DMC-FZ150PC DMC-FZ150PU DMC-FZ150EB DMC ... - Panasonic

More documents

Recommendations

Info

1.4. How to Discharge the E.Capacitor on Flash P.C.B.CAUTION:1. Be sure to discharge the E.capacitor on FLASH P.C.B..2. Be careful of the high voltage circuit on FLASH P.C.B. when servicing.[Discharging Procedure]1. Refer to the disassemble procedure and remove the necessary parts/unit.2. Install the insulation tube onto the lead part of resistor (ERG5SJ102:1kΩ /5W).(An equivalent type of resistor may be used.)3. Place a resistor between both terminals of E.capacitor on the FLASH P.C.B. for approx. 5 seconds.4. After discharging, confirm that the E.capacitor voltage is lower than 10V by using a voltmeter.Fig. F14
2 Warning2.1. Prevention of Electrostatic Discharge (ESD) to ElectrostaticallySensitive (ES) DevicesSome semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called ElectrostaticallySensitive (ES) Devices.The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge(ESD).1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on yourbody by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,which should be removed for potential shock reasons prior to applying power to the unit under test.2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminumfoil, to prevent electrostatic charge buildup or exposure of the assembly.3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" cangenerate electrical charge sufficient to damage ES devices.5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Mostreplacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparableconductive material).7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective materialto the chassis or circuit assembly into which the device will be installed.CAUTION :Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as thebrushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficientto damage an ES device).2.2. How to Recycle the Lithium Ion Battery (U.S. Only)5
Page 6 and 7: 2.3. Caution for AC Cord(For EB/GC)
Page 8 and 9: 3 Service Navigation3.1. Introducti
Page 10 and 11: 3.4. How to Define the Model Suffix
Page 12 and 13: [CASE 1. After replacing MAIN P.C.B
Page 14 and 15: 4 Specifications14
Page 16 and 17: 6 Measurements and AdjustmentsThe a
Page 18 and 19: S2. Voltage ChartNote) Indicated vo
Page 20 and 21: S3.2. Video/Audio Process Block Dia
Page 23 and 24: S-7
Page 25 and 26: S-9S-9S-9S-9LCD_ROTATE1KEY_IN2MOVIE
Page 27 and 28: EVF_RESETDPW_SD3R0V_CA1G9001$[18]G9
Page 29 and 30: S-13
Page 31 and 32: S-15S-15AC4AC23AD24AB10AD3AB9AB5F2E
Page 33 and 34: R608110023262524232423G23F23G22IC60
Page 35 and 36: S-19
Page 37 and 38: 2/4DMC-FZ150Power Section(Main P.C.
Page 39 and 40: S-23ConfidentialUntilSD_POWER_ON1R8
Page 41 and 42: S4.7. Gyro (GY) Schematic DiagramGF
Page 43 and 44: S4.9. Rear Operation (R) Schematic
Page 45 and 46: S-294321R5218R5010R9112R2021C5208R2
Page 47 and 48: S-31CL9015R605845443530252015105214
Page 49 and 50: Main P.C.B. (2/2)G6020 C-14 FG7001
Page 51 and 52: S6. Replacement Parts ListNote:1. *
Page 53 and 54:
DMC-FZ150EGK vol.2Ref.No. Part No.
show all

DMC-FZ150PC DMC-FZ150PU DMC-FZ150EB DMC ... - Panasonic

Create successful ePaper yourself

Delete template?

Save as template?