youngAmericababy™ - Stanley Furniture

ASSEMBLING AND OPERATING YOUR CRIBNOTE: Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE REFERENCE.There is a clear plastic bag attached to the flat spring that can be used to store instructions.This crib conforms to JPMA-Juvenile Products Manufacturers Association and the CPSC-Consumer Product Safety Commission. Please adhere to the followingguidelines for assembly, operation and maintenance.PLIERSSCREWDRIVER(FLAT HEAD)SCREWDRIVER(PHILLIPS HEAD)TOOLS REQUIRED• Power tools are not recommended for assembling your furniture.• Give yourself plenty of room to work.• Due to the size of this bed, it must be assembled within the space it will occupy.• The assembly will require at least two people to complete.• Make sure all fasteners are tight.• Above all, take your time and read the instructions carefully.STEP 1.Attach wood stabilizer rails to the left and right crib ends.1. Insert barrel nuts into the holes on the inside of each end of the stabilizer rails as shown in SECTION “A”. Using a flatheadscrewdriver, align the slots in the barrel nuts with the center holes in the ends of the stabilizer rails. This will assure properalignment with the bolts that will be inserted.2. Align the dowels in the ends of one of the stabilizer railswith the upper and lower holes that are bored inthe panel near the bottom of the left crib end asshown in SECTION “A”. Make sure thenotched edge of the stabilizer rail is turned up.3. Insert a 2 3 /4" x 1 /4"-20 bolt through thehole that is bored through the panel betweenthe dowels. Using the allen wrench that isprovided, tighten the bolt so that the dowelsonly go into the panel about half way.Do not tighten securely at this point,as this will interfere with assembly steps that follow.4. Repeat steps 2 and 3 to attach the stabilizer rail to the right crib end.5. Repeat steps 2-4 using the second stabilizerrail on the opposite side of the crib.youngAmericababyA trademark of Stanley Furniture Company, Inc.5

STEP 2.Attach stationary side to left and right crib ends.1. Position the stationary side so that the top rail with the plastic teething protector is on top.2. One of the posts of the left crib end has 3 threaded inserts in it. Bolt the stationary side to the left crib end by inserting3 of the 1 3 /8" (1/4" - 20 thread) decorative bolts through the 3 holes located in the end spindle of the stationary side.Line the holes in the end of the stationary side up with the threaded inserts on the inside of the post of theheadboard and hand-tighten the 3 bolts. Do not tighten with allen wrench at this time.3. Repeat to attach the stationary side to the right crib end.youngAmericababyA trademark of Stanley Furniture Company, Inc.6

CAUTION: Any mattress in this crib must be at least 27- 1 /4 " by 51- 5 /8 " with athickness of no less than 5 inches and not exceeding 6 inches.MATTRESS5"MINIMUM THICKNESS6"MAXIMUM THICKNESSCRIB SPRING FRAMEOperating Drop-Side1. Lift drop-side rail up.2. Using the side of your leg, apply pressure to the bottom railof the drop-side gently toward the inside of the crib until you feel the locking mechanism release.3. Lower drop-side.4. To raise the drop-side, pull up on the drop-side rail. You will hear a click when it automatically locks into position.Maintaining Drop-Side1. Periodically check to make certain all screws are fastened securely..2. Check frequently that the crib spring brackets attached to the spring frame are securely attached to stabilizer rails.3. If you are missing a part or need a replacement part, do not use substitute parts. Ask your dealer for replacement parts or contactCustomer Service at (276) 627-21004. The spring adjustment bracket allows for the mattress to be lowered as your child grows. When your child reaches a height of 35 inches,or can climb out of the crib, you should place the child in a youth or regular bed.5. Save this instruction sheet in the event you disassemble the crib and need to reassemble it. This instruction sheet will also be usefulin identifying replacement parts if needed at a future date.youngAmericababyA trademark of Stanley Furniture Company, Inc.14

CLEANING:Mix together a mild solution of gentle dishwashing liquid and water, apply to crib surface using asoft clean cloth lightly dampened in the solution. Rinse with clear water again using a soft cleancloth, then dry all surfaces thoroughly with a soft dry cloth. NO ABRASIVE CLEANERS, SCOURINGPADS, STEEL WOOL, OR COARSE RAGS SHOULD BE USED TO CLEAN THIS FINE FURNITURE.STORAGE:A plastic pouch is attached to the crib spring for the storage of the assembly directions for futurereferral. After completing the assembly process, you are advised to read and be aware of allWARNINGS, CAUTIONS, CLEANING, STORAGE, USE AND MAINTENANCE notices contained in theseinstructions. We caution you not to place excess hardware in the plastic pouch as it could presentdanger to a child if retrieved and it could also puncture the crib mattress. When storing crib, useCAUTION as extreme temperature or humidity changes could be harmful.P.O. Box 30Stanleytown, VA 24168For parts, contact your Stanley dealer. For additionalconsumer information, call our Customer Services Department at1-(276) 627-2100. Mon. - Fri., 8-5 Eastern.youngAmericababyA trademark of Stanley Furniture Company, Inc.15