DynojetPS08:Layout 1.qxd - Dynojet Research

More documents

Recommendations

Info

Ignition ModuleThe Dynojet Ignition Module is an “add on” accessory for select PowerCommander III USB. It allows you to control and adjust the ignition timingof your motorcycle’s engine.Rev X-tendOn select models of bikes our Rev X-tend feature isavailable when using the Ignition Module. Rev X-tend makesit possible to increase the RPM limit from the factory setting.This feature is intended to be used on engines that havebeen modified to allow the increased RPM limit.Go to www.powercommander.com for a list of Rev X-tendbike applicationsThe Ignition Module is connected to the PCIIIUSB with it’s built in expansion port link and communicates via a CAN interface. As in the case of thePower Commander, the Ignition Module uses OEM style connectors to plug in-line of the stock ignition harness so no cutting or splicing is required.The Ignition Module uses “direct coil driver technology” and allows a high degree of timing adjustment. In the Power commander Control CenterSoftware the user is able to advance or retard the ignition curve up to 10 degrees based on throttle position and RPM. It is also possible to alterthe timing for each cylinder individually if necessary.The Ignition Module comes standard with no adjustments made in the map for the timing table. Due to different states of tune, fuel quality, and enginemodifications we found it is best to leave the ignition timing stock for safety reasons. To have your ignition curve fine tuned Dynojet recommendsbringing your bike to one of our Authorized Power Commander Tuning Centers. These centers have the necessary dynamometer equipment toextract the most performance out of the Ignition Module.On motorcycles that have eight injectors and were not previously able to benefit from the use of the Dynojet Quick Shifter, the Ignition Module nowallows this functionality. The Dynojet Quick Shifter is connected to the expansion port between the Ignition Module and the PCIIIUSB.For available models please refer to the Power Commander application chart pages 5-914 Power Commander Accessories 2008Not for use with EX model Power Commanders
Available HarnessesHUB-001Multi-Function HubMap Selection SwitchConnecting the Map Selection Switch allowsthe rider to switch between two different mapswithin the Power Commander. For TouringBikes, this could be used to switch between a"fuel economy map" for long rides and a "fullperformance map". For Sport Bikes, it could beused for applications such as "Dry NitrousOxide" kits to permit the user to make the fuelmixture richer when activating the system.Additionally, if the Power Commander has anIgnition Module connected, it can switch to aless aggressive timing map at the same time.76950320-SWITCH ONLY61329304Gear Position/Speed InputFuel and ignition timing (when using theDynojet Ignition Module) adjustments can bemade based on gear position. If the user wantsto advance the timing in lower gears whileretarding it in higher gears, this input makesthat possible.Pressure InputWhen using a Power Commander onturbocharged applications, the Boost Inputoption makes it possible to have the fuelautomatically increase with boost level. Insituations where the user has an adjustableboost controller, this makes remapping eachtime the boost level is changed unnecessary.Relay HarnessBased on the data from the PowerCommander and the inputs from the Multi-Function Hub, a solenoid, relay, warning light,etc. can be triggered. This can be used toactivate items such as a shift light, NitrousOxide system, or air shifter.769502127695001276950506Hub only (no harnesses included, must add from list below as needed)The Multi-Function Hub allows users toaccess advanced expansion features. Severaloptional harnesses are available to permitboth input and output to/from the module.Hub with map switch & handle bar bracketHub with map switch/bracket and gear position, relay, boost harnesses (no connector)HUB-001HUB-002HUB-003Switch/harness only 76950320Bracket (switch) 61329304Gear Position harness 76950212Relay harness 76950506Boost input harness (bare ends, no connector) 76950012Boost input harness (With General Motors 3 BAR pressure sensor connector) 76950325Power Commander Accessories 2008 15
Page 2 and 3: WINNERS USE DYNOJETErion RacingJosh
Page 4: RACE READY PERFORMANCE• Works wit
Page 7: Expansion port for upgrades and acc
Page 10 and 11: • Works with any exhaust• Rev X
Page 12 and 13: ACCESSORIESMulti-Function HubColor
Page 16 and 17: Quick ShifterThere are three basic
Page 19 and 20: Thunderslide KitsThunderslide for H
Page 21 and 22: CC Year Model Stage Part# CodeKawas
Page 23 and 24: ATV and OFF-Road Jet KitsGet the mo
Page 25 and 26: CC Year Model Stage Part # CodePola
Page 27 and 28: AustraliaSerco Pty Ltd34 Veronica S

DynojetPS08:Layout 1.qxd - Dynojet Research

Create successful ePaper yourself

Delete template?

Save as template?