Wadkin PP Panel Dimension Saw Manual and Parts List

More documents

Recommendations

Info

WaaKin OPERATING AND MAINTENANCE INSTRUCTIONSSLIDING TABLE ASSEMBLYLock handles marked "E" fig. 6. With rails carrying linear bearings in position, and hexegon head screws holdingadjustable rail finger tight, lower table on to intermediate slide and insert four pi.eces of i" diameter steel; twoeach end, and adjust hexegon hole grubscrew at each end of table to trap i" diameter rods in position as shownin fig. 1.Insert wooden wedges at one end of table only and remove i" diameter rods at this end as shown in fig. 2.Enter two-thirds of the steel bridge between table and intermediate slide as shown in fig. 3.Nylon cages and i" diameter steel balls can now be inserted by holding each ball in nylon cage with one fingerof each hand and feeding into slide-way as shown in fig. 4.With bridge piece complete with nylon cages in position, remove wooden wedges and i" diameter rods and placein position end retaining plates at each end of slide-way.Traverse table to its full extent in one direction, fig. 5, and using an allen key adjust slide with screws marked"A" fig.6 until table moves freely in this position. Now traverse table to its full extent in the opposite directionand repeat adjustment with screwS marked "C". Centralise table and adjust slide with screws marked "Bit. Withtable traversed to its full extent check for slackness in the slide in both directions and if necessary re-adjust toeliminate. Check sliding table for alignment with main table by traversing table to its full extent and checkingwith straight edge across main and sliding tables; repeat this operation at the opposite end. ShoUld sliding tableneed re-aligning with main table, first remove dowel pins in brackets marked "D", slacken hexegon head screwsand adjust table in required direction as shown in fig. 6.www.wadkin.cominfo@wadkin.comPage 11
Wadkin OPERATINGANDMAINTENANCEINSTRUCTIONS18 il RIPPING SAW FOR GENERALWORK. PART No QS10.16" FLAT CROSS CUT QS816" HOLLOW GROUND QS91 8" HOLLOW GROUND QS1218" FLAT CROSS CUT SAW QS1114" HOLLOW GROUND SAW QS33for cutting Bakelite, Tufnol andsimilar materials.18" NOVELTY TYPE SAW QS84for cutting Plywood.www.wadkin.comSPINDLE AND PIN HOLES IN SAWS.SA WS FOR USE ONTHE P. P. TYPE DIMENSION SAWThe saws illustrated are specially manufactured andtensioned to run at high speed: it is thereforerecommended they are obtained from us. The teethare designed to give the best possible finish to thework.Always keep the teeth sharp with an even set onboth sides. Before putting a new saw to use it mustbe ranged down when running at normal speed andeach tooth brought to a sharp cutting edge.TUNGSTEN CARBIDE TIPPED SAWS14" TUNGSTEN CARBIDE TIPPED QS174for cutting Plywood, Hardwood &Asbestos.14" NOVELTY TUNGSTEN CARBIDETIPPED QS176for cutting Plastics and Plywood.16" TUNGSTEN CARBIDE TIPPED QS175for cutting Hardwoods and Plywood.info@wadkin.comPage 12
Page 1 and 2: "WADKIN" DIMENSION SAWTYPE IIpp lII
Page 3: Wadkin OPERATINGANDMAINTENANCEINSTR
Page 6: WciOKin OPERATING AND MAINTENANCEIN
Page 11: Wadkin OPERATINGANDMAINTENANCEINSTR
Page 15 and 16: Waakin OPERATING AND MAINTENANCE IN
Page 17: Wadkin OPERATING AND MAINTENANCEINS
Page 20 and 21: www.wadkin.cominfo@wadkin.com
Page 22 and 23: pp SPARE PARTS LISTPPI001/PP8PPI001
Page 24 and 25: PPlOOl/PP515PPIOOl/PP522PPI001/PP52
Page 26 and 27: PP1001/PK16PP100l/PT22PP100l/SG255P
Page 28 and 29: PP1 001/P1'1 7 5PP1001/ PP52pp10()1
Page 30 and 31: PP10Ol/PP522)P1 OOl/PP 523P100l/PP2
Page 32 and 33: ·----------------=. - .. ---------
Page 34: PP1001/PP531PP10Ol/PP256www.wadkin.

Wadkin PP Panel Dimension Saw Manual and Parts List

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?