HCT-SDH-155 Manual

More documents

Recommendations

Info

6. Test ResultThe test result includes alarm test result, error code test result, pointer test result, overheadtest result, TCM test result, transparency test result, frequency test result and tributary test result,with the interface as in Figure 6-1. All test result menus have a save function. Click on the“Save“ shortcut key to save up the current test results.6.1. Alarm Test ResultFigure 6-1 test resultFor alarm test result interface, see Figure 6-2 as follows:Figure 6-2 Alarm Test Result“Alarm type”:34
PDH part: including continual seconds of LOS, AIS, LTI, LOF, RAI, CRCL, MAIS, CASL, MRAI,Pat AIS and Pat LSS. (Only in E1 mode)<strong>SDH</strong> part: including LOS, LOF, RS TIM, MS AIS, MS RDI, AU AIS, AU LOP, HP UNEQ, HP RDI,HP TIM, HP PLM, LTI, Pat AIS, Pat LSS, TU AIS (grey when set up as C4), TU LOP (grey when setup as C4), LP UNEQ (grey when set up as C4), LP RDI (grey when set up as C4), RFI (grey whenset up as C3 or C4), LP TIM (grey when set up as C4) and LP PLM (grey when set up as C4).In any interface, click on the “Start” shortcut key to start synchronous counting and operation.Click on ”Stop” button to stop. Click on the “Chart” shortcut key to generate a dynamic histogram ofalarm test results in this interface directly.6.2. Error Code Test ResultFor error code test result interface, see Figure 6-3 as follows:Figure 6-3 Error Code Test Result“Error type”:PDH part: including error code counting, sec & rate of ECOD, EFAS, ECRC, REBE and EBIT.(Only in E1 mode)<strong>SDH</strong> part: including error code counting, sec & rate of B1, B2, MRAI, HP B3, LP B3 (grey whenset up as C12 or C4), HP REI, LP REI (grey when set up as C4), EBIT and BIP2 (grey when set upas C3 or C4).In any interface, click on the “Start” shortcut key to start synchronous counting and operation.Click on the exit button to stop. Click on the “Chart” shortcut key to generate a dynamic histogram oferror test results in this interface directly.6.3. Pointer Test ResultFor pointer test result interface, see Figure 6-4 as follows:35
Page 1 and 2: HCT-SDH/155STM1/E1 Tester
Page 3 and 4: 7. System Setup....................
Page 5 and 6: ⑴ ⑵ ⑶ ⑷ ⑸ ⑹(1) Electric
Page 7 and 8: 1.2. Introduction to Graphical User
Page 9: Figure 2-3 Configuration FileClick
Page 12 and 13: Figure 2-11 PDH Monitor Mode2.1.8.
Page 14 and 15: Figure 2-16 Mapping Mode Setup2.2.4
Page 16 and 17: LTC: loss of external clockRS: rela
Page 18 and 19: LTC: TCM frame loss alarmRDI: TCM r
Page 20 and 21: 3.3. Error Performance Analyser3.3.
Page 22 and 23: Figure 3-8 G.821 Analyzer Interface
Page 24 and 25: 4. Event RecordEvent record interfa
Page 26 and 27: “Receive value of pointer“: rec
Page 28 and 29: 4.6. Insert AlarmFor insert alarm,
Page 30 and 31: 5. Function TestFunction test inclu
Page 32 and 33: “Err Mode”:Rate (default parame
Page 36 and 37: Figure 6-4 Pointer Test ResultPoint
Page 38 and 39: The display of the number, error co
Page 41 and 42: Figure 7-3 Configuration File7.1.2.
Page 43 and 44: corner to calibrate the screen as i

HCT-SDH-155 Manual

Create successful ePaper yourself

Delete template?

Save as template?