Tool Holders - Hardinge

More documents

Recommendations

Info

CHNC ® IIICHNC ® IIISPPage 18"Crush- & Cut-Type" Knurling Tools“Crush-Type” Knurling ToolThe knurling tool mounts into a round shank tool holder and comes standard with twoknurls. The 64 diametrical pitch knurling wheels are mounted into swivel holders that canbe set at any angle to form either diamond or straight knurls. This unit can knurl aworkpiece using a cross slide motion (approaching the work perpendicularly), or aturning motion by placing the holder parallel to the workpiece and passing the workpiecebetween the knurls.By making the appropriate adjustments, diameters from 5 ⁄32" to 1 ⁄2" (3.97 to 12.70mm) forthe T8- 5 ⁄8 model and to 3 ⁄4" (19.05mm) for the T8- 3 ⁄4 model can be knurled. A workpiecewith a diameter of 3 ⁄8" (9.53mm) or less can pass through the shank of the knurling tool.For stock diameters of 3 ⁄8" to 1 ⁄2" (9.53 to 12.70mm), the maximum knurling length is 7 ⁄8"(22.23mm).30L003 04 5WZYModel Part DimensionsNo. Number A B C D G H K L QT8- 5 ⁄8 STA-0010901 Inch 1.63 1.13 2.75 .6243 2.06 .390 .5002 .500 1.00mm 41.30 28.60 69.90 15.857 52.40 9.90 12.704 12.70 25.40T8- 3 ⁄4 STA-0010901-75 Inch 2.44 1.49 3.93 .7493 2.80 .450 .6252 .800 1.38mm 61.90 37.90 99.80 19.031 71.00 11.30 15.879 20.30 35.10W – Washer X – Cutting Wheels Y – Cap Screw Z 1 – Set Screw3-0010901 T8- 5 ⁄8 (8-0010901) & T8- 3 ⁄4 (ST-0010901) 0100208 0550506FXHAKCBGD“Cut-Type” Straight Knurling ToolThe “cut-type” straight knurling tool is used to generate a straight knurl by cutting themetal.The tool holder shaft mounts into a 5 ⁄8" round shank tool holder and comes standard withone knurl. The knurl has a 3 ⁄4" (19.05mm) OD and 1 ⁄4" (6.35mm) ID with a width of 1 ⁄4"(6.35mm).YModel Part DimensionsNo. Number B C D EAHC31 KH-0011762 Inch 2.25 2.63 .624 .500mm 57.20 66.70 15.85 12.70Y – Cutting WheelsST-0010901-DECBDCall 800-843-8801Monday—Friday, 8:00 am to 8:00 pmEastern Standard Time for FAST delivery!Hardinge Inc.Elmira, New York 14902-1507 USA© Hardinge Inc., 2001All specifications subject to change without notice.Unless indicated otherwise, all marks indicated by ® and are trademarks of Hardinge Inc.
Adjustable & Revolving StopsCHNC ® IIICHNC ® IIISPPage 19The revolving stock stop is used in a round shank tool holder to position bar stock in thecollet while being fed by a bar feed unit. The front portion of the stop rotates with theworkpiece.The adjustable stop has a maximum length adjustment of 7 ⁄8" (22.23mm).Adjustable Revolving Stock StopLDABModel Part DimensionsNo. Number Min A Max A B D LT20- 5 ⁄8 RSA-0011157 Inch .750 1.63 1.13 .624 .810mm 19.10 41.30 28.60 15.85 20.60T20- 3 ⁄4 RSA-0011157-01 Inch .750 1.63 1.13 .749 .810mm 19.10 41.30 28.60 19.03 20.60The revolving stock stop mounts into a round shank tool holder directly, or with a bushing,to position bar stock in the collet while being fed by a bar feed unit. The front portion ofthe stop rotates with the workpiece.Revolving Stock StopLDACBModel Part DimensionsNo. Number A B C D LT20- 3 ⁄4-16 RS-0011157-16 Inch 1.06 1.38 2.44 .749 1.44mm 27.00 34.90 61.90 19.04 36.50© Hardinge Inc., 2001All specifications subject to change without notice.Unless indicated otherwise, all marks indicated by ® and are trademarks of Hardinge Inc.Hardinge Inc.Elmira, New York 14902-1507 USACall 800-843-8801Monday—Friday, 8:00 am to 8:00 pmEastern Standard Time for FAST delivery!
Page 4 and 5: CHNC ® IIICHNC ® IIISPPage 4Misce
Page 6 and 7: CHNC ® IIICHNC ® IIISPPage 6Exten
Page 8 and 9: CHNC ® IIICHNC ® IIISPPage 8Hardi
Page 10 and 11: CHNC ® IIICHNC ® IIISPPage 10Inve
Page 13 and 14: Triple Tool HolderCHNC ® IIICHNC
Page 15 and 16: Adjustable Tool Holder & 1C Collet
Page 17: Double-Angle Collet Tool HolderCHNC
Page 21 and 22: Bar Stock PullerCHNC ® IIICHNC ®
Page 23 and 24: Single, Double & Triple Tool Holder
Page 25 and 26: Quadruple Tool Holder & Universal T
Page 27 and 28: This knurling tool mounts directly
Page 29 and 30: Cut-Off Blade & InsertCHNC ® IIICH
Page 31 and 32: Releasing & Self-Feeding Die Holder
Page 33 and 34: Tool Touch Probe & Parts Removal Sy
Page 35 and 36: Voltage Transformer & Foot SwitchCH
Page 37 and 38: MiscellaneousCHNC ® IIICHNC ® III

Tool Holders - Hardinge

Create successful ePaper yourself

Delete template?

Save as template?