CAT-1001_MR ... - Secutron

CONVENTIONALFIRE ALARM CONTROL UNITSMR-2602Two Zone Fire Alarm Control UnitDescriptionSecutron's MR-2602 is a versatile, power-packedfire alarm control unit designed for small building fireprotection. With its exceptional feature set, a power supplythat will handle the panel’s full rated load and flexible frontpanel programming for quick and simple configuration tosuit the application at hand, the MR-2602 is a powerful,versatile unit, ideally suited for small, fast turnaround fireapplications.The MR-2602 is equipped with two Style B (ClassB) initiating circuits, two Style Y (Class B) notificationappliance circuits, one Form "C" common alarm relay, oneForm "C" common trouble relay, one non-switched Aux.Power output and one switched Aux. Power output. Thepanel also has individual alarm, supervisory and troubleLED indicators per zone.The panel features a 6.0A power supply which providesa full 3.0A of NAC power, 0.5A Aux. power with thebalance to run the panel and charge the batteries. Noextra transformers or added power supplies are required.In addition the panel has 500mA of Auxiliary power withswitched and unswitched outputs.The MR-2602 is field programmable from the front panelusing the front panel LEDs and switches for simple, quickprogramming. All initiating and indicating circuits as wellas system functions are configured from the front panel.Features• Listed to UL 864, 9th edition• 2 Style B (Class ‘B’) dual-use zones• 2 Style Y (Class ‘B’) notification appliance circuits• 6 Amp power supply• 500mA of Aux. power• Common alarm relay• Common trouble relay• Integral battery charger• ‘Secur-Bus’ for dialer and remote annunciation• Event buffer• Six programmable zone options• Class A capability, both NAC and Zones• One-man walk test• Programmable NAC silence timer• 3 LEDs per zone• Front panel programmingOptional Modules• City tie/polarity reversal module• Relay module• Style D (Class A) zone module• Remote 5 zone LED annunciator• Flush trim ringEach initiating circuit can be individually configured asNull (zone not used), Instant (smokes, contacts instant),Verify (smokes verified, contacts instant), Waterflow,Supervisory or 4-Wire Verify.An optional Style D (Class A) converter module convertsboth Style B (Class B) initiating circuits to Style D (Class A).Each NAC zone is power limited and provides 1.5A at24VDC full wave rectified for heavy duty signal loads. TheNAC circuits can be configured for Steady, Temporal orStrobe. The notification circuits are jumper selectable tobe configured as one Style Z (Class A) zone.The MR-2602 utilizes "Secur-Bus" which is a 4 wire portfor communication and power to accessory components.All Secur-Bus components are supervised. Secur-Buscomponents include the Dual line dialer modules and theremote LED annunciators.MEAapprovedS6619 S6619 7165-1656:111 352-03-EIssue 4 SECUTRONPage 1 of 2Canada 25 Interchange Way, Vaughan (Toronto), Ontario L4K 5W3 Telephone: (905) 695-3545 Fax: (905) 660-4113 • Web Page: www.secutron.comU.S.A. 4575 Witmer Industrial Estates, Niagara Falls, NY 14305 Telephone: (888) 695-3545 Fax: (888) 660-4113 • E-mail: mail@secutron.comCatalog Number 1001 • Not to be used for installation purposes.

Engineering SpecificationsThe contractor shall supply a 2 zone, fully supervised fire alarmcontrol panel. The panel shall supervise and monitor both 2-wire smoke detectors and contact alarm initiating devices oneach two-wire zone.The control panel shall be complete with two Style B (Class ‘B’)alarm initiating zones, two Style Y (Class ‘B’) notification appliancecircuits, one Form ‘C’ common alarm relay, one Form ‘C’ commontrouble relay, one non-switched Aux. power output, and oneswitched Aux. power output. The panel shall include individualalarm, supervisory and trouble LED indicators per zone.Each alarm initiating zone shall be capable of beingindividually programmed for smoke/contact instant alarm,smoke auto-verify and contact instant, supervisory, waterflow or four-wire smoke auto-verify service. Each alarminitiating zone shall limit the maximum current to 60mA andbe supervised for opens and ground faults. An optionalmodule that mounts inside the cabinet shall be available toconvert the two alarm initiating zones to Style D (Class ‘A’).Each notification appliance circuit shall be supervised for opens,shorts and ground faults. Each notification appliance circuitshall be capable of being individually programmed as steadyor temporal (ANSI cadence). Each notification appliance circuitshall supply 24VDC full wave rectified at 1.5A and be powerlimited. NAC’s shall be capable of being jumper programmed tooperate as a single Style Z (Class ‘A’) NAC. NAC #2 shall alsobe capable of being programmed as strobe whereby the NACwill only silence after the panel is reset.The total Aux. power shall be 24VDC, 500mA max. and bepower limited. The control panel power supply shall support theAux. power (0.5A), the two NAC’s (3.0A), the battery charger(0.35A) and the control panel without the addition of any otherpower supplies or components.Technical DataAC PowerNAC 1NAC 2NAC 1/2 as StyleZ (Class A)ZonesDAT/CLKAux+COMSCOM120V 60Hz 1.5A, 240V 50Hz24 VDC full-wave rectified, 1.5A max., PTC overloadprotected, power limited, Style Y, (Class ‘B’)24 VDC full-wave rectified, 1.5A max., PTC overloadprotected, power limited, Style Y (Class ‘B’)24 VDC full-wave rectified, 1.5A max., PTCoverload protected, power limited24 VDC filtered regulated, 60mA alarm currentmax., power limited,100 ohms max. line resistanceData and clock line for remote modulecommunications. (Secur-Bus)24 VDC filtered regulated, 500mA max., PTCoverload protected, power limitedNon-switched return for AUX+ power, 500mASwitched return for AUX+ power, 500mANote: The 500mA from AUX+ is shared between the COM andSCOM returns. Internal and remote module power is supplied fromthe AUX+ and COM supply.Alarm relaycontactsTrouble relaycontactsBattery chargerCabinet30 VDC, 2A max.30 VDC, 2A max.24 VDC, 350mA max. Will charge up to 16AH*sealed lead-acid batteries max.14 1/2” W x 15” H x 4 1/4” D - Red*External cabinet required for batteries larger than 12AH.The control panel shall include a four-wire output which shallprovide power and communication for up to four remote troubleindicators and up to four remote alarm annunciator/troubleindicators. Each remote shall be supervised for its presence.The panel shall accommodate, within the cabinet, an optionalthree (3) relay module. Each relay shall be Form C andbe individually selectable for alarm, supervisory or troubleoperation. Relay contacts will be rated at 2A @ 30 VDC.The control panel shall accommodate, within the cabinet, anoptional local energy city-tie/polarity reversal combinationmodule.The control panel shall include individual trouble indicators forNAC 1, NAC 2, battery, ground, signals silenced, commonalarm, common trouble and AC on. The control panel shall alsoinclude controls for trouble silence, signal silence, system resetand lamp test. The switch to put the panel into the programmingmode or walk test mode shall only be accessible by a qualifiedinstaller. Indicators shall always be visible and the user controlsshall only be accessible once the locked cabinet door is opened.Access to batteries and system components shall be userrestricted by complete dead-front construction.The panel shall include programmable options for a 60 sec.silence inhibit period, water flow silence inhibit, automaticNAC silence and silent/audible one man walk test. All panelprogramming shall be done using the front panel controls andindicators. Program data shall be stored in non-volatile memorythat retains the information when all power is removed fromthe panel. The panel shall also include an event buffer that isinstaller accessible so that the last 20 events can be reviewed.Ordering InformationModelDescriptionMR-2602 Two Zone Fire Alarm Control UnitsMR-2602RAccessoriesMR-2602-AMR-2605-R3MR-2801BMR-2605-TMR-2605-ATMR-2605FT-BTwo Zone Fire Alarm Control Unit, RedTwo Zone Style D (Class A) ModuleThree Programmable Form "C" Relays, 2A@30VDCLocal Energy & Polarity Reversal ModuleRemote Trouble IndicatorRemote Trouble & Alarm IndicatorFlush Trim Ring, BlackPage 2 of 2 SECUTRONCatalog Number 1001 • Not to be used for installation purposes.Issue 4Secutron reserves the right to make changes at any time without notice in prices, colors, materials, components, equipment, specifications and models and also to discontinue models.