PRIMERGY RX200 S4 - Nettailer

More documents

Recommendations

Info

System configurator and order-information guideD PRIMERGY RX200 S4 Status 2009-05-28Section III Memory- There are 12 memory slots for max. 48GB RAM ( Fully Buffered DIMM = FBD667 / PC2-5300F ) available( For explanation of following terms refer to section "Memory Configurations"- The memory area is divided into 2 branches with 2 channels each and 2 slots per channel- The first slot of each channel belongs to memory bank 1, the second slot belongs to memory bank 2the third slot belongs to memory bank 3- Each slot can optionally be equipped with 512MB, 1GB, 2GB or 4GB FBDIMM modulesNo mix of modules within one memory branch of bank1 or bank2 allowed.- Memory upgrade is only possible per branch with modul pairs( one pair per branch, max. two pairs / branch).- For each basic unit bank 1 of the first branch has to be equipped with one memory pair,(either 2x512MB = 1GB, 2x1GB = 2GB, 2x2GB = 4GB or 2x4GB = 8GB)Additional memory extensions can still be configured up to five times- For the function Memory Mirroring two identical memory module pairs regarding capacityare necessary in each branch of one memory bank. So following memory has to be ordered:1.) Minimum one time the same capacity like already is preinstalled in the basic unit has to be ordered2.) For additional memory 2x the same capacity has to be ordered- Hotspare Memory is supported per branch if the branch is fully populated- 4-way memory interleave technology for maximum performance is possible with2 memory module pairs in one memory bank (one pair per branch )- ECC with SDDC (Chipkill) is standard for RX200 S4.For a description of memory configurations refer to section "Memory Configurations"Minimum one Memory ( two modules ) = first Memory has to be selected for an orderable basic unitS26361-F3263-E521 S26361-F3263-E722 S26361-F3263-E723 S26361-F3263-E724Memory 1GB Memory 2GB Memory 4GB Memory 8GBFBD667 / PC2-5300F FBD667 / PC2-5300F FBD667 / PC2-5300F FBD667 / PC2-5300F6x consisting of consisting of consisting of consisting of2 single rank modules 2 dual rank modules 2 dual rank modules 2 dual rank modulesoccupies one branch occupies one branch occupies one branch occupies one branchMax. 6x per system Max. 6x per system Max. 6x per system Max. 6x per systemEFujitsu Technology Solutions x86 PRIMERGY Server 10 of 20
System configurator and order-information guideE PRIMERGY RX200 S4 Status 2009-05-28For the Memory Mirroring mode two identical memory modules pairs (branch 0 & 1) are necessary.( bank1 of branch 0 and 1 contain identical memory pairs )Therefore the following upgrade memory has to be ordered additionally:1.) Minimum one time the same capacity like the selected first Memory of the basic unit =2.) For addtitional memory 2x the same capacity =The function Memory Mirroring can be configured per BIOS setup.For mirrored memory configurations the following items have to be considered:Capacity: 50% of the configured memoryAvailability: Maximum memory availabilityAfter non-correctable errors or too many correctable errorsthe Mirror takes over immediately and the system remains online.Performance: 2-way interleave only in mirror configurations,therefore potentially not max. performance- Function Hot Spare Memory.- If three banks of one branch are equipped with memory pairs, the third bankcan be defined as hot spare memory bank. The capacity of the hot spare memory has to be equalor bigger than the capacity of the biggest capacity installed in the lower bank numbers.The function Hot Spare Memory can be configured per BIOS setup.For Hot Spare Memory configurations the following items have to be considered:Capacity:Availability:Performance:2/3 of the configured memory if the third bank is the hot spare bankand each bank is equipped with the same modul capacity.Less memory availability. Correction of single bit memory errors posssible.After non-correctable errors / too many correctable errors the system shuts downand during next reboot faulty memory becomes disabled.4-way interleave possible in max. spare mode configuration with two memory pairsper memory bank.4-way interleave increases system performance to maximumIn general it is recommended to use identical capacities over the branches of bank 1 to bank 3to ensure max. performance bandwidth. = = =bank 3FB-DIMM FB-DIMM FB-DIMM FB-DIMMbank 2FB-DIMM FB-DIMM FB-DIMM FB-DIMMbank 1F i r s tMemoryFB-DIMM FB-DIMM FB-DIMM FB-DIMMchannel 0 channel 1 channel 0 channel 1branch 0 branch 1Memory ControllersSection IV GraphicsGraphics Controller integrated in iRMC S2 (integrated Remote Management Controller):1600x1200x16bpp 60Hz, 1280x1024x16bpp 60Hz, 1024x768x32bpp 75Hz, 800x600x32bpp 85Hz, 640x480x32bpp 85Hz(1280x1024x24bpp 60Hz only possible if local monitor or remote video redirection is off)FFujitsu Technology Solutions x86 PRIMERGY Server 11 of 20
Page 1 and 2: PRIMERGY RX200 S4System configurato
Page 3 and 4: System configurator and order-infor
Page 9: System configurator and order-infor
Page 15 and 16: S y s t e m c o n f i g u r a t o r

PRIMERGY RX200 S4 - Nettailer

Create successful ePaper yourself

Delete template?

Save as template?