- Page 1: University of Western SydneyIn Conj
- Page 5 and 6: • 90% of the electricians of the
- Page 7 and 8: 2.1.3 Electrical Hazards 102.1.3.1
- Page 9 and 10: 4.2.11 Allergy 695 Summary, Conclus
- Page 11 and 12: Content of the StudyIn Chapter One,
- Page 15: List of IllustrationsIllustration T
- Page 18: 1. IntroductionThis project focuses
- Page 24 and 25: 2 The Study of Related Literature2.
- Page 26 and 27: life, against which they have no de
- Page 28 and 29: CurrentReaction1 milliamp Just a fa
- Page 30 and 31: Codes ofPracticesGovernmentPublicEd
- Page 32 and 33: • determine what can be done to r
- Page 34 and 35: 2.2.4 Personal Protection DevicesTh
- Page 36 and 37: Table 2 Classification of Work Cate
- Page 38 and 39: Table 3 Grouping of Personal Protec
- Page 40 and 41: Table 4 Selection Specification (So
- Page 42 and 43: Table 5ProcedureConduct a riskasses
- Page 44 and 45: 2.3.1 Hierarchy of Control on Elect
- Page 46 and 47: from electricity in work activities
- Page 48 and 49: • Maximum allowable current to pa
- Page 50 and 51: • Circumference of wrist• Circu
- Page 52 and 53:
andProof Test Voltage is either the
- Page 54 and 55:
2.4.4 BS 697 : 1986, Specification
- Page 56 and 57:
2.4.6 JIS T 8112, Rubber gloves for
- Page 58 and 59:
2.5 Summary: What is Known and What
- Page 60 and 61:
3 Survey on the Selection and Use o
- Page 62 and 63:
The electricians in the pilot study
- Page 64 and 65:
3.2.3 Sampling StrategyThere is no
- Page 66 and 67:
A flowchart was prepared to help th
- Page 68 and 69:
4. Results of the Study4.1 Profile
- Page 70 and 71:
4.2 Profile of the Electricians und
- Page 72 and 73:
4.2.3 Years of Electrical Work Expe
- Page 74 and 75:
4.2.4 Risk Assessment and Safety Ac
- Page 76 and 77:
Table 22 tabulates the response of
- Page 78 and 79:
Table 24 indicates the ranking of r
- Page 80 and 81:
4.2.7 Where Were Insulating Gloves
- Page 82 and 83:
Majority of the relies focused on p
- Page 84 and 85:
Figure 17 shows that 55% of the REW
- Page 86 and 87:
4.2.11 AllergyIn response to the in
- Page 88 and 89:
applications and subsequent date re
- Page 90 and 91:
5.3 RecommendationsBased on the fin
- Page 92 and 93:
5.3.1.2 Special contact requirement
- Page 94 and 95:
Illustration 1. To determineglove s
- Page 96 and 97:
5.3.1.6 Puncture, snag, tear and cu
- Page 98 and 99:
5.3.2.1 Air TestAir test should be
- Page 100 and 101:
5.3.2.3 StretchingStretch the thumb
- Page 102 and 103:
5.3.3 Maintenance Guide5.3.3.1 Stor
- Page 104 and 105:
ReferenceAdam, J. 1995, Risk, UCL P
- Page 106 and 107:
IEE - Health and Safety Briefing 34
- Page 108 and 109:
Occupational Safety and Health Conv
- Page 110 and 111:
Youngman, M. B. 1982, REDIGUIDE 12
- Page 112 and 113:
Guidance NotesonThe Selection, Use
- Page 114 and 115:
4. Electrical HazardsElectrical saf
- Page 116 and 117:
5. Protective StrategiesUnder Secti
- Page 118 and 119:
5.4 Hierarchy of Control on Electri
- Page 120 and 121:
BS EN60903: 1993;D120-95 of ASTM199
- Page 122 and 123:
6.5 Size and fitProper size and fit
- Page 124 and 125:
6.6 Puncture, snag, tear and cut re
- Page 126 and 127:
7.2 Hand Rolling and Pinch RollingS
- Page 128 and 129:
8. Care and Maintenance of Insulati
- Page 130 and 131:
Electrical Protective Gloves Survey
- Page 132 and 133:
HAVE YOU CONSIDERED THE FOLLOWING F
- Page 134 and 135:
Appendix CQuestionnaire (Chinese) o
- Page 136 and 137:
9. / (Lockout/Tagout Procedure)? 1
- Page 138:
30. ?, , ___________________31. ?