User's Manual - from Measurement Computing

More documents

Recommendations

Info

12. Plug in all cords and cables that were removed in step 3.13. Apply power to, and start up the PC.Note: At this point some PCs may prompt you to insert aninstallation disk. While this is rare, if you do receivesuch a prompt simply place the install CD into the diskdrive and follow the screen prompts.Securing a DaqBoard/2000c Series BoardStep 3 – Configure BoardsDaqBoard/2000c Series boards have no jumpers or switches to set. Configuration is performed entirely through software.Refer to the following figure and steps to complete the configuration. The numbers in the figure correspond to the numberedsteps immediately following the figure.Accessing the DaqBoard/2000 Properties TabIG-4 DaqBoard/2000c Series Installation Guide 979294 1061-0940, rev 4.0
1. Run the Daq Configuration control panel applet. Navigation from the desktop to the applet is as follows:Start ⇒ Settings ⇒ Control Panel ⇒ Daq*Configuration (double-click)2. Double-click on the Device Inventory’s DaqBoard2K0 icon. The DaqBoard/2000 Properties tab (used for the entireDaqBoard/2000 Series) will appear. If the DaqBoard2K0 icon is not present, skip to the Using ‘Add Device’ sectionprovided below.3. Enter a “Device Name” in the text box, or use the default “DaqBoard2K0.” Device Name is for identifying the specificDaqBoard/2000 Series board. Note that Device Name actually refers to the PCI slot and not to the actual board.4. Verify that the “Device Type” shows the correct DaqBoard/2000 Series board, e.g., “DaqBoard/2000, DaqBoard/2001,etc.” Note that available device types can be viewed via the pull-down list ().5. Confirm that the DaqBoard/2000 Series text box shows a Bus #, Slot #, and Serial Number.If this text box is empty, use its pull-down list () and select the serial number that matches the one for your board.Refer to the inside front cover page for serial number information.Using “Add Device”This method is for users who have accessed the Daq Configuration control panelapplet, but have no DaqBoard2K icon (as described instep 2, above).(A) After accessing the Daq Configuration control panel applet, click on the AddDevice button (see figure, right). The Select Device Type window will appear.(B) Using the Device Type’s pull-down list, select the applicable board. In theexample at the right DaqBoard/2000 is selected.(C) Click the OK button. The DaqBoard/2000 Properties tab will appear. This tabapplies to all boards in the DaqBoard/2000 Series.At this point, complete steps 3 through 5 from above.Using “Add Device’Step 4 – Test HardwareUse the following steps to test the DaqBoard/2000 Series board. Note that these steps are continued from those listedunder the previous section, “Configure Board.”1. Select the “Test Hardware” tab.2. Click the “Resource Test” button.3. After the test is complete, click “OK.”System capability is now tested for the DaqBoard/2000Series board and a list of test results appears on screen.Note: If you experience difficulties, please consult your userdocumentation (included on your CD) before calling fortechnical support. Note that the user documentationincludes a troubleshooting chapter, as well as a greatdeal of information regarding specific DBK cards andmodules.Test Hardware Tab (Condensed Screen Image)At this point we are ready to connect signals. This is typically accomplished with the use of a DBK200 Series option.Reference Note:For detailed information regarding the DBK200 Series options, refer to the DBK Option Cards and ModulesUser’s Manual (p/n 457-0905).During software installation, Adobe ® PDF versions of user manuals are automatically installed onto yourhard drive as a part of product support. The default location is in the Programs group, which can beaccessed from the Windows Desktop. A copy of the Adobe Acrobat Reader ® is included on your CD. TheReader provides a means of reading and printing the PDF documents. Note that hardcopy versions ofmanuals can be ordered from the factory.1061-0940, rev 4.0 979294 DaqBoard/2000c Series Installation Guide IG-5
Page 1: DaqBoard/1000 and /2000 Series User
Page 4 and 5: Your order was carefully inspected
Page 6 and 7: viDaqBoard/1000 and /2000 Series Us
Page 8 and 9: This page is intentionally blank.vi
Page 10 and 11: This page is intentionally blank.x
Page 12 and 13: Reference Notes:(1) Each DaqBoard p
Page 14: 7. Refer to the figure at the right
Page 17 and 18: DaqBoard/2000c SeriesInstallationTh
Page 19: CAUTIONTurn power OFF, and UNPLUG t
Page 23 and 24: Daq Systems and Device Overviews 1D
Page 25 and 26: Theory of OperationI/O Comparison M
Page 27 and 28: Synchronous Output OperationsThe Da
Page 29 and 30: DaqBoard/100016 AnalogInput2 Analog
Page 31 and 32: DaqBoard/100516 AnalogInputs24 Digi
Page 37 and 38: DaqBoard/200240 DigitalI/O4 Counter
Page 39 and 40: DaqBoard/20034 Analog OutputsDBK205
Page 41 and 42: DaqBoard/20044 AnalogOutput40 Digit
Page 43 and 44: DaqBoard/200516 AnalogInput40 Digit
Page 45 and 46: Using DBK Cards and Modules for Sig
Page 47 and 48: Specifications - DaqBoard/1000 Seri
Page 49 and 50: Analog OutputsApplicable to DaqBoar
Page 51 and 52: Specifications - DaqBoard/2000 Seri
Page 53 and 54: Input Sequencer Applicable to DaqBo
Page 55 and 56: Pattern Generation Output Applicabl
Page 57 and 58: Connections and Pinouts, DaqBoard/1
Page 59 and 60: Pinout for DaqBoard/1000 and DaqBoa
Page 61 and 62: Connections and Pinouts, DaqBoard/2
Page 63 and 64: DBK201The DBK201 P4-to-P1/P2/P3 ada
Page 65 and 66: DBK207 and DBK207/CJCThe DBK207 and
Page 67 and 68: DBK209The DBK209 is a mini-adapter
Page 69 and 70: P1 for DaqBoard/2000 Series and /20
Page 71 and 72:
P3 for DaqBoard/2000 Series and /20
Page 73 and 74:
P4 Pin Signal Type Description P1,
Page 75 and 76:
Ground Tables - P4 Pin to P1, P2, a
Page 77 and 78:
CE-Compliance 4Overview ……4-1CE
Page 79 and 80:
CE Enhancements for DBKsThe followi
Page 81 and 82:
For cPCI DaqBoard/2000c Series Boar
Page 83 and 84:
Calibration 5DaqBoard/1000 and /200
Page 85 and 86:
GlossaryAcquisitionAnalogAnalog-to-
Page 87 and 88:
TriggerTTLUnipolarAn event to start
show all

User's Manual - from Measurement Computing

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?