1.0 - SATA-IO

More documents

Recommendations

Info

©LeCroy CorporationFigure 3. Image of VdiffMin measurement for a product running at 3.0Gb/s transmitting HFTPLeCroy Corporation 20 SATA PHY, TSG, OOB LeCroy MOI rev 1.4 version 1.0
©LeCroy CorporationFigure 4. Image of VdiffMax measurement for a product running at 3.0Gb/s transmitting MFTPTest Setup:Channels 2 and 3 of the oscilloscope are connected to the transmitter pair on the SATA test fixture. Fordevices this is 5 and 6, and for hosts it is 2 and 3. The SATA test fixture is inserted into the PUT. For hosts, this testshould be done on the worst case port identified. See Reference [5] for details.Test Procedure:The channels should be deskewed before performing this test. See Appendix A for details. The testprocedure then proceeds as follows:1) Open the QualiPHY SATA PHY, TSG, OOB test suite. See Appendix B for details.For products that support 3.0Gb/s, steps 2-5 must be performed at both 1.5Gb/s and 3.0Gb/s speeds:2) Select an appropriate configuration with TSG-01 selected.3) Run the test.4) When prompted to produce a required test pattern, set the product to generate that pattern. SeeAppendix C for details. Check the pattern on the oscilloscope to make sure it is correct. Press“OK” to continue.5) When the test completes, generate a report. Observe the results for TSG-01 in the report. Theindividual results for VdiffMin with HFTP, MFTP and LBP are reported as DH, DM andVTestLBP, respectively. Each value “passes” if it meets the VdiffMin requirements. Theminimum of the three values should be recorded as VdiffMin. TSG-01 passes if VdiffMinpasses.Observable Results:VdiffMin shall be at least 400 mV. The values of pu and pl are provided only for informational purposes.Possible Problems: See PHY-01.LeCroy Corporation 21 SATA PHY, TSG, OOB LeCroy MOI rev 1.4 version 1.0
Page 1 and 2: ©LeCroy CorporationSerial ATAInter
Page 3 and 4: ©LeCroy CorporationAPPEDIX A - IFO
Page 5 and 6: ©LeCroy CorporationMarch 25, 2009
Page 7 and 8: ©LeCroy CorporationITRODUCTIOThe t
Page 9 and 10: ©LeCroy CorporationREFERECESThe fo
Page 11 and 12: ©LeCroy CorporationTest PHY-01 - U
Page 13 and 14: ©LeCroy CorporationTest PHY-02 - F
Page 15 and 16: ©LeCroy Corporation0.1 kHz higher
Page 17 and 18: ©LeCroy CorporationTest PHY-04 - S
Page 19: ©LeCroy CorporationTest TSG-01 - D
Page 23 and 24: ©LeCroy CorporationObservable Resu
Page 25 and 26: ©LeCroy CorporationPossible Proble
Page 27 and 28: ©LeCroy CorporationTest TSG-05 - R
Page 29 and 30: ©LeCroy CorporationTest TSG-07 - G
Page 45 and 46: ©LeCroy CorporationPHY OOB REQUIRE
Page 47 and 48: ©LeCroy Corporation4) When the pro
Page 49 and 50: ©LeCroy CorporationObservable Resu
Page 51 and 52: ©LeCroy CorporationTest OOB-04 - C
Page 57 and 58: ©LeCroy CorporationNOTE: The SATA
Page 59 and 60: ©LeCroy CorporationFigure B-2 Qual
Page 61 and 62: ©LeCroy CorporationAppendix C - Pr
Page 63 and 64: ©LeCroy CorporationAppendix D - Ve
Page 65 and 66: ©LeCroy Corporation3. On the oscil
Page 67 and 68: ©LeCroy Corporation15. Click on th
Page 69 and 70: ©LeCroy CorporationAppendix F - OO

1.0 - SATA-IO

Create successful ePaper yourself

Delete template?

Save as template?