NEC XN120 EXIFU Guide.pdf 3006KB 02 Mar 2013 - Telephone ...

More documents

Recommendations

Info

Call Logging (SMDR)Serial CableThe serial cable used to connect the EXIFU card to the PC must be a null modem type (cross cable).The following connections are required.The EXIFU card has a 9 pin male D-Type connector.The cable must not exceed 15 metres long.9-Pin to 9-Pin CableSystemSMDR DeviceSignal NamePin No.Pin No.Signal NameRXD22RXDTXD33TXDDTR44DTRSG55SGDSR66DSRRTS77RTSCTS88CTS1 51 56 96 99-Pin to 25-Pin CableSystemSMDR DeviceSignal NamePin No.Pin No.Signal NameRXD22TXDTXD33RXDDTR44RTSSG55CTSDSR66DSRRTS77SGCTS820DTR1 513 16 925 1426 XN120 EXIFU Guide
Compact Flash SocketThe compact flash socket of the EXIFU-A1 card can be used for either saving/re-loading the systemconfiguration or upgrading the XN120 main unit’s firmware.Compact FlashSaving the system configurationYou can save a copy of the customer configuration that can be re-loaded in the event of system failure.You will need a compact flash card with at least 4MByte of free capacity.The XN120 will save the configuration in a folder named DATA on the flash card. If the flash card already has aDATA folder it will be overwritten each time the configuration is saved.To save the customer configuration.CAUTIONThe XN120 operation may be effected during the data save.Do not perform a save when the system is under load.1 Remove the sub and maincovers of the XN120 main unit.2 Insert the compact flash cardinto the socket on the EXIFUYou do not need to power off the XN120 to insert the card.3 Program 90-03-01Save configuration.90-03-01Data Save 1Enter 1 to save the configurationPress DC to exitEnter 1.Press HOLD to confirm the entry.The display will show the following while saving.90-03-01SavingSystemDataWhen complete the display will show the next programnumber.90-04- M’tenancLoad DataPress DC several times when you are done to return to theProgram Mode.(Press SPK to save changes and exit if you are finished).4 When the save is completeyou can remove the compactflash cardYou do not need to power off the XN120 to remove the card.Unsure you hold the EXIFU card when removing the flash card – seecaution below.CAUTIONYou must ensure that the EXIFU card is not unplugged when you remove the compact flash cardotherwise the system will reset.If the EXIFU card is unplugged DO NOT plug it back in until you have powered off the XN120 system.XN120 EXIFU Guide 27
Page 2 and 3: ContentsWhat is the EXIFU?.........
Page 4 and 5: Installation ProcedureInstallation
Page 6 and 7: Install the EXIFU Card2- Install th
Page 8 and 9: Test the EXIFU Card3- Test the EXIF
Page 10 and 11: Configure the EXIFU Card4- Configur
Page 12 and 13: Configure the EXIFU CardMaking Chan
Page 14 and 15: Ethernet PortEthernet Port Specific
Page 16 and 17: Call Logging (SMDR)Set the Baudrate
Page 18 and 19: Call Logging (SMDR)Sample SMDR Repo
Page 20 and 21: Call Logging (SMDR)SMDR Output Opti
Page 22 and 23: Call Logging (SMDR)Extension name o
Page 24 and 25: Call Logging (SMDR)DDI or CLIP numb
Page 28 and 29: Compact FlashSystem ReportIt is rec
Page 30 and 31: Compact FlashUpgrade the XN120 Main
Page 32 and 33: Compact Flash8 Set the NORMAL switc

NEC XN120 EXIFU Guide.pdf 3006KB 02 Mar 2013 - Telephone ...

Create successful ePaper yourself

Delete template?

Save as template?