: 2. INTRODUCTIONGENERALThe Rx100 tel
Page 7 and 8: CABLE CONNECTION METHODFig. 1: cage
Page 9 and 10: 4. SETUPDIAGNOSTIC AIDSTwo red LEDs
Page 11 and 12: SEQPATROLPRESETCAMERAMONITORSELECTP
Page 13 and 14: BBV Rx100/24 Supply Additional info
Page 15 and 16: BBV Rx100 Interface ReceiverAddendu
Page 17 and 18: BBV Rx 100 Interface ReceiverAddend
Page 23: BBV Rx 100 Interface ReceiverAddend
Page 27 and 28: Using the advanced features when us
Page 31 and 32: Rx 100 Interface ReceiverAddendum t
Page 39 and 40: --- Blank for your notes ---Rx100 i

RX100 Dome Interface Receiver - Videcon

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?